ASTM B584-04

Standard Specification for Copper Alloy Sand Castings for General Applications

SCOPE
1.1 This specification covers requirements for copper alloy sand castings for general applications. Nominal compositions of the alloys defined by this specification are shown in Table 1. This is a composite specification replacing former documents as shown in Table 1.
Note 1—Other copper alloy castings are included in the following ASTM specifications: B 22, B 61, B 62, B 66, B 67, B 148, B 176, B 271, B 369, B 427, B 492, B 505/B 505M, B 763, B 770, and B 806.
1.2 Component part castings produced to this specification may be manufactured in advance and supplied from stock. In such cases the manufacturer shall maintain a general quality certification of all castings without specific record or date of casting for a specific casting.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

General Information

• Status: Historical
• Publication Date: 30-Jun-2004
• ICS: 77.150.30 - Copper products
• Technical Committee: B05 - Copper and Copper Alloys
• Drafting Committee: B05.05 - Castings and Ingots for Remelting

Relations

• Replaces: ASTM B584-00 - Standard Specification for Copper Alloy Sand Castings for General Applications
• Effective Date: 01-Jul-2004
• Replaced By: ASTM B584-05 - Standard Specification for Copper Alloy Sand Castings for General Applications
• Effective Date: 01-Nov-2005
• Referred By: ASTM F2929-17(2021) - Standard Specification for Crosslinked Polyethylene (PEX) Tubing of 0.070 in. Wall and Fittings for Radiant Heating Systems up to 75 psig
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1511-18(2023) - Standard Specification for Mechanical Seals for Shipboard Pump Applications
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1974-23 - Standard Specification for Metal Insert Fittings for Polyethylene/Aluminum/Polyethylene and Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene Composite Pressure Pipe
• Effective Date: 01-Jul-2004
• Referred By: ASTM F3347-23 - Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
• Effective Date: 01-Jul-2004
• Referred By: ASTM F3226/F3226M-19 - Standard Specification for Metallic Press-Connect Fittings for Piping and Tubing Systems
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1510-21 - Standard Specification for Rotary Positive Displacement Pumps, Ships Use
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1718-01(2019) - Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps
• Effective Date: 01-Jul-2004
• Referred By: ASTM B30-23 - Standard Specification for Copper Alloys in Ingot and Other Remelt Forms
• Effective Date: 01-Jul-2004
• Referred By: ASTM F998-12(2022) - Standard Specification for Centrifugal Pump, Shipboard Use
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1548-01(2023) - Standard Specification for Performance of Fittings for Use with Gasketed Mechanical Couplings Used in Piping Applications
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1245-19 - Standard Specification for Faucets, Single and Double, Compression and Self-Closing Type, Shipboard
• Effective Date: 01-Jul-2004
• Referred By: ASTM F2798-09(2023) - Standard Specification for Sealless Lube Oil Pump with Oil Through Motor for Marine Applications
• Effective Date: 01-Jul-2004
• Referred By: ASTM F1807-23 - Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps, for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing
• Effective Date: 01-Jul-2004

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 584 – 04
Standard Specification for
1
Copper Alloy Sand Castings for General Applications
This standard is issued under the fixed designation B 584; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* B 176 Specification for Copper-Alloy Die Castings
B 208 Practice for Preparing Tension Test Specimens for
1.1 This specification covers requirements for copper alloy
Copper Alloy Sand, Permanent Mold, Centrifugal, and
sand castings for general applications. Nominal compositions
Continuous Castings
of the alloys defined by this specification are shown in Table
2
B 271 Specification for Copper-Base Alloy Centrifugal
1. This is a composite specification replacing former docu-
Castings
ments as shown in Table 1.
B 369 Specification for Copper-Nickel Alloy Castings
NOTE 1—Other copper alloy castings are included in the following
B 427 Specification for Gear Bronze Alloy Castings
ASTM specifications:B22,B61,B62,B66,B67, B 148, B 176, B 271,
B 492 Specification for Cast Copper-Nickel Ship Tailshaft
B 369, B 427, B 492, B 505/B 505M, B 763, B 770, and B 806.
4
Sleeves
1.2 Component part castings produced to this specification
B 505/B 505M Specification for Copper-Base Alloy Con-
may be manufactured in advance and supplied from stock. In
tinuous Castings
such cases the manufacturer shall maintain a general quality
B 763 Specification for Copper Alloy Sand Castings for
certification of all castings without specific record or date of
Valve Application
casting for a specific casting.
B 770 Specification for Copper-BerylliumAlloy Sand Cast-
1.3 The values stated in inch-pound units are to be regarded
ings for General Applications
as the standard. The values given in parentheses are provided
B 806 Specification for Copper Alloy Permanent Mold
for information purposes only.
Castings for General Applications
B 824 Specification for General Requirements for Copper
2. Referenced Documents
Alloy Castings
3
2.1 ASTM Standards:
B 846 Terminology for Copper and Copper Alloys
B22 Specification for Bronze Castings for Bridges and
E 255 Practice for Sampling Copper and CopperAlloys for
Turntables
the Determination of Chemical Composition
B61 Specification for Steam or Valve Bronze Castings
E 527 Practice for Numbering Metals and Alloys (UNS)
B62 Specification for Composition Bronze or Ounce Metal
2.2 ASME Code:
Castings 5
ASME Boiler and Pressure Vessel Code
B66 Specification for Bronze Castings for Steam Locomo-
tive Wearing Parts 3. Terminology
B67 Specification for Car and Tender Journal Bearings,
3.1 Definitions of terms relating to copper alloys can be
4
Lined
found in Terminology B 846.
B 148 Specification for Aluminum-Bronze Sand Castings
4. General Requirements
4.1 The following sections of Specification B 824 form a
1
ThisspecificationisunderthejurisdictionofASTMCommitteeB05onCopper
part of this specification. In the event of a conflict between this
and Copper Alloys and is the direct responsibility of Subcommittee B05.05 on
specification and Specification B 824, the requirements of this
Castings and Ingots for Remelting.
Current edition approved July 1, 2004. Published July 2004. Originally approved
specification shall take precedence.
in 1973. Last previous edition approved in 2000 as B 584 – 00.
4.1.1 Terminology,
2
The UNS system for copper and copper alloys (see Practice E 527) is a simple
4.1.2 Other Requirements,
expansion of the former standard designation system accomplished by the addition
of a prefix “C” and a suffix “00”. The suffix can be used to accommodate 4.1.3 Dimensions, Mass, and Permissible Variations,
composition variations of the base alloy.
4.1.4 Workmanship, Finish, and Appearance,
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
5
the ASTM website. Available from American Society of Mechanical Engineers (ASME), ASME
4
Withdrawn. International Headquarters, Three Park Ave., New York, NY 10016-5990.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B584–04
TABLE 1 Nominal Compositions
Copper
Alloy Previous Alum- Man- Sili- Nio- Bis-
Classification Commercial Designation Copper Tin Lead Zinc Nickel Iron
UNS Designation inumganese con bium muth
No.
1 1
Leaded red br
...