EN 4642:2009
(Main)Aerospace series - Steel FE-PM 3504 (X4CrNiMo16-5-1) - Air melted - Hardened and tempered - Sheet and plate - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Aerospace series - Steel FE-PM 3504 (X4CrNiMo16-5-1) - Air melted - Hardened and tempered - Sheet and plate - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
This standard specifies the requirements relating to:
Steel FE-PM 3504 (X4CrNiMo16-5-1)
Air melted
Hardened and tempered
Sheet and plate
0,6 mm < or = a < or = 50 mm
900 MPa < or = Rm < or = 1 050 MPa
for aerospace applications.
Luft- und Raumfahrt - Stahl FE-PM 3504 (X4CrNiMo16-5-1) - Lufterschmolzen - Gehärtet- und angelassen - Bleche und Platten - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Série aérospatiale - Acier FE-PM 3504 (X4CrNiMo16-5-1) - Élaboré à l'air - Trempé et revenu - Tôles et plaques - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Aeronavtika - Jeklo FE-PM 3504 (X4CrNiMo16-5-1) - Taljeno - Utrjeno in mehko žarjeno - Pločevina in plošče - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1050 MPa
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.03D49.025.10JeklaSteelsICS:Ta slovenski standard je istoveten z:EN 4642:2009SIST EN 4642:2009en01-maj-2009SIST EN 4642:2009SLOVENSKI
STANDARD
SIST EN 4642:2009
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4642
February 2009 ICS 49.025.10 English Version
Aerospace series - Steel FE-PM 3504 (X4CrNiMo16-5-1) - Air melted - Hardened and tempered - Sheet and plate - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Série aérospatiale - Acier FE-PM 3504 (X4CrNiMo16-5-1) -Élaboré à l'air - Trempé et revenu - Tôles et plaques - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa
Luft- und Raumfahrt - Stahl FE-PM 3504 (X4CrNiMo16-5-1) - Lufterschmolzen - Gehärtet- und angelassen - Bleche und Platten - 0,6 mm ≤ a ≤ 50 mm - 900 MPa ≤ Rm ≤ 1 050 MPa This European Standard was approved by CEN on 11 July 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4642:2009: ESIST EN 4642:2009
EN 4642:2009 (E) 2 Foreword This document (EN 4642:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2009, and conflicting national standards shall be withdrawn at the latest by August 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 4642:2009
EN 4642:2009 (E) 3 Introduction This standard is part of the series of EN metallic material standards for aerospace applications. The general organization of this series is described in EN 4258. This standard has been prepared in accordance with EN 4500-5. 1 Scope This standard specifies the requirements relating to: Steel FE-PM 3504 (X4CrNiMo16-5-1) Air melted Hardened and tempered Sheet and plate 0,6 mm ≤ a ≤ 50 mm 900 MPa ≤ Rm ≤ 1 050 MPa for aerospace applications. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2043, Aerospace series — Metallic materials — General requirements for semi-finished product qualification (excluding forgings and castings) 1 EN 2951, Aerospace series — Metallic materials — Test method — Micrographic determination of content of non-metallic inclusions 1 EN 4050-4, Aerospace series — Test method for metallic materials — Ultrasonic inspection of bars, plates, forging stock and forgings — Part 4: Acceptance criteria 1 EN 4258, Aerospace series — Metallic materials — General organization of standardization — Links between types of EN standards and their use EN 4500-5, Aerospace series — Metallic materials — Rules for drafting and presentation
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.