EN ISO 5674:2004
(Main)Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria (ISO 5674:2004)
Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO) drive-shafts - Strength and wear tests and acceptance criteria (ISO 5674:2004)
2006-10-18 EN ISO 5674:2006 effectively replaces EN 1152:1994 considering that the 2004 edition of EN ISO 5674:2004 had to be re-issued for technical reasons.
2005-12-16 SJ: requested OJ flag be removed pending UAP of ISO corrected version.
Migrated from Progress Sheet (TC Comment) (2000-07-10): Revision of EN 1152:1994 (CC/000128) ++ Will be split into 2 items: 1st part will be under VA/ISO lead (prEN ISO 5674-1), the 2nd part will be an ISO document only (NT/030313).
Traktoren und land- und forstwirtschaftliche Maschinen - Schutzeinrichtungen für Gelenkwellen - Festigkeits- und Verschleißprüfungen und Annahmekriterien (ISO 5674:2004)
Diese Internationale Norm beschreibt Laborprüfungen zur Bestimmung von Festigkeit und Verschleiß von Schutzeinrichtungen für Gelenkwellen an Traktoren und Maschinen in der Land- und Forstwirtschaft und deren Annahmekriterien. Die Anwendung in Kombination mit ISO 5673 ist beabsichtigt.
Sie gilt für die Prüfung von Gelenkwellenschutzeinrichtungen und ihren Rückhalteeinrichtungen. Sie gilt nicht für die Prüfung von Schutzeinrichtungen, die zur Benutzung als Stufen gestaltet und konstruiert sind.
Tracteurs et matériels agricoles et forestiers - Protecteurs d'arbres de transmission à cardans de prise de force - Essais de résistance mécanique et d'usure et critères d'acceptation (ISO 5674:2004)
Traktorji ter kmetijski in gozdarski stroji - Zaščita priključnih gredi - Preskusi trdnosti in obrabe ter merila sprejemljivosti (ISO 5674:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2004
1DGRPHãþD
SIST EN 1152:1995
SIST EN 1152:1995/AC:2004
7UDNWRUMLWHUNPHWLMVNLLQJR]GDUVNLVWURML=DãþLWDSULNOMXþQLKJUHGL3UHVNXVL
WUGQRVWLLQREUDEHWHUPHULODVSUHMHPOMLYRVWL ,62
Tractors and machinery for agriculture and forestry - Guards for power take-off (PTO)
drive-shafts - Strength and wear tests and acceptance criteria (ISO 5674:2004)
Traktoren und land- und forstwirtschaftliche Maschinen - Schutzeinrichtungen für
Gelenkwellen - Festigkeits- und Verschleißprüfungen und Annahmekriterien (ISO
5674:2004)
Tracteurs et matériels agricoles et forestiers - Protecteurs d'arbres de transmission a
cardans de prise de force - Essais de résistance mécanique et d'usure et criteres
d'acceptation (ISO 5674:2004)
Ta slovenski standard je istoveten z: EN ISO 5674:2004
ICS:
65.060.01
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 5674
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2004
ICS 65.060.01
English version
Tractors and machinery for agriculture and forestry - Guards for
power take-off (PTO) drive-shafts - Strength and wear tests and
acceptance criteria (ISO 5674:2004)
Tracteurs et matériels agricoles et forestiers - Protecteurs Traktoren und land- und forstwirtschaftliche Maschinen -
d'arbres de transmission à cardans de prise de force - Schutzeinrichtungen für Gelenkwellen - Festigkeits- und
Essais de résistance mécanique et d'usure et critères Verschleißprüfungen (ISO 5674:2004)
d'acceptation (ISO 5674:2004)
This European Standard was approved by CEN on 26 February 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5674:2004 E
worldwide for CEN national Members.
Foreword
This document (EN ISO 5674:2004) has been prepared by Technical Committee ISO/TC 23
"Tractors and machinery for agriculture and forestry" in collaboration with Technical Committee
CEN/TC 144 "Tractors and machinery for agriculture and forestry", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by September 2004, and conflicting national
standards shall be withdrawn at the latest by September 2004.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU
Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 5674:2004 has been approved by CEN as EN ISO 5674:2004 without any
modifications.
ANNEX ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37 EEC
This European Standard has been prepared under a mandate given to CEN by the European
Commission and the European Free Trade Association to provide a means of conforming to
Essential Requirements of the New Approach Directive 98/37 EEC.
Once this standard is cited in the Official Journal of the European Communities under that
Directive and has been implemented as a national standard in at least one Member State,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the
limits of the scope of this standard, a presumption of conformity with the corresponding Essential
Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the product(s)
falling within the scope of this standard.
INTERNATIONAL ISO
STANDARD 5674
Second edition
2004-03-01
Tractors and machinery for agriculture
and forestry — Guards for power take-off
(PTO) drive-shafts — Strength and wear
tests and acceptance criteria
Tracteurs et matériels agricoles et forestiers — Protecteurs d'arbres de
transmission à cardans de prise de force — Essais de résistance
mécanique et d'usure et critères d'acceptation
Reference number
ISO 5674:2004(E)
©
ISO 2004
ISO 5674:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
ISO 5674:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 1
4 General test conditions . 2
4.1 Guard. 2
4.2 Other. 2
5 Test equipment. 2
5.1 General. 2
5.2 Test parameters. 2
6 Tests. 4
6.1 General. 4
6.2 Wear test. 4
6.3 Bearing corrosion test (Perform only if the guard has bearings running in contact with the
PTO-shaft). 4
6.4 Strength tests. 5
6.5 Tests at sub-zero temperature. 8
6.6 Restraining means test at specified temperature. 10
7 Final acceptance criteria . 11
8 Test report. 12
Annex A (normative) Test schedule . 13
Annex B (normative) UV test for plastic guards . 16
Annex C (informative) Typical test report . 17
Annex D (informative) Novel design guard and restraining systems tests. 20
ISO 5674:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5674 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 2, Common tests.
This second edition of ISO 5674 cancels and replaces the first editions of ISO 5674-1:1992 and
ISO 5674-2:1992, of which it constitutes a technical revision.
iv © ISO 2004 – All rights reserved
ISO 5674:2004(E)
Introduction
This document is a type C standard as stated in ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.
INTERNATIONAL STANDARD ISO 5674:2004(E)
Tractors and machinery for agriculture and forestry — Guards
for power take-off (PTO) drive-shafts — Strength and wear tests
and acceptance criteria
1 Scope
This International Standard specifies laboratory tests for determining the strength and wear resistance of
guards for power take-off (PTO) drive-shafts on tractors and machinery used in agriculture and forestry, and
their acceptance criteria. It is intended to be used in combination with ISO 5673.
It is applicable to the testing of PTO drive-shaft guards and their restraining means. It is not applicable to the
testing of guards designed and constructed to be used as steps.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
1)
ISO 500 (all parts), Agricultural tractors
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.