ASTM F2599-20

Standard Practice for Sectional Repair of Damaged Pipe By Means of an Inverted Cured-In-Place Liner<rangeref></rangeref >

SIGNIFICANCE AND USE
4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of pipes through the use of a resin-impregnated tube installed within a damaged existing host pipe. As for any practice, modifications may be required for specific job conditions.
SCOPE
1.1 This practice covers requirements and test methods for the sectional cured-in-place lining (SCIPL) repair of a pipe line (4 in. through 60 in. (10.2 cm through 152 cm)) by the installation of a continuous resin-impregnated-textile tube into an existing host pipe by means of air or water inversion and inflation. The tube is pressed against the host pipe by air or water pressure and held in place until the thermoset resins have cured. When cured, the sectional liner shall extend over a predetermined length of the host pipe as a continuous, one piece, tight fitting, corrosion resistant, and verifiable non-leaking cured-in-place pipe.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 There is no similar or equivalent ISO Standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 29-Feb-2020
• ICS: 23.040.99 - Other pipeline components
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.67 - Trenchless Plastic Pipeline Technology

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2599 − 20
Standard Practice for
Sectional Repair of Damaged Pipe By Means of an Inverted
1,2
Cured-In-Place Liner
This standard is issued under the fixed designation F2599; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
1.1 This practice covers requirements and test methods for
thesectionalcured-in-placelining(SCIPL)repairofapipeline
2. Referenced Documents
(4 in. through 60 in. (10.2 cm through 152 cm)) by the
3
2.1 ASTM Standards:
installation of a continuous resin-impregnated-textile tube into
D790 Test Methods for Flexural Properties of Unreinforced
an existing host pipe by means of air or water inversion and
and Reinforced Plastics and Electrical Insulating Materi-
inflation. The tube is pressed against the host pipe by air or
als
waterpressureandheldinplaceuntilthethermosetresinshave
D1149 Test Methods for Rubber Deterioration—Cracking in
cured. When cured, the sectional liner shall extend over a
an Ozone Controlled Environment
predetermined length of the host pipe as a continuous, one
D1600 TerminologyforAbbreviatedTermsRelatingtoPlas-
piece, tight fitting, corrosion resistant, and verifiable non-
tics
leaking cured-in-place pipe.
D2990 Test Methods for Tensile, Compressive, and Flexural
1.2 The values stated in inch-pound units are to be regarded
Creep and Creep-Rupture of Plastics
as standard. The values given in parentheses are mathematical
D3681 TestMethodforChemicalResistanceof“Fiberglass”
conversions to SI units that are provided for information only
(Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a
and are not considered standard.
Deflected Condition
D5813 Specification for Cured-In-Place Thermosetting
1.3 There is no similar or equivalent ISO Standard.
Resin Sewer Piping Systems
1.4 This standard does not purport to address all of the
F412 Terminology Relating to Plastic Piping Systems
safety concerns, if any, associated with its use. It is the
F1216 Practice for Rehabilitation of Existing Pipelines and
responsibility of the user of this standard to establish appro-
Conduits by the Inversion and Curing of a Resin-
priate safety, health, and environmental practices and deter-
Impregnated Tube
mine the applicability of regulatory limitations prior to use.
F3240 Practice for Installation of Seamless Molded Hydro-
1.5 This international standard was developed in accor-
philic Gaskets (SMHG) for Long-Term Watertightness of
dance with internationally recognized principles on standard-
Cured-in-Place Rehabilitation of Main and Lateral Pipe-
ization established in the Decision on Principles for the
lines
Development of International Standards, Guides and Recom- 4
2.2 NASSCO Guidelines:
Recommended Specifications for Sewer Collection System
Rehabilitation.
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.67 on
3. Terminology
Trenchless Plastic Pipeline Technology.
3.1 Definitions:
Current edition approved March 1, 2020. Published April 2020. Originally
approved in 2006. Last previous edition approved in 2016 as F2599–16. DOI:
3.1.1 Unless otherwise indicated, definitions are in accor-
10.1520/F2599-20.
dance with Terminology F412, and abbreviations are in accor-
2
The sectional repair of damaged pipe by means of inversion of a cured in place
dance with Terminology D1600.
liner is covered by patents The sectional repair of damaged pipe by means of
inversion of a cured in place liner is covered by patents 6,994,118, 7,975,726,
8,240,340,8,240,341,8,567,451,8,636,036,8,651,145,8,667,991,8,678,037,8,689,
3
835, 9,169,957, 9,366,375, 9,562,339, 9,551,449 (LMK Enterprises, Inc. 1779 For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Chessie Lane, Ottawa, IL 61350). Interested parties are invited to submit informa- contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
tionregardingtheidentificationofacceptablealternativestothispatenteditemtothe Standards volume information, refer to the standard’s Document Summary page on
Committee on Standards, ASTM Headquarters, 100 Barr Harbor Drive, West the ASTM website.
4
Conshohocken, PA 19428-2959. Your comments will receive careful consideration Available from 5285 Westview Drive Suite 202 Frederick, MD 21703,
at a meeting of the responsible technical committee which you may attend. http://www.nassco.org
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2599 − 16 F2599 − 20
Standard Practice for
The Sectional Repair of Damaged Pipe By Means of Anan
1,2
Inverted Cured-In-Place Liner
This standard is issued under the fixed designation F2599; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This practice covers requirements and test methods for the sectional cured-in-place lining (SCIPL) repair of a pipe line (4
in. through 60 in. (10.2 cm through 152 cm)) by the installation of a continuous resin-impregnated-textile tube into an existing host
pipe by means of air or water inversion and inflation. The tube is pressed against the host pipe by air or water pressure and held
in place until the thermoset resins have cured. When cured, the sectional liner shall extend over a predetermined length of the host
pipe as a continuous, one piece, tight fitting, corrosion resistant, and verifiable non-leaking cured-in-place pipe.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 There is no similar or equivalent ISO Standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. Particular attention is drawn to those safety regulations and requirements
involving entering into and working in confined spaces.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
D1149 Test Methods for Rubber Deterioration—Cracking in an Ozone Controlled Environment
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2990 Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
D3681 Test Method for Chemical Resistance of “Fiberglass” (Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a Deflected
Condition
D5813 Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
F412 Terminology Relating to Plastic Piping Systems
F1216 Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
F3240 Practice for Installation of Seamless Molded Hydrophilic Gaskets (SMHG) for Long-Term Watertightness of
Cured-in-Place Rehabilitation of Main and Lateral Pipelines
1
This practice is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.67 on Trenchless Plastic
Pipeline Technology.
Current edition approved April 1, 2016March 1, 2020. Published May 2016April 2020. Originally approved in 2006. Last previous edition approved in 20112016 as
F2599–11.–16. DOI: 10.1520/F2599-16.10.1520/F2599-20.
2
The sectional repair of damaged pipe by means of inversion of a cured in place liner is covered by patents The sectional repair of damaged pipe by means of inversion
of a cured in place liner is covered by patents 6,994,118, 7,975,726, 8,240,340, 8,240,341,8,567,451, 8,636,036, 8,651,145, 8,667,991, 8,678,037, 8,689,835, 9,169,957,
9,366,375, 9,562,339, 9,551,449 (LMK Enterprises, Inc. 1779 Chessie Lane, Ottawa, IL 61350). Interested parties are invited to submit information regarding the identification
of acceptable alternatives to this patented item to the Committee on Standards, ASTM Headquarters, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. Your
comments will receive careful consideration at a meeting of the responsible technical committee which you may attend.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Docum
...