ASTM C1607-12
(Test Method)Standard Test Method for Determination of “Microwave Safe for Reheating” for Ceramicware
Standard Test Method for Determination of “Microwave Safe for Reheating” for Ceramicware
SIGNIFICANCE AND USE
This test is for evaluating ceramic products that are intended for reheating in a Consumer based microwave oven. It is not intended for evaluating products that will be used in commercial type microwaves.
This test method is not intended to evaluate metallic or polymeric based products.
Ceramic products intended for microwave use must also be evaluated for thermal shock resistance and pass the 325°F criteria as described in Test Method C554, before being tested for microwave safety. This would include specific tests for dinnerware, cookware, drinkware and ancillary items intended for use with hot foods, such as gravy boats or any product intended for microwave use.
Dishes having a metallic glaze, decoration or paint should not be used in this test or microwave ovens unless it is specifically designed for and marked as microwave safe.
SCOPE
1.1 This test method determines the suitability of ceramicware for use in microwave re-heating applications. Microwave ovens are mainly used for reheating and defrosting frozen foods. Severe thermal conditions can occur while reheating foods. Typical reheating of foods requires one to five min. in the microwave at the highest power settings. Longer periods than five minutes are considered cooking. Cooking test methods and standards are not addressed in this test method. Most ceramicware is minimally absorbing of the microwave energy and will not heat up significantly. Unfortunately there are some products that absorb microwave energy to a greater extent and can become very hot in the microwave and pose a serious hazard. Additionally, the nature of microwave heating introduces radiation in a non-uniform manner producing temperature differentials in the food being cooked as well as the ceramic container holding it. The differential may become great enough to thermal shock the ware and create dangerous conditions.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1607 − 12
StandardTest Method for
Determination of “Microwave Safe for Reheating” for
1
Ceramicware
This standard is issued under the fixed designation C1607; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 microwave safe for re-heating—ceramic products that
can be used in a microwave oven without any degradation,
1.1 This test method determines the suitability of ceram-
such as by deformation, fracturing, crazing, or heating up to
icware for use in microwave re-heating applications. Micro-
excessive temperatures.
waveovensaremainlyusedforreheatinganddefrostingfrozen
foods. Severe thermal conditions can occur while reheating
4. Summary of Test Method
foods. Typical reheating of foods requires one to five min. in
4.1 This method can be used to determine if a product is
the microwave at the highest power settings. Longer periods
safe to use for reheating foods in a microwave oven. The test
than five minutes are considered cooking. Cooking test meth-
emulates typical microwave use conditions.Temperature maxi-
ods and standards are not addressed in this test method. Most
mums and temperature differentials of products are determined
ceramicware is minimally absorbing of the microwave energy
after being subjected to microwave re-heating conditions.
and will not heat up significantly. Unfortunately there are some
products that absorb microwave energy to a greater extent and
5. Significance and Use
can become very hot in the microwave and pose a serious
hazard. Additionally, the nature of microwave heating intro-
5.1 This test is for evaluating ceramic products that are
duces radiation in a non-uniform manner producing tempera-
intended for reheating in a Consumer based microwave oven.
ture differentials in the food being cooked as well as the
It is not intended for evaluating products that will be used in
ceramic container holding it. The differential may become
commercial type microwaves.
great enough to thermal shock the ware and create dangerous
5.2 This test method is not intended to evaluate metallic or
conditions.
polymeric based products.
1.2 This standard does not purport to address all of the
5.3 Ceramic products intended for microwave use must also
safety concerns, if any, associated with its use. It is the
be evaluated for thermal shock resistance and pass the 325°F
responsibility of the user of this standard to establish appro-
criteria as described in Test Method C554, before being tested
priate safety and health practices and determine the applica-
for microwave safety. This would include specific tests for
bility of regulatory limitations prior to use.
dinnerware, cookware, drinkware and ancillary items intended
for use with hot foods, such as gravy boats or any product
2. Referenced Documents
intended for microwave use.
2
2.1 ASTM Standards:
5.4 Dishes having a metallic glaze, decoration or paint
C554 Test Method for Crazing Resistance of Fired Glazed
should not be used in this test or microwave ovens unless it is
Ceramic Whitewares by a Thermal Shock Method
specifically designed for and marked as microwave safe.
3. Terminology
6. Interferences
3.1 Definitions:
6.1 Test samples must be free from any obvious physical
defects.
1
This test method is under the jurisdiction ofASTM Committee C21 on Ceramic
7. Apparatus
Whitewares and Related Products and is the direct responsibility of Subcommittee
C21.03 on Methods for Whitewares and Environmental Concerns.
7.1 The microwave oven chosen for testing is based on its
Current edition approved April 1, 2012. Published April 2012. Originally
power level and being close to a mid-sized consumer product.
approved in 2006. Last previous edition approved in 2006 as C1607–06. DOI:
10.1520/C1607-12.
This is to provide a relatively high power density, which
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
creates conditions that are slightly harsher than conditions
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
found in the average microwave oven. The main difference
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. between microwave ovens is the power of the magnetron,
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1607 − 12
which generates the microwaves. Midsize and large ovens are possibility that the product attained temperatures that will
typically rated at 900 to 1300 watts and compact ovens have quickly
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C1607–06 Designation:C1607–12
Standard Test Method for
Determination of “Microwave Safe for Reheating” for
1
Ceramicware
This standard is issued under the fixed designation C1607; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method determines the suitability of ceramicware for use in microwave re-heating applications. Microwave ovens
are mainly used for reheating and defrosting frozen foods. Severe thermal conditions can occur while reheating foods. Typical
reheating of foods requires one to five min. in the microwave at the highest power settings. Longer periods than five minutes are
considered cooking. Cooking test methods and standards are not addressed in this test method. Most ceramicware is minimally
absorbingofthemicrowaveenergyandwillnotheatupsignificantly.Unfortunatelytherearesomeproductsthatabsorbmicrowave
energy to a greater extent and can become very hot in the microwave and pose a serious hazard. Additionally, the nature of
microwave heating introduces radiation in a non-uniform manner producing temperature differentials in the food being cooked as
well as the ceramic container holding it.The differential may become great enough to thermal shock the ware and create dangerous
conditions.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C554 Test Method for Crazing Resistance of Fired Glazed Ceramic Whitewares by a Thermal Shock Method
3. Terminology
3.1 Definition:
3.1.1 microwave safe for re-heating—ceramic products that can be used in a microwave oven without any degradation, such
as by deformation, fracturing, crazing, or heating up to excessive temperatures.
4. Summary of Test Method
4.1 This method can be used to determine if a product is safe to use for reheating foods in a microwave oven. The test emulates
typical microwave use conditions. Temperature maximums and temperature differentials of products are determined after being
subjected to microwave re-heating conditions.
5. Significance and Use
5.1 This test is for evaluating ceramic products that are intended for reheating in a Consumer based microwave oven. It is not
intended for evaluating products that will be used in commercial type microwaves.
5.2 This test method is not intended to evaluate metallic or polymeric based products.
5.3 Ceramic products intended for microwave use must also be evaluated for thermal shock resistance and pass the 325°F
criteria as described in Test Method C554, before being tested for microwave safety. This would include specific tests for
dinnerware, cookware, drinkware and ancillary items intended for use with hot foods, such as gravy boats or any product intended
for microwave use.
5.4 Disheshavingametallicglaze,decorationorpaintshouldnotbeusedinthistestormicrowaveovensunlessitisspecifically
designed for and marked as microwave safe.
1
ThistestmethodisunderthejurisdictionofASTMCommitteeC21onCeramicWhitewaresandRelatedProductsandisthedirectresponsibilityofSubcommitteeC21.03
on Methods for Whitewares and Environmental Concerns.
Current edition approved Feb. 15, 2006. Published March 2006. DOI: 10.1520/C1607-06.
Current edition approvedApril 1, 2012. PublishedApril 2012. Originally approved in 2006. Last previous edition approved in 2006 as C1607–06. DOI: 10.1520/C1607-12.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C1607–12
6. Interferences
6.1 Test samples must be free from any obvious physical defects.
7. Apparatus
7.1 The microwave oven chosen for testing is based on its power level and being close to a mid-sized consumer product. This
is to provide a relatively high power density, which creates conditions that are slightly harsher than cond
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.