ASTM C913-16
(Specification)Standard Specification for Precast Concrete Water and Wastewater Structures
Standard Specification for Precast Concrete Water and Wastewater Structures
SCOPE
1.1 This specification covers the recommended design requirements and manufacturing practices for monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, septic tanks, grease interceptor tanks, and items included under the scope of Specification C478.
Note 1: Water and wastewater structures are defined as solar heating reservoirs, cisterns, holding tanks, leaching tanks, extended aeration tanks, wet wells, pumping stations, distribution boxes, oil-water separators, treatment plants, manure pits, catch basins, drop inlets, and similar structures.
Note 2: Installation and sealant requirements should receive special consideration due to special features of the application.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C913 −16
Standard Specification for
1
Precast Concrete Water and Wastewater Structures
This standard is issued under the fixed designation C913; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope C39/C39M Test Method for Compressive Strength of Cylin-
drical Concrete Specimens
1.1 This specification covers the recommended design re-
C94/C94M Specification for Ready-Mixed Concrete
quirements and manufacturing practices for monolithic or
C125 Terminology Relating to Concrete and Concrete Ag-
sectionalprecastconcretewaterandwastewaterstructureswith
gregates
the exception of concrete pipe, box culverts, utility structures,
C150 Specification for Portland Cement
septic tanks, grease interceptor tanks, and items included under
C173 Test Method for Air Content of Freshly Mixed Con-
the scope of Specification C478.
crete by the Volumetric Method
NOTE 1—Water and wastewater structures are defined as solar heating
C231 Test Method for Air Content of Freshly Mixed Con-
reservoirs,cisterns,holdingtanks,leachingtanks,extendedaerationtanks,
crete by the Pressure Method
wet wells, pumping stations, distribution boxes, oil-water separators,
treatment plants, manure pits, catch basins, drop inlets, and similar C260 Specification for Air-Entraining Admixtures for Con-
structures.
crete
NOTE 2—Installation and sealant requirements should receive special
C330 Specification for Lightweight Aggregates for Struc-
consideration due to special features of the application.
tural Concrete
1.2 The values stated in inch-pound units are to be regarded
C478 Specification for Circular Precast Reinforced Concrete
as the standard. The values given in parentheses are for
Manhole Sections
information only.
C494/C494M Specification for Chemical Admixtures for
Concrete
2. Referenced Documents
C595 Specification for Blended Hydraulic Cements
2
2.1 ASTM Standards:
C618 Specification for Coal Fly Ash and Raw or Calcined
A184/A184M Specification for Welded Deformed Steel Bar
Natural Pozzolan for Use in Concrete
Mats for Concrete Reinforcement
C685/C685M Specification for Concrete Made by Volumet-
A416/A416M Specification for Low-Relaxation, Seven-
ric Batching and Continuous Mixing
Wire Steel Strand for Prestressed Concrete
C890 Practice for Minimum Structural Design Loading for
A421/A421M Specification for Stress-Relieved Steel Wire
Monolithic or Sectional Precast Concrete Water and
for Prestressed Concrete
Wastewater Structures
A615/A615M SpecificationforDeformedandPlainCarbon-
C990 Specification for Joints for Concrete Pipe, Manholes,
Steel Bars for Concrete Reinforcement
and Precast Box Sections Using Preformed Flexible Joint
A706/A706M Specification for Deformed and Plain Low-
Sealants
Alloy Steel Bars for Concrete Reinforcement
C1157 Performance Specification for Hydraulic Cement
A1064 Specification for Carbon-Steel Wire and Welded
Wire Reinforcement, Plain and Deformed, for Concrete 2.2 American Concrete Institute Standard:
C33 Specification for Concrete Aggregates ACI 318 Building Code Requirements for Reinforced Con-
3
crete
2.3 Federal Specification:
1
This specification is under the jurisdiction ofASTM Committee C27 on Precast
SS-S-210A Sealing Compound, Preformed Plastic, for Ex-
ConcreteProductsandisthedirectresponsibilityofSubcommitteeC27.30onWater
4
pansion Joints and Pipe Joints
and Wastewater Containers.
Current edition approved July 1, 2016. Published July 2016. Originally approved
in 1979. Last previous edition approved in 2008 as C913 – 08. DOI: 10.1520/
C0913-16.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Hills, MI 48333-9094, http://www.aci-int.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from Standardization Documents, Order Desk, Bldg. 4, Section D,
the ASTM website. 700 Robbins Ave., Philadelphia, PA 19111-5094. Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C913−16
3. Ordering Information A421/A421M for prestressed wire and strand; or Specification
A184/A184M, A615/A615M,or A706/A706M for bars.
3.1 Unless otherwise designated by the purchaser before
placing an order, a structure designed in accordance with
5. Design Requirements
Section 5 of this specification and fou
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C913 − 08 C913 − 16
Standard Specification for
1
Precast Concrete Water and Wastewater Structures
This standard is issued under the fixed designation C913; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers the recommended design requirements and manufacturing practices for monolithic or sectional
precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, septic tanks,
grease interceptor tanks, and items included under the scope of Specification C478.
NOTE 1—Water and wastewater structures are defined as solar heating reservoirs, cisterns, holding tanks, leaching tanks, extended aeration tanks, wet
wells, pumping stations, distribution boxes, oil-water separators, treatment plants, manure pits, catch basins, drop inlets, and similar structures.
NOTE 2—InsulationInstallation and sealant requirements should receive special consideration due to special features of the application.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
2. Referenced Documents
2
2.1 ASTM Standards:
3
A82/A82M Specification for Steel Wire, Plain, for Concrete Reinforcement (Withdrawn 2013)
A184/A184M Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement
3
A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete (Withdrawn 2013)
A416/A416M Specification for Low-Relaxation, Seven-Wire Steel Strand for Prestressed Concrete
A421/A421M Specification for Stress-Relieved Steel Wire for Prestressed Concrete
3
A496/A496M Specification for Steel Wire, Deformed, for Concrete Reinforcement (Withdrawn 2013)
3
A497/A497M Specification for Steel Welded Wire Reinforcement, Deformed, for Concrete (Withdrawn 2013)
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A616/A616MA706/A706M Specification for Rail-Steel Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
(Withdrawn 1999)
A617/A617MA1064 Specification for Axle-Steel Deformed and Plain Bars for Concrete ReinforcementCarbon-Steel Wire and
Welded Wire Reinforcement, Plain and Deformed, for Concrete (Withdrawn 1999)
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
C33 Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C94/C94M Specification for Ready-Mixed Concrete
C125 Terminology Relating to Concrete and Concrete Aggregates
C150 Specification for Portland Cement
C173 Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C260 Specification for Air-Entraining Admixtures for Concrete
C330 Specification for Lightweight Aggregates for Structural Concrete
C478 Specification for Circular Precast Reinforced Concrete Manhole Sections
C494/C494M Specification for Chemical Admixtures for Concrete
C595 Specification for Blended Hydraulic Cements
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
and Wastewater Containers.
Current edition approved Jan. 15, 2008July 1, 2016. Published February 2008July 2016. Originally approved in 1979. Last previous edition approved in 20072008 as
C913 – 07a.C913 – 08. DOI: 10.1520/C0913-08. 10.1520/C0913-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C913 − 16
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C685/C685M Specification for Concrete Made by Volumetric Batching and Continuous Mixing
C890 Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.