EN 15814:2011/FprA2
(Amendment)Polymer modified bituminous thick coatings for waterproofing - Definitions and requirements
Polymer modified bituminous thick coatings for waterproofing - Definitions and requirements
This European Standard specifies the definitions and requirements of prefabricated polymer modified bituminous thick coatings used for the waterproofing of below ground structures. It applies to both one-component and two-component products. These products can be used with or without inlay. This European Standard does not apply to products that are to be used for roof waterproofing.
Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Begriffe und Anforderungen
Revêtements bitumineux épais modifiés aux polymères pour imperméabilisation - Définitions et exigences
Bitumenske debeloslojne prevleke, modificirane s polimeri - Definicije in zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2014
Bitumenske debeloslojne prevleke, modificirane s polimeri - Definicije in zahteve
Polymer modified bituminous thick coatings for waterproofing - Definitions and
requirements
Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Begriffe
und Anforderungen
Revêtements bitumineux épais modifiés aux polymères pour imperméabilisation -
Définitions et exigences
Ta slovenski standard je istoveten z: EN 15814:2011/FprA2
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN 15814:2011+A1:2012
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
June 2014
ICS 91.100.50
English Version
Polymer modified bituminous thick coatings for waterproofing -
Definitions and requirements
Revêtements bitumineux épais modifiés aux polymères Kunststoffmodifizierte Bitumendickbeschichtungen zur
pour imperméabilisation - Définitions et exigences Bauwerksabdichtung - Begriffe und Anforderungen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 361.
This draft amendment A2, if approved, will modify the European Standard EN 15814:2011+A1:2012. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15814:2011/FprA2:2014 E
worldwide for CEN national Members.
Contents Page
Foreword .3
1 Modification to Clause 2 .4
2 Modification to Clause 4 .4
3 Modification to Clause 4, Table 1, line 3, column 2 .4
4 Modification to Clause 5 .4
5 Assessment and verification of the constancy of performance – AVCP .4
5.1 General .4
5.2 Type testing .4
5.2.1 General .4
5.2.2 Test reports .5
5.3 Factory production control (FPC) .5
5.3.1 General .5
5.3.2 Requirements .6
5.3.3 Product specific requirements .9
5.3.4 Initial inspection of factory and of FPC .9
5.3.5 Continuous surveillance of FPC . 10
5.3.6 Procedure for modifications . 10
6 Modification to Annex ZA . 10
Annex ZA (informative) Clauses of this European Standard addressing provisions of the
EU Construction Products Regulation (CPR) . 11
ZA.1 Scope and relevant characteristics . 11
ZA.2 Procedures for AVCP of the PMBC . 12
ZA.2.1 Systems of AVCP . 12
ZA.2.2 Declaration of performance (DoP) . 15
ZA.3 CE marking and labelling . 19
7 Addition of a Bibliography . 20
Foreword
This document (EN 15814:2011/FprA2:2014) has been prepared by Technical Committee CEN/TC 361
"Project Committee - Polymer modified bituminous thick coatings for waterproofing - Definitions/requirements
and test methods", the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
Note: Due to fact that the Framework Partnership Agreement between the Commission and CEN & CENELEC
is not signed yet, there are currently no New Approach Consultants in place for 2014. Therefore the provisions
of CEN-CENELEC Guide 15 cannot be met.
This shall not prevent the processing of draft standards nor the offering of harmonized standards to the
Commission. In particular, draft standards can be sent to vote without Consultant assessment.
This note will be removed from the Foreword of the finalized publication.
1 Modification to Clause 2
Replace "ISO 1183-1:2004" with "EN ISO 1183-1".
Delete the reference to "EN ISO 2811-2".
2 Modification to Clause 4
Under Clause 4 "Requirements" add a new headline for sub-clause "4.1 General".
Add a new sub-clause "4.2 Dangerous substances" with the following text:
"National regulations on dangerous substances may require verification and declaration on release, and
sometimes content, when construction products covered by this standard are placed on those markets. In the
absence of European harmonised test methods, verification and declaration on release/content should be
done taking into account national provisions in the place of use.
NOTE An informative database covering European and national provisions on dangerous substances is available at the
Construction web site on EUROPA accessed through: http://ec.europa.eu/enterprise/construction/cpd-ds/."
3 Modification to Clause 4, Table 1, line 3, column 2
Replace "No changes to the material according to EN 15817," by a third requirement "3. No changes to the
material".
4 Modification to Clause 5
Replace the entire Clause 5 with the following.
"
5 Assessment and verification of the constancy of performance – AVCP
5.1 General
The compliance of PMBC with the requirements of this standard and with the declared values (including
classes) shall be demonstrated by:
determination of the product type;
factory production control by the manufacturer, including product assessment.
The manufacturer shall always retain the overall control and shall have the necessary means to take
responsibility for the conformity of the product with its declared performance(s).
NOTE The assignment of tasks to the notified bodies and the manufacturer is shown in Table ZA.3.
5.2 Type testing
5.2.1 General
All performances related to characteristics included in this standard shall be determined when the
manufacturer intends to declare the respective performances unless the standard gives provisions for
declaring them without performing tests (e.g. use of previously existing data, CWFT and conventionally
accepted performance).
Assessment previously performed in accordance with the provisions of this standard, may be taken into
account provided that they were made to the same or a more rigorous test method, under the same AVCP
system on the same product or products of similar design, construction and functionality, such that the results
are applicable to the product in question.
NOTE Same AVCP system means testing by an independent third party [only for products covered by
system 1+, 1 and 3], under the responsibility of a notified product certification body.
For the purposes of assessment, the manufacturer's products may be grouped into families, where it is
considered that the results for one or more characteristics from any one product within the family are
representative for those same characteristics for all products within that same family.
Products may be grouped in different families for different characteristics.
Reference to the assessment method standards should be made to allow the selection of a suitable
representative sample.
In addition, the determination of the product type shall be performed for all characteristics included in the
standard for which the manufacturer declares the performance:
at the beginning of the production of a new or modified PMBC (unless a member of the same product
range), or
at the beginning of a new or modified method of production (where this may affect the stated
properties); or
they shall be repeated for the appropriate characteristic(s), whenever a change occurs in the PMBC design, in
the raw material or in the supplier of the components, or in the method of production (subject to the definition
of a family), which would affect significantly one or more of the characteristics.
Where components are used whose characteristics have already been determined, by the component
manufacturer, on the basis of assessment methods of other product standards, these characteristics need not
be re-assessed. The specifications of these components shall be documented.
Products bearing regulatory marking in accordance with appropriate harmonized European specifications may
be presumed to have the performances declared in the DoP, although this does not replace the responsibility
on the PMBC manufacturer to ensure that the PMBC as a whole is correctly manufactured and its component
products have the declared performance values.
5.2.2 Test reports
The results of the determination of the product type shall be documented in test reports. All test reports shall
be retained by the manufacturer for at least 10 years after the last date of production of the PMBC to which
they relate.
5.3 Factory production control (FPC)
5.3.1 General
The manufacturer shall establish, document and maintain an FPC system to ensure that the products placed
on the market comply with the declared performance of the characteristics.
The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the use of
the results to control raw and other incoming materials or components, equipment, the production process and
the product. All the elements, requirements and provisions adopted by the manufacturer shall be documented
in a systematic manner in the form of written policies and procedures.
This factory production control system documentation shall ensure a common understanding of the evaluation
of the constancy of performance and enable the achievement of the required product performances and the
effective operation of the production control system to be checked. Factory production control therefore brings
together operational techniques and all measures allowing maintenance and control of the compliance of the
product with the declared performances of the essential characteristics.
5.3.2 Requirements
5.3.2.1 General
The manufacturer is responsible for organizing the effective implementation of the FPC system. Tasks and
responsibilities in the produ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.