ASTM F1074-87(2012)

Standard Specification for Cleats, Welded Horn Type

ABSTRACT
This specification covers hollow welded horn type cleats and pads for marine use. The cleats shall be used where securing of boat handling lines are required onboard commercial and navy boats and crafts. The horn cleats shall be of galvanized steel, grade 1023W; the base plate shall be of the prescribed steel composition; and all chafing surfaces shall have the specified finish. The cleats� horns shall be of cast steel, round in shape, and free of burrs or sharp edges. The requirements for welding of horns to a base plate are illustrated. The dimensional requirements for cleat, rope circumference, and roper diameter are specified. Requirements for packaging and product marking are given as well.
SCOPE
1.1 This specification covers hollow cleats and pads for marine use.  
1.2 The cleats shall be used where securing of boat handling lines are required onboard commercial and navy boats and crafts.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

General Information

• Status: Historical
• Publication Date: 31-May-2012
• ICS: 47.020.50 - Deck equipment and installations
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Relations

• Replaces: ASTM F1074-87(2007) - Standard Specification for Cleats, Welded Horn Type
• Effective Date: 01-Jun-2012

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1074 −87 (Reapproved 2012) An American National Standard
Standard Specification for
1
Cleats, Welded Horn Type
This standard is issued under the fixed designation F1074; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Ordering Information
3.1 Orders for material under this specification shall include
1.1 This specification covers hollow cleats and pads for
the following:
marine use.
3.1.1 Title, number, and date of this specification,
1.2 The cleats shall be used where securing of boat handling
3.1.2 Quantity,
lines are required onboard commercial and navy boats and
3.1.3 Size of cleats, and
crafts.
3.1.4 Packaging, packing, or marking requirements.
1.3 The values stated in inch-pound units are to be regarded
4. Materials and Manufacture
as the standard. The values given in parentheses are for
information only.
4.1 Material:
4.1.1 The horn cleats shall be of galvanized steel, grade
1.4 This international standard was developed in accor-
1023W, in accordance with Practice A385.
dance with internationally recognized principles on standard-
4.1.2 The base plate shall be of steel, (carbon 0.35
ization established in the Decision on Principles for the
maximum), in accordance with Specification A36/A36M.
Development of International Standards, Guides and Recom-
4.1.3 All chafing surfaces shall have a 125µ finish.
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
4.2 Manufacture—The cleats’ horns shall be of cast steel,
round in shape, and free of burrs or sharp edges. The horns
2. Referenced Documents
shall be welded to a base plate as shown in Fig. 1 (see Table 1).
The weld is to be ground smooth to prevent chafing of ropes.
2
2.1 ASTM Standards:
The base plate shall be oval shaped with smooth rounded
A36/A36M Specification for Carbon Structural Steel
edges. The dimensions shall be in accordance with Table 1.
A370 Test Methods and Definitions for Mechanical Testing
of Steel Products
5. Packaging
A385 Practice for Providing High-Quality Zinc Coatings
5.1 The packing shall afford protection against deterioration
(Hot-Dip)
andphysicaldamageduringshipmentfromthemanufacturerto
the using activity for immediate use.
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
6. Product Marking
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
6.1 Containers shall be stenciled with the ASTM standard
Current edition approved June 1, 2012. Published October 2012. Originally
designation, in black paint with approximately 1 in. (25.4 mm)
approved in 1987. Last previous edition approved in 2007 as F1074 – 87 (2007).
DOI: 10.1520/F1074-87R12. high letters and numbers with the following information:
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
6.1.1 Address,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
6.1.2 purchase order number, and
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. 6.1.3 Manufacturer’s name.
Copyri
...