ASTM F952-08

Standard Specification for Mixing Machines, Food, Electric

ABSTRACT
This specification covers vertical electric food mixing machines in a certain size range (as expressed by bowl capacity). These machines shall be adaptable for mixing, whipping, and beating food products. Optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine are also discussed. These machines shall consists of the following parts, equipment, and accessories: electric drive motor, speed selector, beater shaft, power supply, mixing bowls, agitators, bowl lift, bowl support, base, timer, attachment hub, and bowl truck. Optional equipments for these machines may include mixing bowl extension, bowl adapters, splash covers, and table. In order to determine the mixing machines' overall performance, the following tests shall be done: operational test, speed test, power bowl lift test and run-in test.
SCOPE
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5 to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include special purpose machines that are intended solely for mixing dough.
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Mar-2008
• ICS: 97.040.50 - Small kitchen appliances
• Technical Committee: F26 - Food Service Equipment
• Drafting Committee: F26.04 - Mechanical Preparation Equipment

Relations

• Replaces: ASTM F952-03 - Standard Specification for Mixing Machines, Food, Electric
• Effective Date: 01-Apr-2008
• Replaced By: ASTM F952-12 - Standard Specification for Mixing Machines, Food, Electric
• Effective Date: 01-Nov-2012

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F952 −08 AnAmerican National Standard
Standard Specification for
1
Mixing Machines, Food, Electric
ThisstandardisissuedunderthefixeddesignationF952;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
3
1. Scope 2.2 NSF/ANSI Standards:
NSF/ANSI No. 2 Food Equipment
1.1 This specification covers vertical electric food mixing
NSF/ANSI No. 8 Commercial Powered Food Preparation
machines in the size range (as expressed by bowl capacity)
Equipment
from 5 to 140 qt. These machines shall be adaptable for
NSF Food Equipment Listing (Current Year)
mixing, whipping, and beating food products. This specifica-
4
2.3 Underwriters Laboratories Standards:
tion does not include special purpose machines that are
ANSI/UL 763 Motor-Operated Commercial Food Preparing
intended solely for mixing dough.
Machines
1.2 This specification also covers optional construction
ANSI/UL 969 Marking and Labeling Systems
features and attachments that enhance the mixing, beating, or
5
2.4 ANSI Standards:
whipping capabilities of the machine. This specification does
ANSI Z1.4 Sampling Procedures and Tables for Inspection
not cover ancillary equipment that can be driven by the
by Attributes
attachment hub.
ANSI S1.13 Methods for Measurement of Sound Pressure
1.3 The values stated in inch-pound units are to be regarded
Levels
as standard. No other units of measurement are included in this 6
2.5 Military Standards:
standard.
MIL-STD-1399/300 Interface Standard for Shipboard
1.4 The following precautionary caveat pertains only to the
Systems, Section 300A, Electric Power, Alternating Cur-
test methods portion, Section 9, of this specification. This rent
standard does not purport to address all of the safety concerns,
MIL-STD-167/1 Mechanical Vibration of Shipboard Equip-
if any, associated with its use. It is the responsibility of the user
ment (Type I—Environmental and Type II—Internally
of this standard to establish appropriate safety and health
Excited)
practices and determine the applicability of regulatory limita-
MIL-STD-461 Requirements for the Control of Electromag-
tions prior to use.
netic Interference Characteristics of Subsystems and
Equipment
2. Referenced Documents
2
3. Terminology
2.1 ASTM Standards:
D3951 Practice for Commercial Packaging
3.1 Definitions of Terms Specific to This Standard:
F760 Specification for Food Service Equipment Manuals
3.1.1 agitators, n—these devices attach to the vertical shaft
F1166 Practice for Human Engineering Design for Marine
that protrudes downward from the mixer and converts the
Systems, Equipment, and Facilities
planetary rotation into the desired action on the foodstuffs
within the bowl.
1
This specification is under the jurisdiction of ASTM Committee F26 on Food
Service Equipment and is the direct responsibility of Subcommittee F26.04 on
3
Mechanical Preparation Equipment. Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
Current edition approved April 1, 2008. Published April 2008. Originally Arbor, MI 48113-0140, http://www.nsf.org.
4
approved in 1985. Last previous edition approved in 2003 as F952 – 03. DOI: Available from comm2000, 1414 Brook Dr., Downers Grove, IL 60515.
5
10.1520/F0952-08. Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 4th Floor, New York, NY 10036, http://www.ansi.org.
6
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
Standards volume information, refer to the standard’s Document Summary page on Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
the ASTM website. www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F952 − 08
3.1.2 attachment hub, n—the device that locks ancillary 6. Physical Requirements
devices, such as a vegetable slicer or a chopping end, into an
6.1 Design and Manufacture—The mixer shall meet the
industry standard #12 tapered hub (#10 tapered hub for Size 5
then current applicable requirements of NSF/ANSI No. 8 and
machines) and provides a rotating square drive. This is
ANSI/UL 763. Accessories, such as agitators, bowl trucks,
mounted above the bowl on the front of the mixer.
bowls, tables, extensions, adapters, splash covers, and storage
3.1.3 bowl guard, n—the barrier, assembled over the bowl
stands sh
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:F952–03 Designation: F 952 – 08
Standard Specification for
1
Mixing Machines, Food, Electric
This standard is issued under the fixed designation F 952; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers vertical electric food mixing machines in the size range (as expressed by bowl capacity) from 5
to 140 qt. These machines shall be adaptable for mixing, whipping, and beating food products. This specification does not include
special purpose machines that are intended solely for mixing dough.
1.2 This specification also covers optional construction features and attachments that enhance the mixing, beating, or whipping
capabilities of the machine. This specification does not cover ancillary equipment that can be driven by the attachment hub.
1.3The values stated in inch-pound units are to be regarded as the standard.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this
standard.
1.4 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D 3951 Practice for Commercial Packaging
F 760 Specification for Food Service Equipment Manuals
F 1166 Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities
3
2.2 NSF/ANSI Standards:
NSF/ANSI No. 2 Food Equipment
NSF/ANSI No. 8 Commercial Powered Food Preparation Equipment Commercial Powered Food Preparation Equipment
NSF Food Equipment Listing (Current Year)
4
2.3 Underwriters Laboratories Standards: Underwriters Laboratories Standards:
ANSI/UL 763 Motor-Operated Commercial Food Preparing Machines
ANSI/UL 969 Marking and Labeling Systems
5
2.4 ANSI Standards: ANSI Standards:
Z1.4ANSI Z1.4 Sampling Procedures and Tables for Inspection by Attributes
ANSI S1.13 Methods for Measurement of Sound Pressure Levels
6
2.5 Military Standards: Military Standards:
MIL-STD-1399/300 Interface Standard for Shipboard Systems, Section 300A, Electric Power, Alternating Current
MIL-STD-167/1 Mechanical Vibration of Shipboard Equipment (Type I—Environmental and Type II—Internally Excited)
MIL-STD-461 Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment
1
This specification is under the jurisdiction ofASTM Committee F26 on Food Service Equipment and is the direct responsibility of Subcommittee F26.04 on Mechanical
Preparation Equipment.
Current edition approved Sept. 10, 2003. Published September 2003. Originally approved in 1985. Last previous edition approved in 1999 as F952–99.
Current edition approved April 1, 2008. Published April 2008. Originally approved in 1985. Last previous edition approved in 2003 as F 952 – 03.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 15.09.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 15.08.
3
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
4
Annual Book of ASTM Standards, Vol 01.07.
4
Available from comm2000, 1414 Brook Dr., Downers Grove, IL 60515.
5
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140.
5
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
6
Available from comm2000, 1414 Brook Dr., Downers Grove, IL 60515.
6
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F952–
...