M/102 - CPD: Membranes

EN-ISO 11925-2 specifies a method of test for determining the ignitability ofproducts by direct small flame impingement under zero impressed irradiance usingvertically oriented test specimens. Information on the precision of the testmethod is given in Annex A (informative).Information on testing not essentiallyflat end-use products is given in Annex B (normative).Information on testingperforated end-use products is given in Annex C (normative).

This document specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens.
Information on the precision of the test method is given in Annex A (informative).
Information on testing not essentially flat end-use products is given in Annex B (normative).
Information on testing perforated end-use products is given in Annex C (normative).

This European Standard specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.

This document specifies methods for the determination of the thickness and mass per unit area of plastic and rubber sheets for roof waterproofing.

This European Standard specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick or cut.

This document specifies a method for the determination of tear properties of plastic and rubber sheets for roof waterproofing using a trapezoidal test specimen with a nick or cut.

This document specifies a method for the determination of the gross heat of combustion (QPCS) of
products at constant volume in a bomb calorimeter.
This method is intended to be applied to solid products.
NOTE Liquids can be tested with similar equipment and using conditions described in ASTM D240[1], as
described in IEC 61039[2] using ISO 1928[3] test equipment.
Annex A specifies the calculation of the net heat of combustion, QPCI, when required.
Information on the precision of the test method is given in Annex B.

This document specifies a method for the determination of the gross heat of combustion (QPCS) of products at constant volume in a bomb calorimeter.
This method is intended to be applied to solid products.
NOTE Liquids can be tested with similar equipment and using conditions described in ASTM D240[1], as described in IEC 61039[2] using ISO 1928[3] test equipment.
Annex A specifies the calculation of the net heat of combustion, QPCI, when required.
Information on the precision of the test method is given in Annex B.

This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.

This document specifies definitions and characteristics of flexible plastic and rubber sheets which are intended to be used as damp proofing for buildings, including basement tanking. It specifies the requirements and test methods, and provides for the evaluation of conformity of the products with the requirements of this standard.

This European Standard applies to all liquid-applied water impermeable products, based on polymer modified cementitious mortars, dispersions and reaction resin coatings, used beneath ceramic tiling, for external tile installations on walls and floors and in swimming pools.
This European Standard gives the terminology concerning the products and specifies the test methods and the values of performance requirements for liquid-applied water impermeable products associated with tile adhesives.
This European Standard specifies the evaluation of conformity and the classification and designation of liquid-applied water impermeable products beneath ceramic tiling.
This European Standard does not contain recommendations for the design and installation of ceramic tiles and grouts in combination with water impermeable products.
NOTE 1   Liquid-applied water impermeable products may also be used beneath other types of tiles (natural and agglomerated stones, etc.), where they do not adversely affect these materials.
NOTE 2   The user of this European Standard should be familiar with normal laboratory practice. This European Standard does not purport to address all the safety problems associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any European and national regulatory conditions.

This European Standard applies to all liquid-applied water impermeable products, based on polymer modified cementitious mortars, dispersions and reaction resin coatings, used beneath ceramic tiling, for external tile installations on walls and floors and in swimming pools.
This European Standard gives the terminology concerning the products and specifies the test methods and the values of performance requirements for liquid-applied water impermeable products associated with tile adhesives.
This European Standard specifies the evaluation of conformity and the classification and designation of liquid-applied water impermeable products beneath ceramic tiling.
This European Standard does not contain recommendations for the design and installation of ceramic tiles and grouts in combination with water impermeable products.
NOTE 1   Liquid-applied water impermeable products may also be used beneath other types of tiles (natural and agglomerated stones, etc.), where they do not adversely affect these materials.
NOTE 2   The user of this European Standard should be familiar with normal laboratory practice. This European Standard does not purport to address all the safety problems associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any European and national regulatory conditions.

This European Standard specifies the definitions and requirements of prefabricated polymer modified bituminous thick coatings used for the waterproofing of below ground structures. It applies to both one-component and two-component products. These products can be used with or without inlay.
This European Standard does not apply to products that are to be used for roof waterproofing.

This European Standard specifies the definitions and requirements of prefabricated polymer modified bituminous thick coatings used for the waterproofing of below ground structures. It applies to both one-component and two-component products. These products can be used with or without inlay.
This European Standard does not apply to products that are to be used for roof waterproofing.

EN 13859-1 specifies the characteristics of flexible sheets for underlays which are to be used under roof covering of discontinuous roofs. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

EN 13859-1 specifies the characteristics of flexible sheets for underlays which are to be used under roof covering of discontinuous roofs. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

This European standard specifies the characteristics of flexible sheets for underlays which are to be used under roof covering of discontinuous roofs. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

This European standard specifies the characteristics of flexible sheets for underlays for walls which are to be used in walls behind outside wall coverings in order to avoid penetration of wind and water from outside. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this document.

This European Standard specifies definitions and characteristics for flexible reinforced bitumen sheets for which the intended use is roofing. This covers sheets used as top layers, intermediate layers and underlayers. It does not cover reinforced bitumen sheets for waterproofing used as underlays for discontinuous roofing. It does not cover waterproofing sheets which are intended to be used fully bonded under bituminous products (e.g. asphalt) directly applied at high temperature, specified by EN 14695.

This European Standard specifies definitions and characteristics for flexible reinforced bitumen sheets for which the intended use is roofing. This covers sheets used as top layers, intermediate layers and underlayers. It does not cover reinforced bitumen sheets for waterproofing used as underlays for discontinuous roofing.
This European Standard does not cover waterproofing sheets which are intended to be used fully bonded under bituminous products (e.g. asphalt) directly applied at high temperature, specified by EN 14695.

This European Standard specifies a method for the determination of the resistance of plastic and rubber sheets for waterproofing to cracking when exposed, under static tensile strain, to air containing a definite concentration of ozone and at a definite temperature without the effects of direct light.

This European Standard specifies a method for determining the resistance to peeling of joints between two adjacent sheets of the same plastic or rubber sheets for waterproofing. This test method will be used mainly for testing the joints in mechanically fastened plastic or rubber sheets for waterproofing. The peel strength characterises the optimum joint strength which can be reached for a membrane and a joint technique under laboratory conditions. On roofs the joint strength could be clearly reduced due to the non-optimal conditions (e.g. pressure, temperature, humidity, pollution, workmanship). The requirement for the joint technique at the site is to ensure a permanently tight joint.

This European Standard specifies test methods for the determination of the tensile properties of plastic and rubber sheets for roof waterproofing.

This European Standard specifies a method for the determination of the behaviour of plastic and rubber sheets for waterproofing to folding after exposure at a low temperature.

This European Standard specifies a method for determining the resistance to peeling of joints between two adjacent sheets of the same plastic or rubber sheets for waterproofing.
This test method will be used mainly for testing the joints in mechanically fastened plastic or rubber sheets for waterproofing.
The peel strength characterises the optimum joint strength which can be reached for a membrane and a joint technique under laboratory conditions. On roofs the joint strength could be clearly reduced due to the non-optimal conditions (e.g. pressure, temperature, humidity, pollution, workmanship). The requirement for the joint technique at the site is to ensure a permanently tight joint.

This European Standard specifies test methods for the determination of the tensile properties of plastic and rubber sheets for roof waterproofing.

This European Standard specifies a method for the determination of the resistance of plastic and rubber sheets for waterproofing to cracking when exposed, under static tensile strain, to air containing a definite concentration of ozone and at a definite temperature without the effects of direct light.

This European Standard specifies a method for the determination of the behaviour of plastic and rubber sheets for waterproofing to folding after exposure at a low temperature.

This document specifies the characteristics of flexible sheets of plastic or rubber intended for use as watervapour control layers for buildings and applies to both reinforced and unreinforced products. It specifiesrequirements and test methods and provides for the evaluation of conformity of the products with therequirements of this document.

This European Standard specifies the characteristics of flexible sheets of plastic or rubber intended for use as water vapour control layers for buildings and applies to both reinforced and unreinforced products. It specifies requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.

This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.

This European Standard specifies the definitions and characteristics of plastic and rubber sheets including sheets made out of their blends and alloys (thermoplastic rubber) for which the intended use is roof waterproofing. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
NOTE   For typical materials and applications, see Annex E.

This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail. This European Standard may also be applied for waterproofing.

This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard. This European Standard does not cover related products such as preformed cavity trays, coping and flashings.

This European Standard specifies the determination of the resistance of flexible sheets for roofing to hail using a test for puncture by simulated hail.
This European Standard may also be applied for waterproofing.

This European Standard specifies the characteristics of flexible sheets of plastics and rubber intended for use as damp proof courses for buildings. It specifies the requirements and test methods and provides for the evaluation of conformity of the products with the requirements of this European Standard.
This European Standard does not cover related products such as preformed cavity trays, coping and flashings.

This European Standard specifies two methods (method A and method B) for determining the crack bridge properties of polymer modified bituminous thick coatings for waterproofing. The two test methods may be applied equally.

This European Standard specifies a procedure for determining the watertightness of polymer modified bituminous thick coatings for waterproofing (i.e. the resistance to hydraulic pressure).

This European Standard specifies a procedure for determining the reduction in the thickness of polymer modified bituminous thick coatings due to drying for waterproofing.

This European Standard specifies a procedure for determining the flexibility of polymer modified bituminous thick coatings for waterproofing at low temperature.

This European Standard specifies a procedure for determining the resistance to rain of polymer modified bituminous thick coatings for waterproofing.

This European Standard specifies a procedure for determining the resistance to compression of polymer modified bituminous thick coatings for waterproofing.

This European Standard specifies a procedure for determining the water resistance of polymer modified bituminous thick coatings for waterproofing.

This European Standard specifies a procedure for determining the dimensional stability at a high temperature of polymer modified bituminous thick coatings for waterproofing.

This document specifies a method to test the resistance against water penetration of underlays for discontinuous roofing and for walls.

This European Standard specifies a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing.
NOTE The shearing characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship.

This European Standard specifies a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing.
NOTE   The shearing characteristics of a joint between two widths of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship.

This European Standad specifies a method to test the resistance against water penetration of underlays for discontinuous roofing and for walls.

This European Standard specifies a method of exposing test specimens of plastic and rubber sheets for roofing, free from all external restraint, to liquid chemicals (including water), and methods for determining the changes in properties resulting from such exposure.

This European Standard specifies a method of exposing test specimens of plastic and rubber sheets for roofing, free from all external restraint, to liquid chemicals (including water), and methods for determining the changes in properties resulting from such exposure.