ASTM D4640-86(2009)
(Test Method)Standard Test Method for Determining Stroke Cure Time of Thermosetting Phenol-Formaldehyde Resins
Standard Test Method for Determining Stroke Cure Time of Thermosetting Phenol-Formaldehyde Resins
SIGNIFICANCE AND USE
This method is significant as a process control for polymerization time.
When the cure times are determined at several temperatures and plotted as time versus temperature, different resins can be compared for curing characteristics.
SCOPE
1.1 This test method covers the determination of the cure rate at any specified temperature for a thermosetting phenol-formaldehyde resin. The time at that temperature required to make a fluid mixture change into a hard immovable mass indicates speed of cure.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4640 − 86 (Reapproved 2009)
Standard Test Method for
Determining Stroke Cure Time of Thermosetting Phenol-
Formaldehyde Resins
This standard is issued under the fixed designation D4640; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 5. Apparatus
5.1 Electric Hot Cure Plate, with a smooth surface free of
1.1 This test method covers the determination of the cure
rate at any specified temperature for a thermosetting phenol- rough spots with adjustable control to hold the temperature
within 3.5°F (2°C) (Note 1).
formaldehyde resin. The time at that temperature required to
make a fluid mixture change into a hard immovable mass
5.2 Spatula,3by ⁄16 in. (75 by 10 mm), stainless.
indicates speed of cure.
5.3 Stopwatch.
1.2 The values stated in inch-pound units are to be regarded
5.4 Knife, brass, putty with straight edge.
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
6. Procedure
and are not considered standard.
6.1 Adjust the hot plate to the desired test temperature.
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the NOTE 1—Usual temperatures are 300°F (150°C), 320°F (160°C), and
330°F (165°C).
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
6.2 Place an approximately 0.5-g specimen on the hot plate
2 2
bility of regulatory limitations prior to use.
and spread over an approximately 2-in. (130-mm ) area with
a clean spatula as quickly as possible. Start the stopwatch
2. Terminology immediately upon adding the specimen to the hot plate, then
stroke steadily across the specimen in alternating smoothing
2.1 Definitions of Terms Specific to This Standard:
and patting motions.
2.1.1 stroke cure time, n—the time required for a resin being
held at a specified temperature on a hot plate and being stroked 6.3 As the resin approaches the cured stage, it becomes
with a spatula, to adhere to the hot plate and not to the spatula. more viscous and stringy. Stop the stopwatch when the resin on
the hot plate and the spatula no longer adhere to each other.
3. Summary of Test Method Record the elapsed time.
6.4 Remove cured resin from hot plate immediately with the
3.1 This test method employs the use of controlled heat and
straight edged putty knife.
a thin layer of resin to determine the time in seconds required
to change from a fluid stage to a cured immovable stage.
NOTE 2—The longer on the ho
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D4640–86(Reapproved2001) Designation: D4640 – 86 (Reapproved 2009)
Standard Test Method for
Determining Stroke Cure Time of Thermosetting Phenol-
Formaldehyde Resins
This standard is issued under the fixed designation D4640; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the determination of the cure rate at any specified temperature for a thermosetting phenol-
formaldehyde resin. The time at that temperature required to make a fluid mixture change into a hard immovable mass indicates
speed of cure.
1.2
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Terminology
2.1 Definitions of Terms Specific to This Standard:
2.1.1 stroke cure timestroke cure time, n—the time required for a resin being held at a specified temperature on a hot plate and
being stroked with a spatula, to adhere to the hot plate and not to the spatula.
3. Summary of Test Method
3.1 This test method employs the use of controlled heat and a thin layer of resin to determine the time in seconds required to
change from a fluid stage to a cured immovable stage.
4. Significance and Use
4.1 This method is significant as a process control for polymerization time.
4.2 When the cure times are determined at several temperatures and plotted as time versus temperature, different resins can be
compared for curing characteristics.
5. Apparatus
5.1 Electric Hot Cure Plate, with a smooth surface free of rough spots with adjustable control to hold the temperature within
3.5°F (2°C) (Note 1).
5.2 Spatula,3by ⁄16 in. (75 by 10 mm), stainless.
5.3 Stopwatch.
5.4 Knife, brass, putty with straight edge.
6. Procedure
6.1 Adjust the hot plate to the desired test temperature.
NOTE 1—Usual temperatures are 300°F (150°C), 320°F (160°C), and 330°F (165°C).
2 2
6.2 Place an approximately 0.5-g specimen on the hot plate and spread over an approximately 2-in. (130-mm ) area with a
cleanspatulaasquicklyaspossible.Startthestopwatchimmediatelyuponaddingthespecimentothehotplate,thenstrokesteadily
across the s
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.