ASTM B649-06(2016)
(Specification)Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), and Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire, and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire
Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925,<brk/> UNS N08031, UNS N08354, and UNS N08926), and <brk/>Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire, and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire
ABSTRACT
This specification covers Ni-Fe-Cr-Mo-Cu-N low-carbon alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), Cr-Ni-Fe-N low-carbon alloy (UNS R20033) bar and wire, and Ni-Cr-Fe Mo-N alloy (UNS N08936) wire. The material shall be supplied in the solution-treated or in cold drawn condition as required. Heat treatment shall be waived for forging quality material. The alloys shall conform to the chemical composition requirements prescribed for carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, copper, nitrogen, and iron, as determined by chemical or product (check) analysis, and to the tensile requirements including tensile strength, yield strength, and elongation, as determined by tension test.
SCOPE
1.1 This specification covers nickel-iron-chromium-molybdenum-copper-nitrogen alloys (UNS N08925, UNS N08031, UNS N08354, and UNS N08926), and chromium-nickel-iron-nitrogen low-carbon alloy (UNS R20033) bar and wire, and nickel-chromium-iron-molybdenum-nitrogen alloy (UNS N08936) wire.
1.2 ASTM International has adopted definitions whereby some grades, such as UNS N08904,2 previously in this specification were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification are now covered by Specifications A479/A479M and A484/A484M.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B649 −06(Reapproved 2016)
Standard Specification for
Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925,
UNS N08031, UNS N08354, and UNS N08926), and
Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire,
1
and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire
This standard is issued under the fixed designation B649; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
3
1.1 This specification covers nickel-iron-chromium- 2.1 ASTM Standards:
molybdenum-copper-nitrogen alloys (UNS N08925, UNS A479/A479M Specification for Stainless Steel Bars and
N08031, UNS N08354, and UNS N08926), and chromium- Shapes for Use in Boilers and Other Pressure Vessels
nickel-iron-nitrogen low-carbon alloy (UNS R20033) bar and A484/A484M Specification for General Requirements for
wire, and nickel-chromium-iron-molybdenum-nitrogen alloy Stainless Steel Bars, Billets, and Forgings
(UNS N08936) wire. B880 Specification for General Requirements for Chemical
Check Analysis Limits for Nickel, Nickel Alloys and
1.2 ASTM International has adopted definitions whereby
2
Cobalt Alloys
some grades, such as UNS N08904, previously in this
E8 Test Methods for Tension Testing of Metallic Materials
specification were recognized as stainless steels, because those
E29 Practice for Using Significant Digits in Test Data to
grades have iron as the largest element by mass percent. Such
Determine Conformance with Specifications
grades are under the oversight of ASTM Committee A01 and
E55 Practice for Sampling Wrought Nonferrous Metals and
itssubcommittees.TheproductsofN08904previouslycovered
Alloys for Determination of Chemical Composition
in this specification are now covered by Specifications A479/
E527 Practice for Numbering Metals and Alloys in the
A479M and A484/A484M.
Unified Numbering System (UNS)
1.3 The values stated in inch-pound units are to be regarded
E1473 Test Methods for Chemical Analysis of Nickel, Co-
as standard. The values given in parentheses are mathematical
balt and High-Temperature Alloys
conversions to SI units that are provided for information only
3. Terminology
and are not considered standard.
3.1 Definitions of Terms Specific to This Standard:
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the 3.1.1 bars, n—hot-finished rounds, squares, octagons, and
1
hexagons: ⁄4 in. (6.35 mm) and over in diameter or size.
responsibility of the user of this standard to become familiar
1
with all hazards including those identified in the appropriate Hot-finished flats: ⁄4 in. to 10 in. (254 mm) inclusive in width,
1
⁄8 in. (3.18 mm) and over in thickness. Cold-finished rounds,
Safety Data Sheet (SDS) for this product/material as provided
1
squares, octagons, hexagons, and shapes: over ⁄2 in. (12.70
by the manufacturer, to establish appropriate safety and health
3
mm) in diameter or size. Cold-finished flats: ⁄8 in. (9.52 mm)
practices, and determine the applicability of regulatory limi-
1
and over in width (see 3.1.1.1) and ⁄8 in. and over in thickness
tations prior to use.
(see 3.1.1.2).
3
3.1.1.1 Discussion—Widths less than ⁄8 in. (9.52 mm) and
1
3
This specification is under the jurisdiction of ASTM Committee B02 on
thicknesses less than ⁄16 in. (4.76 mm) are described generally
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
as flat wire.
B02.07 on Refined Nickel and Cobalt and Their Alloys.
Current edition approved June 1, 2016. Published June 2016. Originally
3
approved in 1981. Last previous edition approved in 2011 as B649 – 06 (2011). For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/B0649-06R16. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
New designation established in accordance with Practice E527 and SAE J1086, Standards volume information, refer to the standard’s Document Summary page on
Practice for Numbering Metals and Alloys (UNS).
the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B649−06(2016)
1 3
3.1.1.2 Discussion—Thickness ⁄8 in. to under ⁄16 in. (3.18 senting each heat or lot. Such analysis may be made by any of
mm to under 4.76 mm) can be cold-rolled strip as well as bar. the commonly accepted methods that will positively identify
the material.
3.1.2 wire, n—cold-finished only: round, square, octagon,
1
6.2.1 If a product analysis is made, the material shall
hexagon, and shape wire, ⁄2 in. (12.70 mm) and unde
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B649 − 06 (Reapproved 2011) B649 − 06 (Reapproved 2016)
Standard Specification for
Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloys (UNS N08925,
UNS N08031, UNS N08354, and UNS N08926), and
Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire,
1
and Ni-Cr-Fe-Mo-N Alloy (UNS N08936) Wire
This standard is issued under the fixed designation B649; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*Scope
1.1 This specification covers nickel-iron-chromium-molybdenum-copper-nitrogen alloys (UNS N08925, UNS N08031, UNS
N08354, and UNS N08926), and chromium-nickel-iron-nitrogen low-carbon alloy (UNS R20033) bar and wire, and nickel-
chromium-iron-molybdenum-nitrogen alloy (UNS N08936) wire.
2
1.2 ASTM International has adopted definitions whereby some grades, such as UNS N08904, previously in this specification
were recognized as stainless steels, because those grades have iron as the largest element by mass percent. Such grades are under
the oversight of ASTM Committee A01 and its subcommittees. The products of N08904 previously covered in this specification
are now covered by Specifications A479/A479M and A484/A484M.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet (MSDS)(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices,
and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
A479/A479M Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
1
3.1.1 bars, n—hot-finished rounds, squares, octagons, and hexagons: ⁄4 in. (6.35 mm) and over in diameter or size. Hot-finished
1 1
flats: ⁄4 in. to 10 in. (254 mm) inclusive in width, ⁄8 in. (3.18 mm) and over in thickness. Cold-finished rounds, squares, octagons,
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved May 1, 2011June 1, 2016. Published May 2011June 2016. Originally approved in 1981. Last previous edition approved in 20062011 as
B649 - 06.B649 DOI: 10.1520/B0649-06R11.– 06 (2011). DOI: 10.1520/B0649-06R16.
* New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
2
New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
B649 − 06 (2016)
1 3
hexagons, and shapes: over ⁄2 in. (12.70 mm) in diameter or size. Cold-finished flats: ⁄8 in. (9.52 mm) and over in width (see
1
3.1.1.1) and ⁄8 in. and ove
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.