ASTM E1936-03(2007)
(Specification)Standard Reference Radiograph for Evaluating the Performance of Radiographic Digitization Systems
Standard Reference Radiograph for Evaluating the Performance of Radiographic Digitization Systems
SCOPE
1.1 This reference radiograph covers a series of test targets suitable for evaluating, quantifying, and documenting performance parameters of the radiographic digitization process or the electronic image reconstruction process, or both. This reference radiograph can be used for visual and electronic analysis of digitization systems. This is the first of three related standards. Subsequent standards will provide guidance on the use of the test targets and recommended system performance levels
1.2 This reference radiograph provides a series of test targets to provide a vehicle for the evaluation of spatial resolution, density contrast sensitivity, dynamic range, and spatial linearity as well as other aspects of a digitization system. The test targets are suitable for evaluating a digitization system with a spatial resolution down to ∼1/1000 in. [25 micrometres (μ)] a density contrast sensitivity down to 0.02 optical density (OD), a density range of 0.5 to 4.5 OD, and a film size capacity of 14 in. [355 mm] wide by 17 in. [431 mm] long.
1.3 The values stated in inch-pound units are to be regarded as the standard, with the exception of the spatial resolution targets (6.2 and 6.7) which are stated in SI units.
1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E1936–03 (Reapproved 2007)
Standard Reference Radiograph for
Evaluating the Performance of Radiographic Digitization
Systems
This standard is issued under the fixed designation E1936; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E1254 Guide for Storage of Radiographs and Unexposed
Industrial Radiographic Films
1.1 This reference radiograph covers a series of test targets
E1316 Terminology for Nondestructive Examinations
suitable for evaluating, quantifying, and documenting perfor-
E1411 Practice for Qualification of Radioscopic Systems
mance parameters of the radiographic digitization process or
2.2 ASME Standard:
the electronic image reconstruction process, or both. This
SectionV,Article2, MandatoryAppendixVI,DigitalImage
reference radiograph can be used for visual and electronic
Acquisition, Display, Interpretation and Storage for
analysis of digitization systems.This is the first of three related
Nuclear Applications
standards. Subsequent standards will provide guidance on the
2.3 ASTM Adjuncts:
use of the test targets and recommended system performance
Standard Reference Radiograph for Evaluating the Perfor-
levels
mance of Radiographic Digitization Systems
1.2 This reference radiograph provides a series of test
targets to provide a vehicle for the evaluation of spatial
3. Terminology
resolution, density contrast sensitivity, dynamic range, and
3.1 Definitions:
spatial linearity as well as other aspects of a digitization
3.1.1 Refer to Terminology E1316 for definitions of terms
system. The test targets are suitable for evaluating a digitiza-
used in this guide.
tion system with a spatial resolution down to ;1/1000 in. [25
3.2 Definitions of Terms Specific to This Standard:
micrometres (µ)] a density contrast sensitivity down to 0.02
3.2.1 converging line pairs—the targets located on the
optical density (OD), a density range of 0.5 to 4.5 OD, and a
reference radiograph that are used to determine the spatial
film size capacity of 14 in. [355 mm] wide by 17 in. [431 mm]
resolution of the digitization system.
long.
3.2.2 parallel line pairs—the targets located on the refer-
1.3 The values stated in inch-pound units are to be regarded
ence radiograph that are used in conjunction with the converg-
as the standard, with the exception of the spatial resolution
ing line pairs to determine the spatial resolution of the
targets (6.2 and 6.7) which are stated in SI units.
digitization system.
1.4 This standard does not purport to address the safety
3.2.3 reference radiograph—the single piece of industrial
concerns, if any, associated with its use. It is the responsibility
radiographic film containing all of the reference targets de-
of the user of this standard to establish appropriate safety and
scribed in this document.
health practices and determine the applicability of regulatory
3.2.4 scan line—it is a path that is one pixel high (vertical)
limitations prior to use.
by the number of pixels wide (horizontal), that is captured by
2. Referenced Documents the digitization system.The scan lines are added, one on top of
the other, to electronically reproduce the physical (analog) data
2.1 ASTM Standards:
in the horizontal (film width) and vertical (film length) direc-
E1079 Practice for Calibration of Transmission Densitom-
tions on the display monitor.
eters
3.2.5 spatial linearity—the accuracy to which a digitization
systemreproducesthephysicaldimension.Itisassessedwithin
a single scan line and from one scan line to the next (horizontal
ThisreferenceradiographisunderthejurisdictionofASTMCommitteeE07on
and vertical directions).
Nondestructive Testing and is the direct responsibility of Subcommittee E07.02 on
Reference Radiological Images.
Current edition approved Dec. 1, 2007. Published January 2008. Originally
approved in 1997. Last previous edition approved in 2003 as E1936 - 03. DOI:
10.1520/E1936-03R07. Available from American Society of Mechanical Engineers (ASME), ASME
For referenced ASTM standards, visit the ASTM website, www.astm.org, or International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.asme.org.
Standards volume information, refer to the standard’s Document Summary page on AvailablefromEPRINDECenter,NDEDivision,1300HarrisBlvd.,Charlotte,
the ASTM website. NC 28262.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
E1936–03 (2007)
3.2.6 spatial resolution—it is measured as the minimum with sizes of 8 in. [203 mm] by 10 in. [254 mm], 11 in. [279
distance detectable between two physically spaced lines (see mm] by 14 in. [355 mm], and 14 in. [355 mm] by 17 in. [430
6.2 spatial resolution targets). It is determined by the sampling
mm]. These have been created for digitization systems unable
rate in physical two-dimensional space and the system un- to accommodate film sizes up to 14 in. by 17 in. The reference
sharpness.
radiograph may be cut to custom fit a particular digitization
3.2.7 targets—the physical patterns on the reference radio-
system and still contain all of the necessary targets within each
graph that are used to evaluate the radiographic film digitiza-
of these areas that are represented on the illustration in Fig. 1.
tion system.
6.2 Spatial Resolution Targets—Theseconsistofthreeiden-
tical groups of at least 6 converging line pairs.The targets have
4. Significance and Use
a maximum resolution of no less than 20 line pairs per
4.1 This reference radiograph may be used to quantify the
millimetre (lp/mm) and a minimum resolution of no greater
performance characteristics of a radiographic digitization sys-
than 1 lp/mm. The three line pair groups are oriented in the 0°,
tem or to provide periodic evaluations of a digitization system
45°, and 90° positions. The maximum resolution is oriented
in a production mode to verify that appropriate operating
toward the corners of the reference radiograph, Reference
characteristics are being maint
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E1936–97 Designation: E 1936 – 03 (Reapproved 2007)
Standard Reference Radiograph for
Evaluating the Performance of Radiographic Digitization
Systems
This standard is issued under the fixed designation E 1936; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This reference radiograph covers a series of test targets suitable for evaluating, quantifying, and documenting performance
parameters of the radiographic digitization process or the electronic image reconstruction process, or both. This reference
radiograph can be used for visual and electronic analysis of digitization systems. This is the first of three related standards.
Subsequent standards will provide guidance on the use of the test targets and recommended system performance levels
1.2 Thisreferenceradiographprovidesaseriesoftesttargetstoprovideavehiclefortheevaluationofspatialresolution,density
contrast sensitivity, dynamic range, and spatial linearity as well as other aspects of a digitization system. The test targets are
suitable for evaluating a digitization system with a spatial resolution down to ;1/1000 in. [25 micrometeres (µ)] a density contrast
sensitivity down to 0.02 optical density (OD), a density range of 0.5 to 4.5 OD, and a film size capacity of 14 in. (355 mm)[355
mm] wide by 17 in. (431 mm)[431 mm] long.
1.3 The values stated in inch-pound units are to be regarded as the standard, with the exception of the spatial resolution targets
(6.2 and 6.66.7) which are stated in SI units.
1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations
prior to use.
2. Referenced Documents
2.1 ASTM Standards:
E 1079 Practice for Calibration of Transmission Densitometers
E 1254 Guide for Storage of Radiographs and Unexposed Industrial Radiographic Films
E 1316 Terminology for Nondestructive Examinations
E 1411 Practice for Qualification of Radioscopic Systems
2.2 ASME Standard:
Section V, Article 2, Mandatory Appendix VI, Digital Image Acquisition, Display, Interpretation and Storage for Nuclear
Applications
2.3 ASTM Adjuncts:
Standard Reference Radiograph for Evaluating the Performance of Radiographic Digitization Systems
3. Terminology
3.1 Definitions:
3.1.1 Refer to Terminology E 1316 for definitions of terms used in this guide.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 converging line pairs—the targets located on the reference radiograph that are used to determine the spatial resolution of
the digitization system.
This reference radiograph is under the jurisdiction of ASTM Committee E-07 on Nondestructive Testing and is the direct responsibility of Subcommittee E07.02 on
Reference Radiological Images.
Current edition approved Dec. 10, 1997. Published June 1998.
This reference radiograph is under the jurisdiction of ASTM Committee E07 on Nondestructive Testing and is the direct responsibility of Subcommittee E07.02 on
Reference Radiological Images.
Current edition approved Dec. 1, 2007. Published January 2008. Originally approved in 1997. Last previous edition approved in 2003 as E1936 - 03.
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 03.03.volume information, refer to the standard’s Document Summary page on the ASTM website.
Available from American Society of Mechanical Engineers, 345 E. 47th Street, New York, NY 10017.
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
Available from EPRI NDE Center, NDE Division, 1300 Harris Blvd., Charlotte, NC 28262.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
E 1936 – 03 (2007)
3.2.2 dynamic range—the range of optical densities over which a predetermined density contrast sensitivity can be maintained
in a single image.
3.2.3image—the digital representation of the target on the reference radiograph. The image of the target is used to evaluate both
the digitization and display aspects of the radiographic film digitization system.
3.2.4parallel line pairs—the targets located on the reference radiograph that are used in conjunction with the converging line
pairs to determine the spatial resolution of the digitization system.
3.2.5
3.2.3 reference radiograph—the single piece of industrial radiographic film containing all of the reference targets described in
this document.
3.2.6
3.2.4 scan line—it is a path that is one pixel high (vertical) by the number of pixels wide (horizontal), that is captured by the
digitization system. The scan lines are added, one on top of the other, to electronically reproduce the physical (analog) data in the
horizontal (film width) and vertical (film length) directions on the display monitor.
3.2.7
3.2.5 spatial linearity—the accuracy to which a digitization system reproduces the physical dimension. It is assessed within a
single scan line and from one scan line to the next (horizontal and vertical directions).
3.2.8
3.2.6 spatial resolution—the size of the smallest piece of information on the radiograph which can be captured, digitized, and
displayed by the radiographic film digitization system.
3.2.9—it is measured as the minimum distance detectable between two physically spaced lines (see 6.2 spatial resolution
targets). It is determined by the sampling rate in physical two-dimensional space and the system unsharpness.
3.2.7 targets—the physical patterns on the reference radiograph that are used to evaluate the radiographic film digitization
system.
4. Significance and Use
4.1 This reference radiograph may be used to quantify the performance characteristics of a radiographic digitization system or
to provide periodic evaluations of a digitization system in a production mode to verify that appropriate operating characteristics
are being maintained. This reference radiograph provides a means for verifying the performance of a digitization system in much
the same way that the tests described in Practice E 1411, provide for the verification of a radioscopic imaging system. It may be
used to evaluate the performance of a digitization system in accordance with the requirements contained in ASME Section V,
Article 2, Mandatory Appendix VI, or other documents invoking requirements of this reference radiograph.
4.2This reference does provide a tool that allows the user to determine the performance of their radiographic digitization system.
Use of the reference radiograph requires an agreement between the using parties on the digitization practices and acceptable levels
of performance. This reference radiograph ma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.