ASTM E2462-18
(Specification)Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
Standard Performance Specification for Cargo Bed Cover (CBC) HMMWV, Type I
SCOPE
1.1 Scope—This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit, M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:E2462 −18
Standard Performance Specification for
1
Cargo Bed Cover (CBC) HMMWV, Type I
This standard is issued under the fixed designation E2462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Rigid Wall Relocatable Structures
3
1.1 Scope—This specification covers the performance re- 2.2 Army Standards:
quirementsfortheTypeICargoBedCover(CBC).TheTypeI
ARMYTM9-2320-280-10HMMWV’S Operator’s Manual
Cargo Bed Cover is a removable general purpose rigid enclo-
ARMYTM10-5411-231-13&PTechnical Manual
sure for the cargo bed of the M1152A1, M1152A1 with B2
2.3 Commercial Standards:
Armor Kit, M1037, M1042, M1097, and M1113 High-
ANSI/ASQCZ1.4-2003 Sampling Procedures and Tables
Mobility Multipurpose Wheeled Vehicle (HMMWV). The
4
for Inspection by Attributes
TypeICBCprovidesenvironmentalprotectionandsecurityfor
SAE AS8090 Mobility, Towed Aerospace Ground
mission equipment and items of general transport.
5
Equipment, General Requirements for
1.2 The values stated in SI units are to be regarded as
6
2.4 Federal Standard:
standard. The values given in parentheses are mathematical
FED-STD-595Colors Used in Government Procurement
conversions to inch-pound units that are provided for informa-
6
tion only and are not considered standard.
2.5 Military Standards:
MIL-STD-129Military Marking For Shipment and Storage
1.3 The following safety hazards caveat pertains only to the
MIL-STD-209Interface Standard for Lifting and Tie-down
test required portion, Section 5, of this specification. This
Provisions
standard does not purport to address all of the safety concerns,
MIL-STD-810Environmental Engineering Considerations
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety, health, and and Laboratory Tests
environmental practices and determine the applicability of MIL-STD-913Requirements for the Certification of Sling
regulatory limitations prior to use. Loaded Military Equipment for External Transportation
1.4 This international standard was developed in accor- by Department of Defense Helicopters
dance with internationally recognized principles on standard-
MIL-STD-1366Transportability Criteria
ization established in the Decision on Principles for the
MIL-PRF-22750Coating, Epoxy, High Solids
Development of International Standards, Guides and Recom-
MIL-C-46168Coating, Aliphatic Polyurethane, Chemical
mendations issued by the World Trade Organization Technical
Agent Resistant
Barriers to Trade (TBT) Committee.
MIL-C-53039 Coating, Aliphatic Polyurethane, Single
Component, Chemical Agent Resistant
2. Referenced Documents
MIL-DTL-53072 Chemical Agent Resistant Coating
2
2.1 ASTM Standards: (CARC)SystemApplicationProceduresandQualityCon-
E631Terminology of Building Constructions trol Inspection
E1749Terminology Relating to Rigid Wall Relocatable
6
2.6 Military Handbook:
Shelters
MIL-HDBK-1791Designing for InternalAerial Delivery in
E1925Specification for Engineering and Design Criteria for
Fixed Winged Aircraft
1
This specification is under the jurisdiction of ASTM Committee E06 on
3
Performance of Buildings and is the direct responsibility of Subcommittee E06.53 Shelter Technology, Engineering & Fabrication Directorate, U.S.Army Natick
on Materials and Processes for Durable Rigidwall Relocatable Structures. Soldier RD&E Center, ATTN: RDNS-ST, Kansas Street, Natick, MA 01760-5018,
Current edition approved Oct. 1, 2018. Published November 2018. Originally http://www.natick.army.mil.
4
approved in 2005. Last previous edition approved in 2010 as E2462–10. DOI: Available fromAmerican Society for Quality (ASQ), 600 N. PlankintonAve.,
10.1520/E2462–18 Milwaukee, WI 53203, http://www.asq.org.
2 5
For referenced ASTM standards, visit the ASTM website, www.astm.org, or AvailablefromSAEInternational(SAE),400CommonwealthDr.,Warrendale,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM PA 15096, http://www.sae.org.
6
Standards volume information, refer to the standard’s Document Summary page on Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
the ASTM website. Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E2462−18
2.7 The American Conference of Governmental Industrial
NSN Part
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E2462 − 10 E2462 − 18
Standard Performance Specification for
1
Cargo Bed Cover (CBC) HMMWV, Type I
This standard is issued under the fixed designation E2462; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 Scope—This specification covers the performance requirements for the Type I Cargo Bed Cover (CBC). The Type I Cargo
Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M1152A1, M1152A1 with B2 Armor Kit,
M1037, M1042, M1097, and M1113 High-Mobility Multipurpose Wheeled Vehicle (HMMWV). The Type I CBC provides
environmental protection and security for mission equipment and items of general transport.
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions
to inch-pound units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test required portion, Section 45, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E631 Terminology of Building Constructions
E1749 Terminology Relating to Rigid Wall Relocatable Shelters
E1925 Specification for Engineering and Design Criteria for Rigid Wall Relocatable Structures
3
2.2 Army Standards:
ARMY TM 9-2320-280-10 HMMWV’S Operator’s Manual
ARMY TM 10-5411-231-13&P Technical Manual
2.3 Commercial Standards:
4
ANSI/ASQC Z1.4-2003 Sampling Procedures and Tables for Inspection by Attributes
5
SAE AS8090 Mobility, Towed Aerospace Ground Equipment, General Requirements for
6
2.4 Federal Standard:
FED-STD-595 Colors Used in Government Procurement
6
2.5 Military Standards:
MIL-STD-129 Military Marking For Shipment and Storage
MIL-STD-209 Interface Standard for Lifting and Tie-down Provisions
MIL-STD-810 Environmental Engineering Considerations and Laboratory Tests
1
This specification is under the jurisdiction of ASTM Committee E06 on Performance of Buildings and is the direct responsibility of Subcommittee E06.53 on Materials
and Processes for Durable Rigidwall Relocatable Structures.
Current edition approved Nov. 1, 2010Oct. 1, 2018. Published December 2010November 2018. Originally approved in 2005. Last previous edition approved in 20052010
as E2462 – 05.E2462–10. DOI: 10.1520/E2462-1010.1520/E2462–18
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
3
Shelter Technology, Engineering & Fabrication Directorate, USU.S. Army Natick Soldier RD&E Center, ATTN: RDNS-ST, Kansas Street, Natick, MA 01760-5018,
http://www.natick.army.mil.
4
Available from American Society for Quality (ASQ), 600 N. Plankinton Ave., Milwaukee, WI 53203, http://www.asq.org.
5
Available from SAE International (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001,15096, http://www.sae.org.
6
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA
19111-5098, http://dodssp.daps.dla.mil.19111-5094, http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E2462 − 18
MIL-STD-913 Requirements for the Certification of Sling Loaded Military Equipment for External Transportation by
Department of Defense Helicopters
MIL-STD-1366 Transportability Criteria
MIL-PRF-22750 Coating, Epoxy, High Solids
MIL-C-46168 Coating, Aliphatic Polyurethane, Chemical Agent
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.