ASTM E2814-18

Standard Specification for Industrial Woven Wire Filter Cloth

SCOPE
1.1 This specification covers the special grade of industrial woven wire cloth, referred to as filter cloth, for general filtration including the separation of solids from fluids (liquids or gases), based on a desired particle size retention. Filter cloth can be made of any primary metal or metal alloy wire that is suitable for weaving.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2018
• ICS: 19.120 - Particle size analysis. Sieving
• Technical Committee: E29 - Particle and Spray Characterization
• Drafting Committee: E29.01 - Sieves, Sieving Methods, and Screening Media

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:E2814 −18
Standard Specification for
1
Industrial Woven Wire Filter Cloth
This standard is issued under the fixed designation E2814; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Industrial metal filter cloth is a special type of woven wire cloth that can be produced in many
specifications,oftenproprietaryinnature.SometimesreferredtoasDutchweaveorHollanderweave,
filter cloth can be woven in a variety of metals and is woven with a greater number of wires in one
direction than the other, and utilizing two different wire diameters. This specification covers woven
wire filter cloth for industrial use, which is commonly rated by its micron retention capability. Its
purpose is to introduce standard terms and definitions, to observe common technical considerations
that a user should be aware of, and to present alternative acceptance criteria based on a desired pore
size, or micron retention filtration rating. It should be noted this specification excludes standard
industrial woven wire cloth and sieve cloth from its scope, since these are covered under
Specifications E2016 and E11, respectively, as well as excludes plastic and synthetic filter cloth.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers the special grade of industrial
A478Specification for Chromium-Nickel Stainless Steel
woven wire cloth, referred to as filter cloth, for general
Weaving and Knitting Wire
filtration including the separation of solids from fluids (liquids
A555Specification for General Requirements for Stainless
orgases),basedonadesiredparticlesizeretention.Filtercloth
Steel Wire and Wire Rods
can be made of any primary metal or metal alloy wire that is
E11Specification forWovenWireTest Sieve Cloth andTest
suitable for weaving.
Sieves
1.2 Thevaluesstatedininch-poundunitsaretoberegarded
E1638Terminology Relating to Sieves, Sieving Methods,
as standard. The values given in parentheses are mathematical
and Screening Media
conversions to SI units that are provided for information only
E2016Specification for Industrial Woven Wire Cloth
3
and are not considered standard.
2.2 SAE Standards:
ARP-901Bubble-Point Test Method
1.3 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to establish appro-
3.1 Definitions:
priate safety, health, and environmental practices and deter-
3.1.1 For additional terminology, refer to Terminology
mine the applicability of regulatory limitations prior to use.
E1638.
1.4 This international standard was developed in accor-
3.1.2 bubble point test, n—a capillary flow test method that
dance with internationally recognized principles on standard-
measures the pressure required to force an air bubble through
ization established in the Decision on Principles for the
afilterclothsamplewettedunderatestliquidofknownsurface
Development of International Standards, Guides and Recom-
tension.
mendations issued by the World Trade Organization Technical
3.1.2.1 Discussion—The pressure is inversely proportional
Barriers to Trade (TBT) Committee.
to the pore size, should be standardized, and the pressure
1 2
ThisspecificationisunderthejurisdictionofASTMCommitteeE29onParticle For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and Spray Characterization and is the direct responsibility of Subcommittee E29.01 contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
on Sieves, Sieving Methods, and Screening Media. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2018. Published June 2018. Originally the ASTM website.
3
approved in 2011. Last previous edition approved in 2011 as E2814 – 11. DOI: AvailablefromSAEInternational(SAE),400CommonwealthDr.,Warrendale,
10.1520/E2814-18. PA 15096, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2814−18
observed at the first bubble point location is considered the 3.1.13.1 Discussion—The nominal rating may refer to: (1)
absolute rating. The test result pressure can be converted to a the glass bead or particle size the filter cloth will retain 90 %
calculated pore size or micron retention by applying a selected of by weight; (2) the bubble point pore size when the tenth
tortuosity factor. bubblelocationappears;or (3)thedegree
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E2814 − 11 E2814 − 18
Standard GuideSpecification for
1
Industrial Woven Wire Filter Cloth
This standard is issued under the fixed designation E2814; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Industrial metal filter cloth is a special type of woven wire cloth that can be produced in many
specifications, often proprietary in nature. Sometimes referred to as Dutch weave or Hollander weave,
filter cloth can be woven in a variety of metals and is woven with a greater number of wires in one
direction than the other, and utilizing two different wire diameters. This guidespecification covers
woven wire filter cloth for industrial use, which is commonly rated by its micron retention capability.
Its purpose is to introduce standard terms and definitions, to observe common technical considerations
that a user should be aware of, and to present a mathematical model that can be used to predict the
micron retention of a filter cloth specification. alternative acceptance criteria based on a desired pore
size, or micron retention filtration rating. It should be noted this guidespecification excludes standard
industrial woven wire cloth and sieve cloth from its scope, since these are covered under
Specifications E2016 and E11, respectively, as well as excludes plastic and synthetic filter cloth.
1. Scope
1.1 This guide covers the special grade of industrial woven wire cloth, referred to as filter cloth, for general filtration including
the separation of solids from fluids (liquids or gases), based on a desired particle size retention. Filter cloth can be made of any
primary metal or metal alloy wire that is suitable for weaving.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
E1638 Terminology Relating to Sieves, Sieving Methods, and Screening Media
E2016 Specification for Industrial Woven Wire Cloth
F316 Test Methods for Pore Size Characteristics of Membrane Filters by Bubble Point and Mean Flow Pore Test
3
2.2 SAE Standards:
ARP901 Bubble-Point Test Method
1
This guidespecification is under the jurisdiction of ASTM Committee E29 on Particle and Spray Characterization and is the direct responsibility of Subcommittee E29.01
on Sieves, Sieving Methods, and Screening Media.
Current edition approved April 1, 2011April 1, 2018. Published July 2011June 2018. Originally approved in 2011. Last previous edition approved in 2011 as E2814 – 11.
DOI: 10.1520/E2814-11.10.1520/E2814-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from SAE International (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001,15096, http://www.sae.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E2814 − 18
3. Terminology
3.1 Definitions:
3.1.1 For additional terminology, refer to Terminology E1638.
3.1.2 bubble point test, n—capillary flow bubble point methods are based on the fact that the pressure required to force an air
bubble through filter cloth wetted under a test liquid of known surface tension is inversely proportional to the pore size.
3.1.2.1 Discussion—
The pressure observed at the first bubble location is considered the absolute micron r
...