ASTM F1282-01a
(Specification)Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
Standard Specification for Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe
SCOPE
1.1 This specification covers a coextruded polyethylene composite pressure pipe with a welded aluminum tube reinforcement between the inner and outer layers. The inner and outer polyethylene layers are bonded to the aluminum tube by a melt adhesive. Included is a system of nomenclature for the polyethylene-aluminum-polyethylene (PE-AL-PE) pipes, the requirements and test methods for materials, the dimensions and strengths of the component tubes and finished pipe, adhesion tests, and the burst and sustained pressure performance. Also given are the requirements and methods of marking.
1.2 This specification relates only to metal and plastic composite pipes incorporating a welded metallic tube. The welded metallic tube of itself is capable of sustaining internal pressures. Pipes consisting of metallic layers not welded together are outside the scope of this specification.
1.3 Specifications for connectors for use with pipe meeting the requirements of this specification are given in Annex A1.
1.4 This specification excludes crosslinked polyethylene-aluminum-crosslinked polyethylene pipes (see Specification F 1281).
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: F 1282 – 01a
Standard Specification for
Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite
1
Pressure Pipe
This standard is issued under the fixed designation F 1282; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
1.1 This specification covers a coextruded polyethylene 2.1 ASTM Standards:
composite pressure pipe with a welded aluminum tube rein- D 618 Practice for Conditioning Plastics and Electrical
2
forcement between the inner and outer layers. The inner and Insulating Materials for Testing
outer polyethylene layers are bonded to the aluminum tube by D 1248 Specification for Polyethylene Plastics Molding and
2
a melt adhesive. Included is a system of nomenclature for the Extrusion Materials
polyethylene-aluminum-polyethylene (PE-AL-PE) pipes, the D 1598 Test Method for Time-to-Failure of Plastic Pipe
3
requirements and test methods for materials, the dimensions Under Constant Internal Pressure
and strengths of the component tubes and finished pipe, D 1599 Test Method for Short-Time Hydraulic Failure Pres-
3
adhesion tests, and the burst and sustained pressure perfor- sure of Plastic Pipe, Tubing, and Fittings
mance. Also given are the requirements and methods of D 1600 Terminology for Abbreviated Terms Relating to
2
marking. The pipe covered by this specification is intended for Plastics
2
use in potable water distribution systems for residential and D 1898 Practice for Sampling of Plastics
commercial applications, water service, underground irrigation D 2104 Specification for Polyethylene (PE) Plastic Pipe,
3
systems, and radiant panel heating systems, baseboard, snow- Schedule 40
and ice-melt systems, and gases that are compatible with D 2122 Test Method for Determining Dimensions of Ther-
3
composite pipe and fittings. moplastic Pipe and Fittings
1.2 This specification relates only to metal and plastic D 2837 Test Method for Obtaining Hydrostatic Design
3
composite pipes incorporating a welded metallic tube. The Basis for Thermoplastic Pipe Materials
welded metallic tube of itself is capable of sustaining internal D 3035 Specification for Polyethylene (PE) Plastic Pipe
3
pressures. Pipes consisting of metallic layers not welded (DR-PR) Based on Controlled Outside Diameter
together are outside the scope of this specification. D 3350 Specification for Polyethylene Plastics Pipe and
4
1.3 Specifications for connectors for use with pipe meeting Fittings Materials
5
the requirements of this specification are given in Annex A1. E 8 Test Methods for Tension Testing of Metallic Materials
3
1.4 This specification excludes crosslinked polyethylene- F 412 Terminology Relating to Plastic Piping Systems
aluminum-crosslinked polyethylene pipes (see Specification F 1281 Specification for Crosslinked Polyethylene/
F 1281). Aluminum/Crosslinked Polyethylene (PEX-AL-PEX)
3
1.5 The values stated in SI units are to be regarded as the Pressure Pipe
standard. The values given in parentheses are for information F 1974 Specification for Metal Insert Fittings for
only. Polyethylene/Aluminum/Polyethylene and Crosslinked
1.6 The following precautionary caveat pertains only to the Polyethylene/Aluminum/Crosslinked Polyethylene Com-
3
test methods portion, Section 9, of this specification: This posite Pressure Pipe
standard does not purport to address all of the safety concerns, 2.2 NSF Standard:
if any, associated with its use. It is the responsibility of the user Standard No. 14 Plastics Piping System Components and
6
of this standard to establish appropriate safety and health Related Materials
practices and determine the applicability of regulatory limita- Standard No. 61 Drinking Water System Components—
6
tions prior to use. Health Effects
2.3 Uniform Classification Committee Standard:
1 2
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Annual Book of ASTM Standards, Vol 08.01.
3
Piping Systems and is the direct responsibility of Subcommittee F17.11 on Annual Book of ASTM Standards, Vol 08.04.
4
Composite. Annual Book of ASTM Standards, Vol 08.02.
5
Current edition approved April 10, 2001. Published April 2001. Originally Annual Book of ASTM Standards, Vol 03.01.
6
published as F 1282 – 90. Last previous edition F 1282 – 00. Available from the NSF International, 789 Dixboro Rd., Ann Arbor, MI 48105.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1282
7
Uniform Freight Classification 5. Materia
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.