ASTM D2564-12(2018)
(Specification)Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
SCOPE
1.1 This specification covers requirements for poly(vinyl chloride) (PVC) solvent cements to be used in joining poly(vinyl chloride) piping systems.
1.2 These solvent cements are used with poly(vinyl chloride) piping systems made from compounds as defined in Specification D1784.
1.3 A procedure for joining PVC pipe and fittings is given in Practice D2855.
1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2564 −12 (Reapproved 2018) An American National Standard
Standard Specification for
Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic
1
Piping Systems
This standard is issued under the fixed designation D2564; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers requirements for poly(vinyl 2.1 ASTM Standards:
chloride) (PVC) solvent cements to be used in joining poly- D1084Test Methods for Viscosity of Adhesives
(vinyl chloride) piping systems. D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
tics
1.2 These solvent cements are used with poly(vinyl chlo-
D1784Specification for Rigid Poly(Vinyl Chloride) (PVC)
ride) piping systems made from compounds as defined in
Compounds and Chlorinated Poly(Vinyl Chloride)
Specification D1784.
(CPVC) Compounds
1.3 AprocedureforjoiningPVCpipeandfittingsisgivenin
D1785Specification for Poly(Vinyl Chloride) (PVC) Plastic
Practice D2855.
Pipe, Schedules 40, 80, and 120
D2467Specification for Poly(Vinyl Chloride) (PVC) Plastic
1.4 Thetextofthisspecificationreferencesnotes,footnotes,
Pipe Fittings, Schedule 80
and appendixes which provide explanatory material. These
D2855Practice for the Two-Step (Primer and Solvent Ce-
notesandfootnotes(excludingthoseintablesandfigures)shall
ment) Method of Joining Poly (Vinyl Chloride) (PVC) or
not be considered as requirements of the specification.
Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and
1.5 The values stated in inch-pound units are to be regarded
Piping Components with Tapered Sockets
as standard. The values given in parentheses are mathematical
F402 Practice for Safe Handling of Solvent Cements,
conversions to SI units that are provided for information only
Primers, and Cleaners Used for Joining Thermoplastic
and are not considered standard.
Pipe and Fittings
1.6 The following safety hazards caveat pertains only to the
F412Terminology Relating to Plastic Piping Systems
test methods portion, Section 6, of this specification: This
F493Specification for Solvent Cements for Chlorinated
standard does not purport to address all of the safety concerns,
Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
if any, associated with its use. It is the responsibility of the user 3
2.2 National Sanitation Foundation Standards:
of this standard to establish appropriate safety, health, and
Standard No. 14for Plastic Piping Components and Related
environmental practices and determine the applicability of
Materials
regulatory limitations prior to use.
StandardNo.61forDrinkingWaterSystemsComponents—
1.7 This international standard was developed in accor-
Health Effects
dance with internationally recognized principles on standard-
3. Terminology
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
3.1 Definitions—Definitions are in accordance with Termi-
mendations issued by the World Trade Organization Technical
nology F412, and abbreviations are in accordance with Termi-
Barriers to Trade (TBT) Committee.
nology D1600, unless otherwise specified.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Aug. 1, 2018. Published August 2018. Originally the ASTM website.
3
approved in 1966. Last previous edition approved in 2012 as D2564–12. DOI: Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd.,Ann
10.1520/D2564-12R18. Arbor, MI 48113-0140, http://www.nsf.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2564−12 (2018)
4. Materials and Manufacture 6. Test Methods
4.1 The solvent cement shall be a solution of the base PVC 6.1 Solids Content:
6.1.1 Apparatus:
resin used to make Class 12454-B poly(vinyl chloride) mold-
ing or extrusion compound as defined in Specification D1784. 6.1.1.1 Ointment Tins (Style No. 12, 1-oz (30-mL), all
metal).
4.2 When rework material is used, the manufacturer shall
6.1.1.2 Vacuum. Oven
use only his own clean rework material that is compatible
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2564 − 12 D2564 − 12 (Reapproved 2018) An American National Standard
Standard Specification for
Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic
1
Piping Systems
This standard is issued under the fixed designation D2564; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers requirements for poly(vinyl chloride) (PVC) solvent cements to be used in joining poly(vinyl
chloride) piping systems.
1.2 These solvent cements are used with poly(vinyl chloride) piping systems made from compounds as defined in Specification
D1784.
1.3 A procedure for joining PVC pipe and fittings is given in Practice D2855.
1.4 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes
and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D1084 Test Methods for Viscosity of Adhesives
D1600 Terminology for Abbreviated Terms Relating to Plastics
D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)
Compounds
D1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
D2467 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
D2855 Practice for the Two-Step (Primer and Solvent Cement) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated
Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets
F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings
F412 Terminology Relating to Plastic Piping Systems
F493 Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
3
2.2 National Sanitation Foundation Standards:
Standard No. 14 for Plastic Piping Components and Related Materials
Standard No. 61 for Drinking Water Systems Components—Health Effects
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.
Current edition approved Aug. 1, 2012Aug. 1, 2018. Published December 2012August 2018. Originally approved in 1966. Last previous edition approved in 20092012
ε1
as D2564 – 04(2009)D2564 –12. . DOI: 10.1520/D2564-12.10.1520/D2564-12R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http://www.nsf.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2564 − 12 (2018)
3. Terminology
3.1 Definitions—Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology
D1600, unless otherwise specified.
4. Materials and Manufacture
4.1 The solvent ceme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.