ASTM D6167-97(2004)
(Guide)Standard Guide for Conducting Borehole Geophysical Logging: Mechanical Caliper
Standard Guide for Conducting Borehole Geophysical Logging: Mechanical Caliper
SIGNIFICANCE AND USE
An appropriately developed, documented, and executed guide is essential for the proper collection and application of caliper logs. This guide is to be used in conjunction with Guide D 5753.
The benefits of its use include the following: improving selection of caliper logging methods and equipment, caliper log quality and reliability, and usefulness of the caliper log data for subsequent display and interpretation.
This guide applies to commonly used caliper logging methods for geotechnical applications.
It is essential that personnel (see the Personnel section of Guide D 5753) consult up-to-date textbooks and reports on the caliper technique, application, and interpretation methods.
SCOPE
1.1 This guide covers the general procedures necessary to conduct caliper logging of boreholes, wells, access tubes, caissons, or shafts (hereinafter referred as boreholes) as commonly applied to geologic, engineering, ground-water and environmental (hereinafter eeferred as geotechnical) investigations. Caliper logging for mineral or petroleum exploration and development are excluded.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6167–97 (Reapproved 2004)
Standard Guide for
Conducting Borehole Geophysical Logging: Mechanical
Caliper
This standard is issued under the fixed designation D6167; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.9 This guide does not purport to address all of the safety
and liability problems (for example, lost or lodged probes and
1.1 This guide covers the general procedures necessary to
equipment decontamination) associated with its use.
conduct caliper logging of boreholes, wells, access tubes,
1.10 This standard does not purport to address all of the
caissons, or shafts (hereafter referred as boreholes) as com-
safety concerns, if any, associated with its use. It is the
monly applied to geologic, engineering, ground-water, and
responsibility of the user of this standard to establish appro-
environmental (hereafter referred as geotechnical) investiga-
priate safety and health practices and determine the applica-
tions.Caliperloggingformineralorpetroleumexplorationand
bility of regulatory limitations prior to use.
development are excluded.
1.2 This guide defines a caliper log as a record of borehole
2. Referenced Documents
diameter with depth.
2.1 ASTM Standards:
1.2.1 Caliper logs are essential in the interpretation of
D653 Terminology Relating to Soil, Rock, and Contained
geophysical logs since they can be significantly affected by
Fluids
borehole diameter.
D5088 Practice for Decontamination of Field Equipment
1.2.2 Caliper logs are commonly used to measure borehole
Used at Waste Sites
diameter, shape, roughness, and stability; calculate borehole
D5608 Practices for Decontamination of Field Equipment
volume; provide information on borehole construction; and
Used at Low Level Radioactive Waste Sites
delineate lithologic contacts, fractures, and solution cavities
D5753 Guide for Planning and Conducting Borehole Geo-
and other openings.
physical Logging
1.3 This guide is restricted to mechanically based devices
with spring-loaded arms, which are the most common calipers
3. Terminology
used in caliper logging with geotechnical applications.
3.1 Definitions: Definitions shall be in accordance with
1.4 This guide provides an overview of caliper logging,
Terminology D653, Section 12, Ref (1), or as defined below:
including general procedures, specific documentation, calibra-
3.1.1 accuracy, n—how close a measured log values ap-
tion and standardization, and log quality and interpretation.
proaches true value. It is determined in a controlled environ-
1.5 To obtain additional information on caliper logs see
ment. A controlled environment represents a homogeneous
Section 9 of this guide.
sample volume with known properties.
1.6 This guide is to be used in conjunction with Guide
3.1.2 depth of investigation, n—the radial distance from the
D5753.
measurement point to a point where the predominant measured
1.7 This guide should not be used as a sole criterion for
responsemaybeconsideredcentered,thatisnottobeconfused
caliper logging and does not replace professional judgement.
with borehole depth (for example, distance) measured from the
Caliper logging procedures should be adapted to meet the
surface.
needs of a range of applications and stated in general terms so
3.1.3 measurement resolution, n—the minimum change in
that flexibility or innovation is not suppressed.
measured value that can be detected.
1.8 The geotechnical industry uses English or SI units. The
3.1.4 repeatability, n—the difference in magnitude of two
caliper log is typically recorded in units of inches, millimetres,
measurements with the same equipment and in the same
or centimetres.
environment.
1 2
This guide is under the jurisdiction ofASTM Committee D18 on Soil and Rock For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and is the direct responsibility of Subcommittee D18.01 on Surface and Subsurface contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Characterization. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved July 1, 2004. Published August 2004. Originally the ASTM website.
´1 3
approved in 1997. Last previous edition approved in 1997 as D6167 - 97 . DOI: The boldface numbers given in parentheses refer to a list of references at the
10.1520/D6167-97R04. end of the text.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D6167–97 (2004)
3.1.5 vertical resolution, n—the minimum thickness that
can be separated into distinct units.
3.1.6 volume of investigation, n—the volume that contrib-
utes 90 % of the measured response. It is determined by a
combination of theoretical and empirical modeling. The vol-
ume of investigation is non-spherical and has gradational
boundaries.
4. Summary of Guide
4.1 This guide applies to borehole caliper logging and is to
be used in conjunction with Guide D5753.
4.2 This guide briefly describes the significance and use,
apparatus, calibration and standardization, procedures, and
reports for conducting borehole caliper logging.
FIG. 1 Probe for Making Side-Collimated Gamma-Gamma Logs
5. Significance and Use
with Single-Arm Caliper (2)
5.1 An appropriately developed, documented, and executed
guide is essential for the proper collection and application of
caliper logs.This guide is to be used in conjunction with Guide
D5753.
5.2 The benefits of its use include the following: improving
selection of caliper logging methods and equipment, caliper
logqualityandreliability,andusefulnessofthecaliperlogdata
for subsequent display and interpretation.
5.3 This guide applies to commonly used caliper logging
methods for geotechnical applications.
5.4 It is essential that personnel (see the Personnel section
of Guide D5753) consult up-to-date textbooks and reports on
the caliper technique, application, and interpretation methods.
6. Interferences
6.1 Most extraneous effects on caliper logs are caused by
instrument problems and borehole conditions.
6.2 Instrument problems include the following: electrical
leakage of cable and grounding problems, temperature drift,
wear of mechanical components including the hinge pins and
in the linear potentiometer (mechanical hysteresis), damaged
or bent arms, and lack of lubrication of the mechanical
FIG. 2 Three-Arm Averaging Caliper
components.
6.3 Borehole conditions include heavy drilling mud, bore-
hole deviation, and drilling-related borehole irregularities. move together, which provides an average diameter measure-
ment. This caliper provides higher resolution than the single-
7. Apparatus
arm caliper measurement (see Fig. 3).
7.1 Ageophysical logging system has been described in the 7.2.3 Multiple independent arm calipers generally have
general guide (see the Apparatus section of Guide D5753). three or four independent arms of equal length; these arms are
7.2 Caliper logs may be obtained with probes having a sometimes oriented. Horizontal resolution, that provides accu-
single arm, three arms (averaging or summation), multiple rate borehole-diameter measurement regardless of borehole
independent arms (x-y caliper), multiple-feeler arms, bow shape,isrelatedtothenumberofindependentarms.Ingeneral,
springs, or gap wheels. Single-arm and three-arm averaging calipers with four or more independent arms will have higher
probes are most commonly used for geotechnical investiga- resolution than three-arm averaging (see Fig. 3). The four
tions. independent-arm caliper log may show borehole elongation
7.2.1 A single-arm caliper commonly provides a record of (elliptical borehole shape) and better indicates the actual
borehole diameter while being used to decentralize another irregularity of the borehole.
type of log, such as a side-collimated gamma-gamma probe 7.3 Caliper probes using arms are typically spring loaded.
(see Fig. 1). The caliper arm generally follows the high side of The arms are retracted and opened with an electric motor and
a deviated hole. The single-arm decentralizing caliper may not retention spring. The arms and gears are lubricated. Caliper
have the resolution needed for some applications. probes closed by hand are held closed with an electric solenoid
7.2.2 The three-arm averaging or summation caliper has or weighted retention ring that is released with a sudden drop.
arms of equal length oriented 120° apart (see Fig. 2).All arms Typically, the caliper arms are mechanically connected to a
D6167–97 (2004)
8.1.2 Caliper logs can be used in a qualitative (for example,
comparative) or quantitative (for example, borehole diameter
corrections) manner depending upon the project objectives.
8.1.3 Caliper calibration methods and frequency shall be
sufficient to meet project objectives.
8.1.3.1 Calibrationandstandardizationshouldbeperformed
eachtimeacaliperprobeissuspectedtobedamaged,modified,
repaired, and at periodic intervals.
8.2 Calibration is the process of establishing values for
caliper response and is accomplished with a physical model of
a known diameter. Calibration data values related to the
physical properties (for example, borehole diameter, rough-
ness) may be recorded in units (for example, counts per
second), that can be converted to units of length (for example,
inches, millimetres, or centimetres.)
8.2.1 At least two, and preferably more, values, which
approximate the anticipated operating range, are needed to
establish a calibration curve (for example, 4- and 10-in. (10.2-
and 25.4-cm) rings) if the borehole diameter to be logged is 5
in. (12.7 cm)).
8.2.2 Physical models of measured diameter that may be
used to calibrate the caliper response may include rings or bars
FIG. 3 Caliper Logs From Probes Having Four Independent Arms,
made of rigid materials that are not easily deformed and resist
Three Averaging Arms, and a Single Arm, Madison Limestone
wear.
Test Well 1, Wyoming (2)
8.2.2.1 Calibrationofcaliperprobesisdonemostaccurately
in rings of different diameters.
8.2.2.2 Acalibration bar is a plate that is drilled and marked
linear or rotary potentiometer such that changes in the angle of
at regular intervals and machined to fit over the body of the
the arms causes changes in resistance. These changes in
probe(seeFig.4).Onearmisplacedintheappropriateholefor
resistance are proportional to average borehole diameter. In
the range to be logged.
some probes, the voltage changes are converted to a varying
8.2.2.3 Calibration can be checked by using casing of
pulserateordigitizeddownholetoeliminateorminimizecable
measured diameter logged in the borehole.
transmission noise. Different arm length can be used to
8.3 Standardization is the process of checking logging
optimize sensitivity for the borehole-diameter range expected.
response to show evidence of repeatability and consistency.
7.4 The concepts of volume of investigation and depth of
8.3.1 Calibration serves as a check of standardization.
investigation are not applicable to caliper logs since it is a
8.3.2 Arepresentative borehole may be used to periodically
surface-contact measurement.
check caliper response providing the borehole environment
7.5 Vertical resolution of caliper measurements is a function
does not change with time. Caliper response may not repeat
of the size of the contact surface (arm tip or pad), the response
exactly because the probe may rotate, causing the arms to
of the mechanical and electronic components, and digitizing
follow slightly different paths within the borehole.
interval used. The theoretical limit of vertical resolution is
equal to the width of the caliper pad or tip. Selection of arm
9. Procedure
lengths and angle, and tip diameter will affect sensitivity.
9.1 See the Procedure section of Guide D5753 for planning
Shorter arms generally will provide more detail of the rugosity
a logging program, data formats, personnel qualifications, field
(borehole roughness as defined by Ref. (2)) of the borehole
documentation, and header documentation.
wall than longer arms. However, size of caliper probe and
9.2 Caliper specific information (for example, arm length)
borehole diameter may also determine arm lengths used.
should be documented.
7.6 Measurement resolution of typical caliper probes is 0.05
9.3 Identify caliper logging objectives.
in. (0.13 cm) of borehole diameter.
9.4 Select appropriate equipment to meet objectives.
7.7 A variety of caliper logging equipment is available for
9.4.1 Caliper equipment decontamination is addressed ac-
geotechnical investigations. It is not practical to list all of the
cording to project specifications (see Practice D5088 for
sources of potentially acceptable equipment.
non-radioactive waste sites and Practice D5608 for low level
radioactive waste sites). Some materials commonly used for
8. Calibration and Standardization of Caliper Logs
caliper-arm lubrication may be environmentally sensitive.
8.1 General:
9.5 Select the order in the logging sequence in which the
8.1.1 National Institute of Standards and Technology caliper probe is to be run (see 8.2.2.1 of Guide D5753).
(NIST) calibration and standardization procedures do not exist 9.5.1 Caliper probes are run before any probe utilizing
for caliper logging. nuclear sources and more expensive centralized probes.
D6167–97 (2004)
9.10.1 Maximum vertical resolution requires the selection
of a digitizing interval at least as small as the arm tip contact
height.
9.10.2 Typically, this interval is no larger than 0.1 ft (0.03
m) for high-resolution applications.
9.11 The caliper probe is lowered to the bottom of the
borehole.
9.11.1 Any time the caliper probe is lowered in the bore-
hole, the arms should be closed to avoid damaging equipment
or borehole.
9.11.2 Selection of probe speed while lowering is based on
knowledge of borehole depth, stability, and other conditions.
9.12 Open caliper arm(s).
9.13 Select logging speed.
9.13.1 Aloggingspeedofapproximately15ft(5m)permin
is recommended for high-resolution applications. Faster log-
gingspeedsmayinducenoiseduetothecaliperprobebumping
the borehole wall. Slower logging speeds will not enhance
measurement resolution for most systems.
9.14 Collect caliper data while the probe is moving up the
borehole.
9.15 When the probe reaches the top of the borehole:
9.15.1 If surface casing is present, compare and document
caliper measurement.
9.15.2 Check depth reference and document after survey
depth error (A
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.