ASTM D7633-13(2022)

Standard Test Method for Carbon Black—Carbon Content

SIGNIFICANCE AND USE
4.1 The total carbon content of a carbon black is a requirement for the calculation and reporting of carbon dioxide emissions. It can also be used in calculations to estimate yield of the process.
SCOPE
1.1 This test method covers the instrumental determination of carbon content in a carbon black sample. Values obtained represent the total carbon content.  
1.2 The method is applicable to tread, carcass and specialty type carbon blacks obtained from partial combustion or thermal decomposition processes, which typically contain 95 to 100 % carbon.  
1.3 The results of these tests can be expressed as mass % carbon.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 31-May-2022
• ICS: 71.060.10 - Chemical elements
• Technical Committee: D24 - Carbon Black
• Drafting Committee: D24.66 - Environment, Health, and Safety

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D7633 − 13 (Reapproved 2022)
Standard Test Method for
1
Carbon Black—Carbon Content
This standard is issued under the fixed designation D7633; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Standards in the Rubber and Carbon Black Manufacturing
Industries
1.1 This test method covers the instrumental determination
of carbon content in a carbon black sample. Values obtained
3. Summary of Test Method
represent the total carbon content.
3.1 In this test method, a sample is weighed in a combustion
1.2 The method is applicable to tread, carcass and specialty
boat and the carbon content is determined by placing the boat
type carbon blacks obtained from partial combustion or ther-
in a tube furnace operating at 1350°C in a stream of oxygen
mal decomposition processes, which typically contain 95 to
resulting in complete combustion. Carbon in the sample is
100 % carbon.
oxidized to carbon dioxide. Moisture and particulates are
1.3 The results of these tests can be expressed as mass %
removed from the gas stream by traps filled with anhydrous
carbon.
magnesium perchlorate. The gas stream is then passed through
1.4 The values stated in SI units are to be regarded as a cell in which carbon dioxide concentration is measured by an
standard. No other units of measurement are included in this infrared (IR) absorption detector at a precise wavelength in the
standard. IR spectrum.
1.5 This standard does not purport to address all of the
3.2 This test method is for use with commercially available
safety concerns, if any, associated with its use. It is the
carbon analyzers equipped to carry out the combustion and
responsibility of the user of this standard to establish appro-
measurement operations automatically.
priate safety, health, and environmental practices and deter-
3.3 The carbon analyzer must be calibrated using an appro-
mine the applicability of regulatory limitations prior to use.
priate calibration standard (see 6.4).
1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
4. Significance and Use
ization established in the Decision on Principles for the
4.1 The total carbon content of a carbon black is a require-
Development of International Standards, Guides and Recom-
ment for the calculation and reporting of carbon dioxide
mendations issued by the World Trade Organization Technical
emissions. It can also be used in calculations to estimate yield
Barriers to Trade (TBT) Committee.
of the process.
2. Referenced Documents
5. Apparatus
2
2.1 ASTM Standards:
5.1 Analytical Balance,orequivalent,capableofaweighing
D1799 Practice for Carbon Black—Sampling Packaged
sensitivity of 1 mg or better resolution.
Shipments
D1900 Practice for Carbon Black—Sampling Bulk Ship-
5.2 Gravity Convection Drying Oven, capable of maintain-
ments
ing 125 6 5°C.
D4483 Practice for Evaluating Precision for Test Method
5.3 Measurement Apparatus, equipped to automatically
combust the sample and measure carbon content.
5.4 Combustion tube and boat made of a suitable material
1
This test method is under the jurisdiction ofASTM Committee D24 on Carbon
such as mullite, porcelain or zircon.
Black and is the direct responsibility of Subcommittee D24.66 on Environment,
Health, and Safety.
CurrenteditionapprovedJune1,2022.PublishedJuly2022.Originallyapproved
6. Reagents
in 2010. Last previous edition approved in 2018 as D7633 – 13 (2018). DOI:
10.1520/D7633-13R22.
6.1 Purity of Reagents—Reagent grade chemicals shall be
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
used in all tests. Unless otherwise indicated, it is intended that
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
all reagents shall conform to the specifications of the Commit-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. tee onAnalytical Reagents of theAmerican Chemical Society,
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D7633 − 13 (2022)
3
where such specifications are available. Other grades may be 10.4 Weigh approximately 0.1 g of the sample or use
used, provided it is first ascertained that the reagent is of recommended mass per manufacturer.
sufficiently high purity to permit its use without lessening the
...