ASTM F2152-07(2018)

Standard Guide for In-Situ Burning of Spilled Oil: Fire-Resistant Boom

ABSTRACT
This guide covers a set of criteria to evaluate the performance, material characteristics, and essential features of fire-resistant oil spill containment boom. Two types of fire-resistant oil containment Boom are covered: those that are intrinsically fire-resistant through the use of fire-resistant materials, and those that provide fire-resistance through the use of coolants. The boom shall be tested for operability, oil containment, and fire resistance.
SCOPE
1.1 This guide covers a set of criteria to evaluate the performance, material characteristics, and essential features of fire-resistant oil spill containment boom.  
1.2 This guide covers two types of fire-resistant oil containment boom: those that are intrinsically fire-resistant through the use of fire-resistant materials, and those that provide fire-resistance through the use of coolants. This guide may not be fully applicable to other types of fire-resistant boom.  
1.3 This guide is one of four related to in-situ burning of oil spills. Guide F1788 addresses environmental and operational considerations, Guide F1990 addresses ignition devices, and Guide F2230 addresses burning in ice conditions.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Sep-2018
• ICS: 13.220.50 - Fire-resistance of building materials and elements
• Technical Committee: F20 - Hazardous Substances and Oil Spill Response
• Drafting Committee: F20.15 - In-Situ Burning

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2152 − 07 (Reapproved 2018)
Standard Guide for
1
In-Situ Burning of Spilled Oil: Fire-Resistant Boom
This standard is issued under the fixed designation F2152; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F962 Specification for Oil Spill Response Boom Connec-
tion: Z-Connector
1.1 This guide covers a set of criteria to evaluate the
F1093 Test Methods for Tensile Strength Characteristics of
performance, material characteristics, and essential features of
Oil Spill Response Boom
fire-resistant oil spill containment boom.
F1523 Guide for Selection of Booms in Accordance With
1.2 This guide covers two types of fire-resistant oil contain-
Water Body Classifications
ment boom: those that are intrinsically fire-resistant through
F1788 Guide for In-Situ Burning of Oil Spills on Water:
the use of fire-resistant materials, and those that provide
Environmental and Operational Considerations
fire-resistance through the use of coolants. This guide may not
F1990 Guide for In-Situ Burning of Spilled Oil: Ignition
be fully applicable to other types of fire-resistant boom.
Devices
1.3 This guide is one of four related to in-situ burning of oil F2084 Guide for Collecting Containment Boom Perfor-
mance Data in Controlled Environments
spills. Guide F1788 addresses environmental and operational
considerations, Guide F1990 addresses ignition devices, and F2230 Guide for In-situ Burning of Oil Spills on Water: Ice
Conditions
Guide F2230 addresses burning in ice conditions.
1.4 This standard does not purport to address all of the
3. Terminology
safety concerns, if any, associated with its use. It is the
3.1 Definitions of Terms Specific to This Standard:
responsibility of the user of this standard to establish appro-
3.1.1 actively-cooled fire-resistant boom—type of fire-
priate safety, health, and environmental practices and deter-
resistant boom that uses ancillary equipment to supply coolant
mine the applicability of regulatory limitations prior to use.
to the boom to increase its fire resistance.
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
3.1.2 ancillary equipment—mechanical devices essential to
ization established in the Decision on Principles for the
the operation of a given boom system; for example, water
Development of International Standards, Guides and Recom-
pumps, power supplies, control manifolds, and so forth.
mendations issued by the World Trade Organization Technical
3.1.3 fire resistance—the ability of a barrier to maintain
Barriers to Trade (TBT) Committee.
structural integrity and oil containment ability while being
subjected to the thermal stress of a petroleum fire.
2. Referenced Documents
3.1.4 fire-resistant boom—barrier intended for containment
2
2.1 ASTM Standards:
of burning oil floating on water.
F625 Practice for Classifying Water Bodies for Spill Control
3.1.5 freeboard—minimum vertical height of the boom
Systems
above the water line.
F715 Test Methods for Coated Fabrics Used for Oil Spill
Control and Storage
3.1.6 heat flux—the thermal intensity indicated by the
2
F818 Terminology Relating to Spill Response Booms and amount of energy per unit area. (kW/m ).
Barriers
3.1.7 in-situ burning—burning of oil directly on the water
surface.
1 3.1.8 residue—the material, excluding airborne emissions,
This guide is under the jurisdiction of ASTM Committee F20 on Hazardous
Substances and Oil Spill Response and is the direct responsibility of Subcommittee remaining after the oil stops burning.
F20.15 on In-Situ Burning.
3.1.8.1 Discussion—Residue includes only material derived
Current edition approved Oct. 1, 2018. Published March 2019. Originally
from the oil that is burned, and it shall not include material
approved in 2001. Last previous edition approved in 2013 as F2152 – 07(2013).
related to the boom or its components.
DOI: 10.1520/F2152-07R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3.1.9 salvageable components—components of the boom
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
that may be reused in a repair or reconstruction of the boom to
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. its original state.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2152 − 07 (2018)
TABLE 1 Minimum Design Values for Fire-Resistant Boom
3.2 For other definitions relating to boom properties and
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2152 − 07 (Reapproved 2013) F2152 − 07 (Reapproved 2018)
Standard Guide for
1
In-Situ Burning of Spilled Oil: Fire-Resistant Boom
This standard is issued under the fixed designation F2152; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide covers a set of criteria to evaluate the performance, material characteristics, and essential features of fire-resistant
oil spill containment boom.
1.2 This guide covers two types of fire-resistant oil containment boom: those that are intrinsically fire-resistant through the use
of fire-resistant materials, and those that provide fire-resistance through the use of coolants. This guide may not be fully applicable
to other types of fire-resistant boom.
1.3 This guide is one of four related to in-situ burning of oil spills. Guide F1788 addresses environmental and operational
considerations, Guide F1990 addresses ignition devices, and Guide F2230 addresses burning in ice conditions.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory requirementslimitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
F625 Practice for Classifying Water Bodies for Spill Control Systems
F715 Test Methods for Coated Fabrics Used for Oil Spill Control and Storage
F818 Terminology Relating to Spill Response Booms and Barriers
F962 Specification for Oil Spill Response Boom Connection: Z-Connector
F1093 Test Methods for Tensile Strength Characteristics of Oil Spill Response Boom
F1523 Guide for Selection of Booms in Accordance With Water Body Classifications
F1788 Guide for In-Situ Burning of Oil Spills on Water: Environmental and Operational Considerations
F1990 Guide for In-Situ Burning of Spilled Oil: Ignition Devices
F2084 Guide for Collecting Containment Boom Performance Data in Controlled Environments
F2230 Guide for In-situ Burning of Oil Spills on Water: Ice Conditions
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 actively-cooled fire-resistant boom—type of fire-resistant boom that uses ancillary equipment to supply coolant to the
boom to increase its fire resistance.
3.1.2 ancillary equipment—mechanical devices essential to the operation of a given boom system; for example, water pumps,
power supplies, control manifolds, and so forth.
3.1.3 fire resistance—the ability of a barrier to maintain structural integrity and oil containment ability while being subjected
to the thermal stress of a petroleum fire.
1
This guide is under the jurisdiction of ASTM Committee F20 on Hazardous Substances and Oil Spill Response and is the direct responsibility of Subcommittee F20.15
on In-Situ Burning.
Current edition approved April 1, 2013Oct. 1, 2018. Published July 2013March 2019. Originally approved in 2001. Last previous edition approved in 20072013 as
F2152 – 07.F2152 – 07(2013). DOI: 10.1520/F2152-07R13.10.1520/F2152-07R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2152 − 07 (2018)
3.1.4 fire-resistant boom—barrier intended for containment of burning oil floating on water.
3.1.5 freeboard—minimum vertical height of the boom above the water line.
2
3.1.6 heat flux—the thermal intensity indicated by the amount of energy per unit area. (kW/m ).
3.1.7 in-situ burning—burning of oil directly on the water surface.
3.1.8 residue—the material, excluding airborne emissions, remaining after the oil stops burning.
3.1.8.1 Discussion—
Residue inclu
...