iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14982:2006/FprA1

(Amendment)

Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness

Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness

This European Standard specifies a test method for assessing the tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.
NOTE    This is intended as a test of the structural integrity of riser shafts supporting product standards prEN 13598 2 [1] and prEN 15229 [2].

Kunststoff-Rohrleitungssysteme und Schutzrohrsysteme - Schachtringe und Steigrohre für Kontroll- und Einsteigschächte aus thermoplastischen Kunststoffen - Bestimmung der Ringsteifigkeit

Systèmes de canalisations et de gaines en plastique - Eléments de rehausse en matière thermoplastique pour chambres d'inspection ou regards - Détermination de la rigidité annulaire

Cevni sistemi iz polimernih materialov - Plastomerni revizijski in vstopni jaški - Določanje obodne togosti

General Information

Status
Not Published
ICS
93.030 - External sewage systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 20 - Thermoplastics ancillaries for soil and waste discharge and gravity buried drainage and sewerage systems
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
01-Jul-2010
Due Date
27-Nov-2010
Completion Date
01-Jul-2010
Ref Project
SIST EN 14982:2007/kFprA1:2010 - Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness

Relations

Merged Into
EN 14982:2006+A1:2010 - Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness
Effective Date
19-Jan-2023
Amends
EN 14982:2006 - Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness
Effective Date
22-Dec-2008

Buy Standard

EN 14982:2007/kFprA1:2010EN 14982:2007/kFprA1:2010
PreviousNext
Draft
EN 14982:2007/kFprA1:2010
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14982:2007/kFprA1:2010
01-junij-2010
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY3ODVWRPHUQLUHYL]LMVNLLQYVWRSQLMDãNL
'RORþDQMHRERGQHWRJRVWL
Plastics piping and ducting systems - Thermoplastics shafts or risers for inspection
chambers and manholes - Determination of ring stiffness
Kunststoff-Rohrleitungssysteme und Schutzrohrsysteme - Schachtringe und Steigrohre
für Kontroll- und Einsteigschächte aus thermoplastischen Kunststoffen - Bestimmung der
Ringsteifigkeit
Systèmes de canalisations et de gaines en plastique - Eléments de rehausse en matière
thermoplastique pour chambres d'inspection ou regards - Détermination de la rigidité
annulaire
Ta slovenski standard je istoveten z: EN 14982:2006/FprA1
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 14982:2007/kFprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 14982:2007/kFprA1:2010

---------------------- Page: 2 ----------------------

SIST EN 14982:2007/kFprA1:2010


EUROPEAN STANDARD
FINAL DRAFT
EN 14982:2006
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
April 2010
ICS 93.030
English Version
Plastics piping and ducting systems - Thermoplastics shafts or
risers for inspection chambers and manholes - Determination of
ring stiffness
Systèmes de canalisations et de gaines en plastique - Kunststoff-Rohrleitungssysteme und Schutzrohrsysteme -
Eléments de rehausse en matière thermoplastique pour Schachtringe und Steigrohre für Kontroll- und
chambres d'inspection ou regards - Détermination de la Einsteigschächte aus thermoplastischen Kunststoffen -
rigidité annulaire Bestimmung der Ringsteifigkeit
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 155.

This draft amendment A1, if approved, will modify the European Standard EN 14982:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE F
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17670-2:2023(Main)
Plastics piping systems for non-pressure underground conveyance of surface water - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specification for road gullies
SIST EN 17670-2:2024

This document specifies the definitions and requirements for unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) road gullies intended for use in non-pressure underground drains and sewers for surface water having a maximum depth of 4 m from ground level to the lowest point of the internal surface of the road gully. Road gullies complying with this document are intended to be used in pedestrian or vehicular traffic areas outside the building structure.
NOTE 1   Products complying with this document can also be used in non-traffic areas.
NOTE 2   Road gullies can be subject to national regulation which limit the maximum installation depth and / or local provisions. The installer checks for compliance prior to installation.
Road gullies complying with this document are made from a prescribed set of components that are manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), polypropylene with mineral modifier (PP-MD) or polyethylene (PE) and assembled together.
Road gullies complying with this document may be equipped with optional devices (e.g. removable sand or silt bucket, leaf separator etc.), however the performance of these optional devices is not covered within the scope of this document.
Road gully components can be manufactured by various methods e.g. extrusion, injection moulding, rotational moulding, low-pressure moulding, blow moulding, thermoforming or fabricated.
NOTE 3   Products complying with this document can be installed in underground applications without additional static calculation.
NOTE 4   The complete road gully assembly can also include non-plastic items (near surface or surface components for example) which are not covered by this document.
NOTE 5   The complete road gully assembly can be supplied with covers, frame covers and gratings complying with the relevant part of EN 124 which are not covered by this document. However, reference is made to this document for geometrical characteristics where applicable.
NOTE 6   Road gullies can be site assembled from different components, but can also be manufactured as a single unit.
This document covers:
-   road gullies with or without sand / silt trap;
-   road gullies with or without water seal preventing odour release;
-   road gullies where the traffic load will or will not be carried by the complete gully (resp. "Direct loaded gullies" or "Indirect loaded gullies").

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 14632:2023(Main)
Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
SIST-TS CEN/TS 14632:2023

This document gives guidance on the assessment of conformity of GRP-UP (glass-reinforced thermosetting resins based on unsaturated polyesters) piping products and assemblies in accordance with EN ISO 23856. ISO 25780 and ISO 16611 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
This document also gives guidance on the assessment of conformity of GRP-UP manholes and inspection chambers (see EN 15383 for additional information). Pipes (see EN ISO 23856) are used for manufacturing the shafts and chamber units. Additional statements as needed to assess the conformity of manholes and inspection chambers are given in Annex F.
NOTE 1   For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).
NOTE 2   If third-party certification is involved, the certification body is accredited to ISO/IEC 17065 or EN ISO/IEC 17021 [3] as applicable.

  • Technical specification
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14758-1:2023(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system
SIST EN 14758-1:2023

This document specifies the requirements for solid-wall pipes and fittings with or without internal and/or external skin, and the system of piping systems made from mineral modified polypropylene materials (PP-MD) in the field of non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and non-pressure underground drainage and sewerage for both buried in ground within the building structure and outside the building structure (application area code "UD").
This is reflected in the marking of products by "U" and "UD".
NOTE 1   The skins are made of PP compound without mineral modifier.
It also specifies the test parameters for the test methods referred to in this document.
This document covers a range of nominal sizes, a range of pipe stiffness classes and gives recommendations concerning colours.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
In conjunction with Part 2 of EN 14758 (see European foreword) it is applicable to PP-MD pipes and fittings, their elastomeric sealing ring joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
This document is applicable to PP-MD pipes with or without an integral socket and fittings with an integral socket.
NOTE 3   The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, when they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 11.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13267:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
SIST EN ISO 13267:2023

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
SIST EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
SIST EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 13598-3:2021(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity
SIST-TS CEN/TS 13598-3:2022

This document gives guidance for requirements for the assessment of conformity of materials (compounds/formulations), products, joints and assemblies in accordance with the applicable part(s) of EN 13598-1 and EN 13598-2 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   The quality management system is expected to conform to or be no less stringent than the relevant requirements of EN ISO 9001 [1].
NOTE 2   If certification is involved, the certification body is expected to be compliant with EN ISO/IEC 17065 [5].
NOTE 3   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 13598-1 and EN 13598-2 (see Foreword) this document is applicable to ancillary fittings including shallow chambers and manholes and inspection chambers.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 23856:2021(Main)
Plastics piping systems for pressure and non-pressure water supply, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin (ISO 23856:2021)
SIST EN ISO 23856:2021

This document specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). It is suited for all types of water supply, drainage and sewerage with or without pressure. Types of water supply include, but are not limited to, raw water, irrigation, cooling water, potable water, salt water, sea water, penstocks in power plants, processing plants and other water-based applications. This document is applicable to GRP UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in direct buried installations.
NOTE 1   For the purpose of this document, the term polyester resin (UP) also includes vinyl-ester resins (VE).
NOTE 2   Piping systems conforming to this document can also be used for non-buried applications, provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints.
NOTE 3   This document can also apply for other installations, such as slip-lining rehabilitation of existing pipes.
NOTE 4   ISO 10467 and ISO 10639, which are replaced by this document, are also referenced in ISO 25780, which specifies requirements for GRP-pipes used for jacking installation.
The requirements for the hydrostatic pressure design of pipes referring to this document meet the requirements of ISO/TS 20656-1 and the general principle for the reliability of structures detailed in ISO 2394 and in EN 1990. These International Standards provide procedures for the harmonization of design practices and address the probability of failure, as well as possible consequences of failures. The design practices are based on a partial safety factor concept, as well as on risk management engineering.
This document is applicable to circular pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000, which are intended to be used for the conveyance of water, sewage and drainage at normal service conditions, with or without pressure.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-4:2018/A1:2021(Amendment)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
SIST EN ISO 11296-4:2018/A1:2021

2021-02-11 - TC decision is missing to skip FV.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1046:2021(Main)
Thermoplastics piping and ducting systems - Outside the building structures for gravity and pressurised systems - Trench installation
SIST-TS CEN/TS 1046:2021

This document gives the recommended practise for underground open trench installation and commissioning of thermoplastics piping systems to be used for the conveyance of water under pressure (in addition to EN 805) and for the discharge of wastewater under gravity (in addition to EN 1610) .
In the field of non-pressure underground drainage and sewerage this is reflected in the marking of products by application code "U" and "UD":
-   outside the building structure (U);
-   both buried in ground within the building structure (application area code "D") and outside the
building (application area code "UD").
This document covers also installation and/or connections to valves, manholes, inspection chambers, gullies and other ancillary components in piping systems.
NOTE 1   Code of practise for pipelines for gas supply is covered by EN 12007-series [21].
NOTE 2   Recommended practices for installation of plastic piping systems for soil and waste discharge within the building structure is covered by CEN/TR 13801 [12].
NOTE 3   Practices for underground installation of rainwater infiltration and storage attenuation systems are covered by CEN/TR 17179 [13].
NOTE 4   It is assumed that additional recommendations and/or requirements are detailed in the individual product standards.
NOTE 5    If non-plastic components are part of the plastic system the manufacturer's instructions should be taken into account.
Requirements and instructions concerning commissioning of systems can be found in EN 805 and EN 1610 and the relevant national and/or local regulations. This document gives specific additional recommendations for commissioning relevant for plastic piping systems.
Attention is drawn to any relevant local and/or national regulations (e.g. health, safety and hygienic requirements).

  • Technical specification
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day