Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength

SCOPE
1.1 This specification covers two types of quenched and tempered, alloy steel, heavy hex structural bolts having a tensile strength of 150 to 173 ksi.
1.2 These bolts are intended for use in structural connections. These connections are covered under the requirements of the Specification for Structural Joints Using Specification A 325 or A 490 bolts, approved by the Research Council on Structural Connections; endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.
1.3 The bolts are furnished in sizes 1/2 to 1 ½ in., inclusive. They are designated by type denoting chemical composition as follows:TypeDescriptionType 1Medium carbon alloy steelType 2Withdrawn in 2002Type 3Weathering steel
1.4 This specification provides that heavy hex structural bolts shall be furnished unless other dimensional requirements are specified on the purchase order.
1.5 Terms used in this specification are defined in Specification F 1789 unless otherwise defined herein.
1.6 For metric bolts, see Specification A 490M Classes 10.9 and 10.9.3
1.7 The following safety hazards caveat pertains only to the Test Methods portion, Section 1412 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jul-2004
Technical Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A490-04a - Standard Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
American Association State
Designation: A 490 – 04a Highway and Transportation
Officials Standard
AASHTO No.: M 253
Standard Specification for
Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum
1
Tensile Strength
This standard is issued under the fixed designation A 490; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 2. Referenced Documents
3
1.1 This specification covers two types of quenched and 2.1 ASTM Standards:
tempered, alloy steel, heavy hex structural bolts having a A 194/A 194M Specification for Carbon and Alloy Steel
tensile strength of 150 to 173 ksi. Nuts for Bolts for High-Pressure and High-Temperature
1.2 These bolts are intended for use in structural connec- Service
tions.These connections are covered under the requirements of A 325 Specification for Structural Bolts, Steel, Heat
the Specification for Structural Joints Using Specification Treated, 120/105 ksi Minimum Tensile Strength
A 325 or A 490 bolts, approved by the Research Council on A 354 Specification for Quenched and Tempered Alloy
Structural Connections; endorsed by the American Institute of Steel Bolts, Studs, and Other Externally Threaded Fasten-
2
Steel Construction and by the Industrial Fastener Institute. ers
1 1
1.3 The bolts are furnished in sizes ⁄2 to 1 ⁄2 in., inclusive. A 490M Specification for High-Strength Steel Bolts,
They are designated by type denoting chemical composition as Classes10.9and10.9.3,forStructuralSteelJoints[Metric]
follows: A 563 Specification for Carbon and Alloy Steel Nuts
A 751 Test Methods, Practices, and Terminology for
Type Description
Chemical Analysis of Steel Products
Type 1 Medium carbon alloy steel
D 3951 Practice for Commercial Packaging
Type 2 Withdrawn in 2002
Type 3 Weathering steel E 384 Test Method for Microindentationhardness of Mate-
rials
1.4 This specification provides that heavy hex structural
E 709 Guide for Magnetic Particle Examination
bolts shall be furnished unless other dimensional requirements
E 1444 Practice for Magnetic Particle Inspection
are specified on the purchase order.
F 436 Specification for Hardened Steel Washers
1.5 Terms used in this specification are defined in Termi-
F 606 Test Methods for Determining the Mechanical Prop-
nology F 1789 unless otherwise defined herein.
erties of Externally and Internally Threaded Fasteners,
1.6 For metric bolts, see SpecificationA 490M Classes 10.9
Washers, and Rivets
and 10.9.3
F 788/F 788M Specification for Surface Discontinuities of
1.7 The following safety hazards caveat pertains only to the
Bolts, Screws, and Studs, Inch and Metric Series
Test Methods portion, Section 12 of this specification: This
F 959 Specification for Compressible-Washer-Type Direct
standard does not purport to address all of the safety concerns,
Tension Indicators for Use with Structural Fasteners
if any, associated with its use. It is the responsibility of the user
F 1470 GuideforFastenerSamplingforSpecifiedMechani-
of this standard to establish appropriate safety and health
cal Properties and Performance Inspection
practices and determine the applicability of regulatory limita-
F 1789 Terminology for F16 Mechanical Fasteners
tions prior to use.
G 101 Guide for Estimating the Atmospheric Corrosion
Resistance of Low-Alloy Steels
1
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts,
Nuts, Rivets, and Washers.
3
Current edition approved Aug. 1, 2004. Published August 2004. Originally For referenced ASTM standards, visit the ASTM website, www.astm.org, or
approved in 1964. Last previous edition approved in 2004 as A 490 – 04. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
Available from American Institute of Steel Construction (AISC), One E. Standards volume information, refer to the standard’s Document Summary page on
Wacker Dr., Suite 3100, Chicago, IL 60601-2001. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 490 – 04a
4
2.2 ASME Standards: 4. Materials and Manufacture
B1.1 Unified Screw Threads
4.1 Heat Treatment—Type 1 and Type 3 bolts shall be heat
B18.2.6 Fasteners for Use in Structural Applications
treated by quenching in oil from the austenitic temperature and
B18.24.1 Part Identifying Number (PIN) Code System
then
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.