CEN/TS 17670-3:2024
(Main)Plastics piping systems for non-pressure underground conveyance of surface water - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity
Plastics piping systems for non-pressure underground conveyance of surface water - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Assessment of conformity
This document gives guidance and requirements for the assessment of conformity of materials (compounds/formulations), products, joints and assemblies in accordance with EN 17670 2 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1 A test matrix provides an overview of the testing scheme in Annex A, Table A.1.
NOTE 2 If certification is involved, the certification body operating in accordance with EN ISO/IEC 17065 [1] and EN ISO/IEC 17020 [2] is considered to be competent.
In conjunction with EN 17670 2 this document is applicable to road gullies.
Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Ableitung von Oberflächenwasser - Weichmacherfreies Poly(vinylchlorid) (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 3: Beurteilung der Konformität
Dieses Dokument enthält die Anforderungen und gibt Empfehlungen für die Beurteilung der Konformität von Werkstoffen (Formmassen/Zusammensetzungen), Erzeugnissen, Verbindungen und Bauteilkombinationen, die in Übereinstimmung mit EN 17670 2 für eine Einbeziehung in den Qualitätssicherungsplan des Herstellers als Teil des Qualitätsmanagementsystems und für die Erstellung von Zertifizierungsverfahren vorgesehen sind.
ANMERKUNG 1 Anhang A, Tabelle A.1 enthält einen Überblick über das Prüfschema in Form einer Prüfmatrix.
ANMERKUNG 2 Wenn eine Zertifizierung einbezogen ist, wird die in Übereinstimmung mit EN ISO/IEC 17065 [1] bzw. EN ISO/IEC 17020 [2] arbeitende Zertifizierungsstelle als kompetent angesehen.
In Verbindung mit EN 17670 2 ist dieses Dokument anwendbar für Straßenabläufe.
Systèmes de canalisations en plastique pour le transport souterrain sans pression des eaux de surface - Poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et polyéthylène (PE) - Partie 3 : Évaluation de la conformité
Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport površinske vode - Neplastificiran polivinilklorid (PVC-U), polipropilen (PP) in polietilen (PE ) - 3. del: Ugotavljanje skladnosti
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2025
Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so
položeni v zemljo, za transport površinske vode - Neplastificiran polivinilklorid
(PVC-U), polipropilen (PP) in polietilen (PE ) - 3. del: Ugotavljanje skladnosti
Plastics piping systems for non-pressure underground conveyance of surface water -
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -
Part 3: Assessment of conformity
Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Ableitung von
Oberflächenwasser - Weichmacherfreies Poly(vinylchlorid) (PVC-U), Polypropylen (PP)
und Polyethylen (PE) - Teil 3: Beurteilung der Konformität
Systèmes de canalisations en plastique pour le transport souterrain sans pression des
eaux de surface - Poly(chlorure de vinyle) non plastifié (PVC-U), polypropylène (PP) et
polyéthylène (PE) - Partie 3 : Évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 17670-3:2024
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 17670-3
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
December 2024
TECHNISCHE SPEZIFIKATION
ICS 93.030
English Version
Plastics piping systems for non-pressure underground
conveyance of surface water - Unplasticized poly(vinyl
chloride) (PVC-U), polypropylene (PP) and polyethylene
(PE) - Part 3: Assessment of conformity
Kunststoff-Rohrleitungssysteme für die drucklose
unterirdische Ableitung von Oberflächenwasser -
Weichmacherfreies Poly(vinylchlorid) (PVC-U),
Polypropylen (PP) und Polyethylen (PE) - Teil 3:
Beurteilung der Konformität
This Technical Specification (CEN/TS) was approved by CEN on 11 November 2024 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 17670-3:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Abbreviated terms . 8
5 General. 8
6 Testing . 8
6.1 Grouping. 8
6.1.1 General. 8
6.1.2 Size groups . 8
6.1.3 Gully type groups . 9
6.2 Type testing . 9
6.2.1 General. 9
6.2.2 Change of material – PVC-U formulation . 13
6.2.3 Change of material – Polypropylene compound . 14
6.2.4 Change of material – Polyethylene compound . 15
6.3 Batch release testing . 16
6.4 Process verification testing . 18
6.5 Audit testing . 19
6.6 Test records . 21
Annex A (informative) Test matrix . 22
Bibliography . 24
European foreword
This document (CEN/TS 17670-3:2024) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
EN 17670 consists of the following parts, under the general title “Plastics piping systems for non-pressure
underground conveyance of surface water — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP)
and polyethylene (PE)”:
— Part 1: Specifications for manholes and inspection chambers (under development);
— Part 2: Specification for road gullies;
— Part 3: Assessment of conformity (this document).
This version of Part 3 covers products according to Part 2. Part 1 is still under development and will be
included if/when available.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Introduction
This document details the applicable characteristics to be assessed for type testing (TT), batch release
test (BRT), process verification test (PVT), and audit test (AT), as well as the frequency and sampling for
testing.
The concept of testing and organization of those tests used for the AoC is shown, without or with
certification, in Figures 1 and 2.
Figure 1 — Typical scheme for the AoC by a manufacturer, without certification
Figure 2 — Typical scheme for the AoC by a manufacturer, including certification
1 Scope
This document gives guidance and requirements for the assessment of conformity of materials
(compounds/formulations), products, joints and assemblies in accordance with EN 17670-2 intended to
be included in the manufacturer’s quality plan as part of the quality management system and for the
establishment of certification procedures.
NOTE 1 A test matrix provides an overview of the testing scheme in Annex A, Table A.1.
NOTE 2 If certification is involved, the certification body operating in accordance with EN ISO/IEC 17065 [1] and
EN ISO/IEC 17020 [2] is considered to be competent.
In conjunction with EN 17670-2 this document is applicable to road gullies.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 17670-2, Plastics piping systems for non-pressure underground conveyance of surface water —
Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2:
Specification for road gullies
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 17670-2 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
3.1
certification body
third-party conformity assessment body operating certification schemes
Note 1 to entry: A certification body can be non-governmental or governmental (with or without regulatory
authority).
[SOURCE: EN ISO/IEC 17065:2012 [1], definition 3.12]
3.2
laboratory
body that performs one or more of the following activities:
— testing;
— calibration;
— sampling, associated with subsequent testing or calibration
Note 1 to entry: In the context of this document, the materials and products can be subjected to type testing, batch
release testing, process verification testing and audit testing, as applicable.
[SOURCE: EN ISO/IEC 17025:2017 [3], definition 3.6, modified — Note 1 to entry is changed here]
3.3
quality management system
part of a management system with regard to quality
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [4].
[SOURCE: EN ISO 9000:2015 [5], definition 3.5.4, modified — Note 1 to entry is added here]
3.4
quality plan
document setting out the specific quality practices, responsibilities, resources and sequence of activities
relevant to a particular product or range of products
3.5
type test
TT
test performed to prove that the material, component, product, joint or assembly is capable of conforming
to the requirement(s) given in the relevant standard or if applicable to determine the manufacturer’s
declared values
3.6
batch release test
BRT
test performed on a batch of material, components, products, joints or assemblies which has to be
satisfactorily completed before the batch can be released
Note 1 to entry: A batch release test can be performed by the manufacturer or outsourced on behalf of the
manufacturer.
3.7
process verification test
PVT
test performed on material, component, product, joint or assembly by or on behalf of the manufacturer
on compound or products or joints or assemblies at specific intervals to confirm that type tests originally
performed continue to be valid
Note 1 to entry: Process verification tests can be performed by the manufacturer or outsourced on behalf of the
manufacturer.
3.8
audit test
AT
test performed on behalf of a certification body
Note 1 to entry: Audit tests are generally required to confirm that the material (formulation/compound), product,
joint or assembly continues to conform to the requirements given in the relevant standard and to provide
information to assess the effectiveness of the quality management system.
3.9
indirect test
batch release test performed which differs from that specified test for that particular characteristic,
having previously verified its correlation with the specified test
Note 1 to entry: Indirect tests can be performed by the manufacturer or outsourced on behalf of the manufacturer.
3.10
witness test
type test or audit test which is performed in the presence of a representative of the certification body
3.11
material
generic term for compounds/formulations grouped by families, expressed by generic names
Note 1 to entry: Examples of generic names are PVC-U, polypropylene and EPDM.
3.12
substance
polymer, additive, element or chemical compound as used in compounds/formulations
3.13
compound/formulation
homogenous mixture of substances used for the manufacture of the product as defined in the referring
product standard
Note 1 to entry: In gene
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.