prEN ISO 18889
(Main)Protective gloves for pesticide operators - Performance requirements (ISO/DIS 18889:2017)
Protective gloves for pesticide operators - Performance requirements (ISO/DIS 18889:2017)
This International Standard establishes minimum performance, classification, and labelling requirements for
gloves worn by operators handling pesticide products. Gloves covered by this International Standard include
waterproof and chemical resistant gloves made with elastomeric and other air impermeable materials. This
standard does not address protection against fumigants or highly volatile liquids.
Schutzhandschuhe für Anwender von Pflanzenschutzmitteln — Leistungsanforderungen (ISO/DIS 18889:2017)
Gant de protection pour les opérateurs manipulants des pesticides -exigences de performance (ISO/DIS 18889:2017)
Varovalne rokavice za uporabnike pesticidov - Zahtevane lastnosti (ISO/DIS 18889:2017) TC: Varovalne rokavice za uporabnike, ki rokujejo s pesticidi - Zahtevane lastnosti (ISO/DIS 18889:2017)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2017
Varovalne rokavice za uporabnike pesticidov - Zahtevane lastnosti (ISO/DIS
18889:2017)
Protective gloves for pesticide operators - Performance requirements (ISO/DIS
18889:2017)
Schutzhandschuhe für Anwender von Pflanzenschutzmitteln — Leistungsanforderungen
(ISO/DIS 18889:2017)
Gant de protection pour les opérateurs manipulants des pesticides -exigences de
performance (ISO/DIS 18889:2017)
Ta slovenski standard je istoveten z: prEN ISO 18889
ICS:
13.340.40 Varovanje dlani in rok Hand and arm protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18889
ISO/TC 94/SC 13 Secretariat: SNV
Voting begins on: Voting terminates on:
2017-07-27 2017-10-18
Protective gloves for pesticide operators — Performance
requirements
Gant de protection pour les opérateurs manipulants des pesticides — exigences de performance
ICS: 13.340.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 18889:2017(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2017
ISO/DIS 18889:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO/DIS 18889:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Sampling . 3
4.1 Sampling for permeation . 3
4.2 Sampling for penetration . 3
5 Performance requirements of glove materials . 3
5.1 General requirements . 3
5.2 Penetration . 3
5.3 Permeation . 4
5.4 Glove design requirement . 4
5.5 Mechanical requirements . 5
5.6 Requirements for protective glove for pesticides operator . 5
6 Marking . 5
6.1 General . 5
6.2 Specific . 5
7 Information supplied by the manufacturer . 6
Annex A (informative) Risk Assessment — PPE to mitigate risk . 8
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/425 aimed to be covered .9
Annex ZB (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 89/686/ECC .10
Bibliography .11
ISO/DIS 18889:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www . i so .org/ iso/ foreword .html.
ISO 18889 was prepared by Technical Committee ISO/TC 94, Personal safety - Protective clothing
and equipment, Subcommittee SC 13, Protective clothing and by Technical Committee CEN/TC 162,
Protective clothing including hand and arm protection and lifejackets in collaboration.
iv © ISO 2017 – All rights reserved
ISO/DIS 18889:2017(E)
Introduction
This document addresses the performance requirements for gloves worn by operators when mixing
and loading, applying pesticide, as well as handling pesticide for other tasks. Pesticide products are
known as plant protection products (PPP) in certain countries/regions of the world.
Since active ingredient of pesticide is typically a chemical with low vapour pressure and/or low solubility
in collection media, EN 16523-1:2015 cannot be used to measure permeation of active ingredient in
most pesticide products. Therefore, ISO/DIS 19918 is used to measure cumulative permeation of active
ingredient in pesticide products. Requirements other than the ISO/DIS 19918 test are similar to those
for other chemical resistant gloves.
This document defines performance requirements for two levels of gloves with specified resistance to
permeation by pesticide products. A brief description of the levels is given below:
Level G1 glove is suitable when the potential risk is relatively low. Level G1 gloves are not suitable for
use with concentrated pesticide formulations.
Level G2 gloves are suitable when the potential risk is higher. Level G2 gloves are suitable for use with
diluted as well as concentrated pesticides.
Personal Protective Equipment (PPE) is often used for risk mitigation. See Annex A for information
on risk assessment and use of PPE for risk mitigation. Since protective gloves can be contaminated
in various ways (e.g., fine spray, contact with wet surface, contact with pesticide product sprayed
under pressure, contact between the protective gloves and a contaminated surface), in this standard
laboratory tests methods are used to rate materials rather than simulate field conditions.
Registration of pesticide products, such as insecticides, herbicides, and fungicides, involves the
assessment of operator exposure and risk, which determines the need for personal protective
equipment. Protection should correspond to the identified risks in order to avoid loss of comfort due
to overprotection. Actual field trials are used to determine the operator risk while spraying pesticides
under different scenarios. Laboratory data often are derived from accelerated tests to differentiate
among different levels of performance; therefore, laboratory data cannot be used for direct comparison
with field data for determining acceptable mitigation factors.
This document is intended for glove manufacturers, pesticide product manufacturers, trainers,
regulators, and other individuals or organizations that make decisions regarding PPE for protection
against pesticide products.
DRAFT INTERNATIONAL STANDARD ISO/DIS 18889:2017(E)
Protective gloves for pesticide operators — Performance
requirements
1 Scope
This document establishes minimum performance, classification, and labelling requirements for gloves
worn by operators handling pesticide products. Gloves covered by this International Standard include
gloves made with elastomeric and other air impermeable materials. This standard does not address
protection against fumigants.
This document should be used in conjunction with EN 420.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 374-1:2016, Protective gloves against dangerous chemicals and micro-organisms — Part 1: Terminology
and performance requirements for chemical risks
ISO 3696:1995, Water for analytical laboratory use. Specification and test methods
ISO/DIS 19918:2016, Protective clothing — Protection against liquid chemicals — Measurement of
cumulative permeation of chemicals with low vapour pressure through protective clothing, footwear and
glove materials
EN 374-2:2014, Protective gloves against chemicals and micro-organisms — Part 2: Determination of
resistance to penetration
EN 388:2016, Protective gloves for pesticide operators — Performance requirements against mechanical risks
EN 420:2003, Protective gloves — General requirements and test methods
Note EN 420 shall be replaced by ISO 21420 once published
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http:// www .electropedia .org/
— ISO Online browsing platform: available at http:// www .iso .org/ obp
3.1
active ingredient
component of a pesticide formulation, which is an active substance present in sufficient quantity that
relates to an intended
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.