This document specifies safety requirements and their verification for design and construction of, i.e. self-propelled, mounted, semi-mounted and trailed, wood chippers used in forestry, agriculture, horticulture and landscaping.
This document applies to chippers, used when stationary, which are manually loaded with wood through a horizontal or near horizontal infeed chute and where the infeed action is performed by the chipping components acting as infeed components or by separate integrated infeed components such as rollers or conveyors integral to the infeed chute. Wood chippers may be powered either by an external power take-off, hydraulics etc. or by an integral power source such as an internal combustion engine.
This document does not cover:
-   requirements relating to national road regulations arising from transport between work sites;
-   hazards arising from any self-propelled function;
-   hazards arising from the transmission of power from an external power source - e.g. power take-off drive shafts;
-   any machines where the infeed chute is fitted with an extension table or an integrated conveyor that is protruding beyond the outermost lower edge of the infeed chute and the Lower Protective Device of the infeed chute;
-   hazards arising from the engine pull starting of an integral power source;
-   hazards arising from mechanical loading;
-   vertical infeed chute chippers;
-   electromagnetic aspects of the chippers;
-   shredders/chippers to be covered by EN 13683;
-   any machines that are only loaded mechanically;
-   additional mechanical discharge systems for woodchips which are not part of the chipping mechanism e.g. conveyors.
For machines that can be both manually and mechanically loaded, this document is only covering the safety of the manual loading.
NOTE 1   Any additional requirements related to use with both mechanical and manual feed that could affect safe use or which are necessary to maintain the integrity of protective devices are outside the scope of this document. Such additional measures are intended to be determined by risk assessment carried out by the manufacturer.
This document deals with all significant hazards, hazardous situations and events relevant to wood chippers, when they are used as intended and under the conditions foreseeable by the manufacturer (see Annex A).
In addition, it specifies the type of information to be provided by the manufacturer on the safe use of these machines.
It is not applicable to environmental hazards (except noise).
NOTE 2   The noise test code described in this standard does not comply with the outdoor noise directive 2000/14/EC.
This document is not applicable to wood chippers which are manufactured before the date of publication of this document by CEN.

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies to wheeled and/or track-laying self-propelled agricultural and forestry vehicles when used on public roads. It specifies the definitions, construction and performance requirements and the means for verification of braking systems on vehicles with a maximum design speed not exceeding 60 km/h.
Following items are excluded from the scope of this document:
-   coupling force control;
-   endurance braking systems;
-   Anti-Lock Braking Systems and EBS;
-   vacuum braking systems;
-   safety related parts of complex electronic control systems;
-   trailer braking control systems.
NOTE   For assisted trailer braking the EU Regulation 2015/68 can be used but before including these requirements into this document, an additional review of 2015/68 is needed.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2019-11-12 JF TC is reviewing editorially the Annex ZA and is preparing the information on significant changes to be put in the Foreword

  • Amendment
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies safety requirements and their verification for the design and construction of power take-off (PTO) drive shafts and their guards linking a tractor or self-propelled machinery to the first fixed bearing of recipient machinery. It describes methods for the elimination or reduction of risks which need specific requirements including such risks arising from misuse, reasonably foreseeable by the manufacturer. It is applicable only to those PTO drive shafts and guards mechanically linked to the shaft by at least two bearings.
In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
This document does not deal with:
-   the guards totally covering, but not mechanically linked to, the PTO drive shaft;
-   the mechanical characteristics of PTO drive shafts, overrun devices and torque limiters;
-   general hazards which are dealt with in EN ISO 4254-1:2015 (see introduction).
Environmental aspects have not been considered in this document.
This document is not applicable to PTO drive shafts and their guards which are manufactured before the date of publication of this document by CEN.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies safety requirements and their verification for the design and construction of trailers with a tipping body, balanced or semi-mounted, used in agriculture, as defined in 3.1. It includes also hook-lift trailers and trailers with conveyor device as defined in 3.9.
This European Standard does not deal with trailers equipped with pick-up devices and/or rear spreading devices.
Trailers with a load push/push-off device, slats or alternating moving floor may be removed from this standard, provided a new work item on loader wagons and forage transport wagons (prEN ISO 4254-17) is accepted.
This European Standard does not give Required Performance Levels for the identified safety functions.
This European Standard, taken together with EN ISO 4254-1, deals with the significant hazards, hazardous situations and events relevant to agricultural trailers, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Table A.1), excepting the hazards arising from:
-   hazards related to conveying devices other than those defined in 3.9.1 and 3.9.2, for example load push/push-off device;
-   hazards related to the environment and road safety;
-   hazards related to braking.
In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
This document is not applicable to trailers which are manufactured before the date of its publication as EN.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies safety requirements and measures for the verification of the design and construction of hand-held, integrally-driven combustion engine hedge trimmers (hereafter referred to as "hedge trimmers") designed to be used by a single operator for trimming hedges and bushes while utilizing one or more linear reciprocating cutter blades.
This document is also applicable to "split-boom" type hedge trimmers and to multi-purpose machines when configured as a hedge trimmer.
It establishes methods for the elimination or reduction of hazards arising from the use of the hedge trimmers. In addition, it specifies the type of information to be provided by the manufacturer on safe working practices.
This document deals with all significant hazards, hazardous situations and events relevant to powered hand-held hedge trimmers when they are used as intended and under the conditions of misuse that are reasonably foreseeable by the manufacturer (see Clause 4).
This document is not applicable to hedge trimmers with an engine displacement over 80 cm3, nor is it applicable to hedge trimmers manufactured before the date of its publication.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European standard specifies the additional requirements for cableless control systems that are used in forestry machinery. The fundamental requirements are defined in the standard prEN 62745. Cableless control systems for the following forestry machines are treated in this standard:
-   forestry cable winches according to ISO 19472, winches for log splitters;
-   self-propelled machinery for forestry according to EN ISO 11850 (machines for felling, moving and debranching, forwarders, log loaders, skidders, processors, harvesting machines, mulchers as well as multipurpose machines of these construction types, as described in ISO 6814); the definitive part of the standard defines essential requirements for the driving function of the machine;
-   mobile yarders for timber logging corresponding to prEN 16517;
-   log splitters and combined firewood splitters according to EN 609 1:2016, 5.9.2.1 Chipping machines according to EN 13525 and chipping machines with mechanical feed systems for the production of woodchips and shredding /grinding machines;
-   forestry boom loader and similar devices that are used on self-propelled machinery and trailers for forestry according to EN ISO 11850 and, as indicated above, for timber transport, timber loading, the loading of forestry goods or forestry products as well as for the handling and arrangement of timber harvesters, felling attachments, machines for felling and moving, attachments, saw heads, gripper-saw combinations with or without load or similar devices and machines, insofar they are not treated in EN 12999. Forestry boom loader can be a component of the forestry machine on which they are mounted.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document, to be used together with EN ISO 4254-1, specifies the safety requirements and their verification for the design and construction of semi-mounted, trailed and self-propelled slurry tankers, including their spreading or injecting devices, intended for spreading or injecting slurry which are operated by either pneumatic or mechanical power. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
When requirements of this document are different from those which are stated in EN ISO 4254-1, the requirements of this document take precedence over the requirements of EN ISO 4254-1 for machines that have been designed and built according the provisions of this document.
This document, taken together with EN ISO 4254-1, deals with all the significant hazards, hazardous situations and events relevant to slurry tankers, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Table A.1), excepting the hazards related to road safety (e.g. steering, braking).
Environmental aspects have not been considered in this document.
This document is not applicable to slurry tankers which are manufactured before the date of its publication as EN.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies principles for the design of highly automated aspects of highly automated machines and vehicles (e.g. agricultural tractors, tractor implement systems, implements and self-propelled machinery) during agricultural field operations. In addition, it provides guidance on the type of information on safe working practices (including information about residual risks) to be provided by the manufacturer.
The purpose of this document is to assist in the provision of safety requirements, means of verification and information for use to ensure an appropriate level of safety for agricultural and forestry tractors and self-propelled machines with functions allowing highly automated operations (see 3.7).
This document deals with all the significant hazards, hazardous situations and events (as listed in Annex A), relevant to agricultural and forestry tractors and self-propelled machines allowing highly automated field operations when used as intended and under the conditions of misuse foreseeable by the manufacturer during normal operation and service.
NOTE 1 While this document gives principles for the design, verification, validation and provision of information for use of a highly automated agricultural machine (HAAM), the detailed specification of requirements for a specific application will be dependent on the machine and its operating conditions. Therefore, the principles for design given in this document need to be extended for specific HAAM by the use of relevant specific (type-C) standards, when available, or by the manufacturer of the machine using risk assessment. Such additional specification of requirements, for design, verification, validation or information for use are outside the scope of this document.
NOTE 2 Safety requirements for specific machines not related to their highly automated operations can be available in machine-specific type-C standards.
This document is not applicable to:
— forestry applications;
— mobile, semi-mobile or stationary machinery used for farm yard or barn operations;
— operations on public roads including relevant requirements for braking and steering systems.
NOTE 3 With respect to implements (e.g. their specific design, functions) and the communication between tractors and implements, additional risks can be relevant and can require additional measures. Such additional measures are outside the scope of this document and are the responsibility of the manufacturer.
This document is not applicable to agricultural and forestry tractors, tractor implement systems, implements and self-propelled machines which are manufactured before the date of its publication.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document, intended to be used together with ISO 4254-1, specifies the safety requirements, and their verification for design and construction of mounted, semi-mounted, trailed or self-propelled seed drills, including the seeding function of combined seed and fertilizer drills, and seed drills with integrated and inseparable powered soil-working tools used in agriculture. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
This document is also applicable to seeding systems where components for seed deposition in the soil, for seed metering and for seed storage are distributed between two or more linked vehicles.
This document deals with all significant hazards (as listed in Annex A), hazardous situations and events relevant to seed drills, when they are used as intended and under the conditions of misuse foreseeable by the manufacturer, excepting the hazards arising from
— electrostatic phenomena,
— external influences on electrical equipment,
— failure of energy supply,
— failure and/or malfunction of the control system,
— inadequate visibility from drivers'/operators' position,
— travelling functions (drive, braking, etc.),
— break down of parts rotating at high speed,
— equipment for loading seeds (and fertilizer), and
— moving parts for power transmission except for strength requirements for guards.
This document is not applicable to
— fertilizer distributors designed only for solid fertilizer application (covered in ISO 4254-8),
— maintenance or repairs carried out by professional service personnel, or
— to environmental hazards (except noise), and
— to seed drills which are manufactured before the date of its publication.
When requirements of this document are different from those which are stated in ISO 4254-1, the requirements of this document take precedence over the requirements of ISO 4254-1 for machines that have been designed and built according to the provisions of this document.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies safety requirements and their verification for design and construction of pedestrian controlled motor mowers with rotary or reciprocating cutting means used in agricultural, forestry and landscaping to cut and/or mulch grass or similar plants or scrub and woody vegetation.
For the purposes of this standard the following types of pedestrian controlled machines are considered to be motor mowers:
-   flail mowers;
-   grassland mowers;
-   scrub clearing machines;
-   sickle bar mowers.
This standard applies also to multipurpose machines when used for cutting or mulching grass or scrub.
Note   When they are used for other operations (e.g. soil working) other standards can apply.
This standard does not cover lawn mowers (see EN ISO 5395 1, EN ISO 5395 2), engine driven brush cutters and grass trimmers (see EN ISO 11806) or other lawn maintenance equipment.
This document deals with significant hazards, hazardous situations and events, as listed in Annex A, relevant to pedestrian controlled motor mowers when used as intended and under conditions of misuse foreseeable by the manufacturer during normal operation and service. Additionally, it specifies the type of information to be provided by the manufacturer on safe working practices.
Environmental aspects (except noise) have not been considered in this standard.
This document is not applicable to motor mowers manufactured before the date of its publication.

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day

1.1   This European Standard, when used together with EN ISO 4254 1 and EN 15811, specifies safety requirements and measures for self-propelled rough-terrain work platforms for orchard’s operations (WPO) operating at a maximum of 3 m high as defined in 3.1, where the vertical projection of the centre of the area of the platform in all platform configurations at the maximum chassis inclination specified by the manufacturer is always inside the tipping lines, used in agriculture, designed to work on unimproved natural terrain and/or disturbed terrain and intended to move at least two persons to working positions in an orchard where they are carrying out fruit picking, thinning out, pruning, or other operations related to orchard from the work platform.
NOTE   For examples of rough-terrain work platforms for orchard’s operations (WPO), see Figures E. 1 to E.3.
This European Standard describes methods for the elimination or reduction of hazards arising from the intended use of these machines in the course of normal operation and service, except hazards related to conveyor belts and elevators for the bin. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
When requirements of this document are different from those which are stated in EN ISO 4254 1, the requirements of this document take precedence over the requirements of EN ISO 4254 1 for machines that have been designed and built according to the provisions of this document.
This European Standard, taken together with EN ISO 4254 1 and EN 15811, deals with all the significant hazards, hazardous situations and events (as listed in Table 1) relevant to WPOs, when they are used as intended and under the conditions of misuse foreseeable by the manufacturer.
It does not cover the hazards arising from:
a)   use in potentially explosive atmospheres;
b)   getting on and off the work platform at changing levels;
c)   environmental aspects;
d)   road safety.
1.2   This European Standard does not apply to:
a)   Mobile Elevating Work Platforms (MEWPs) (see EN 280);
NOTE 1   Figure E.4 gives an example of this type of machine.
b)   boom-type MEWPs (see EN 280);
NOTE 2   Figure E.5 and E.6 give examples of this type of machine.
c)   tail lifts (see EN 1756-1 and EN 1756-2);
d)   mast climbing work platforms (see EN 1495);
e)   lifting tables (see EN 1570-1);
f)   aircraft ground support equipment (see e.g. EN 1915-1 and EN 1915-2);
g)   elevating operator positions on industrial trucks (see EN 1726-2);
h)   unguided work cages suspended from lifting appliances (see e.g. EN 1808);
i)    machines having centre of the area of the platform outside the tipping lines.
NOTE 3   Figure E.7 gives an example of this type of machine.

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4254-5:2018, intended to be used together with ISO 4254‑1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted and trailed power-driven soil-working machines used in agriculture. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
ISO 4254-5:2018 deals with significant hazards (as listed in Annex A), hazardous situations and events relevant to power-driven soil-working machines used as intended and under the conditions foreseeable by the manufacturer (see Clause 4).
ISO 4254-5:2018 is not applicable to
- spading machines, and
- machines fitted with a retractable device making them capable of working between two successive plants in the same row.
ISO 4254-5:2018 is not applicable to environmental hazards. It is not applicable to hazards related to moving parts for power transmission (except for strength requirements for guards and barriers) or to maintenance or repairs carried out by professional service personnel.
NOTE 1 Specific requirements related to road traffic regulations are not taken into account in this document.
NOTE 2 Vibrations are not regarded as a significant hazard in the case of mounted, semi-mounted or trailed machines.
ISO 4254-5:2018 is not applicable to power-driven soil-working machines which are manufactured before the date of its publication.
When requirements of this document are different from those which are stated in ISO 4254‑1, the requirements of this document take precedence over the requirements of ISO 4254‑1 for machines that have been designed and built according to the provisions of this document.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies safety requirements and their verification for the design and construction of pedestrian controlled internal combustion engine powered lawn aerators and scarifiers which are designed for re-generating lawns by, for instance, combing out grass, thatch and moss or cutting vertically into the lawn face using tines which rotate about a horizontal axis. It describes methods of elimination or reduction of hazards arising from their use. In addition, it specifies the type of information to be provided by the manufacturer on safe working practices.
Throughout this document, the term "machine" applies to those machines known as aerators, scarifiers, corers, lawn rakes or grass rakes.
It does not apply to:
-   aerators/scarifiers made from a machine falling within the scope of EN 709:1997+A4:2009 when fitted with an aerating/scarifying implement;
-   non-powered aerators;
-   vertical axis aerators; or
-   those aerators which cut into the soil by means of a reciprocating motion or by water pressure.
It deals with all significant hazards, hazardous situations and events relevant to scarifiers and aerators, when they are used as intended and under the conditions foreseeable by the manufacturer (see Clause 4). Environmental hazards have not been considered in this document.
This document is not applicable to aerators/scarifiers which are manufactured before the date of its publication.

  • Standard
    61 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4254-8:2018, intended to be used together with ISO 4254‑1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted, trailed or self-propelled fertilizer distributors for solid fertilizer application in agriculture and to be used by one operator only, e.g. full width solid fertilizer distributors, solid fertilizer broadcasters, distributors with oscillating tube and line-distributors, as well as solid fertilizer distributors driven by an auxiliary engine. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
ISO 4254-8:2018 deals with all the significant hazards (as listed in Annex A), hazardous situations and events relevant to solid fertilizer distributors, when they are used as intended and under the conditions foreseeable by the manufacturer (see Clause 4), excepting the hazards arising from:
- inadequate lighting of working area;
- inadequate visibility from drivers/operators position;
- inadequate seating;
- travelling functions (drive, braking etc.);
- rolling over;
- equipment for loading fertilizer into the machine;
- an auxiliary engine;
- moving parts for power transmission except for strength requirements for guards.
ISO 4254-8:2018 is neither applicable to maintenance or repairs carried out by professional service personnel nor to environmental hazards (except noise).
ISO 4254-8:2018 is not applicable to the following:
- combined seed and fertilizer drills which create a soil trench and deposit fertilizer in said trench;
- machines for distributing granulated pesticides;
- pedestrian controlled distributors;
- knapsack distributors.
ISO 4254-8:2018 is not applicable to solid fertilizer distributors which are manufactured before the date of its publication.
When requirements of this document are different from those which are stated in ISO 4254‑1, the requirements of this document take precedence over the requirements of ISO 4254‑1 for machines that have been designed and built according to the provisions of this document.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4254-7:2017, when used together with ISO 4254‑1, specifies the safety requirements and their verification for the design and construction of combine harvesters, forage harvesters, cotton harvesters and sugar cane harvesters. It describes methods for the elimination or reduction of hazards arising from the intended use of these machines by one person (the operator) in the course of normal operation and service. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
When provisions of ISO 4254-7:2017 are different from those which are stated in ISO 4254‑1, the provisions of ISO 4254-7:2017 take precedence over the provisions of ISO 4254‑1 for machines that have been designed and built according to the provisions of ISO 4254-7:2017.
ISO 4254-7:2017, taken together with ISO 4254‑1, deals with all the significant hazards (as listed in Table A.1), hazardous situations and events relevant to combine harvesters, forage harvesters, cotton harvesters and sugar cane harvesters, when they are used as intended and under the conditions of misuse that are reasonably foreseeable by the manufacturer (see Annex A). It is not applicable to hazards arising from the presence of persons other than the operator, cleaning of the grain tank, and hazards related to vibrations and moving parts for power transmission, except for strength requirements for guards and barriers. In respect of braking and steering, it is applicable only to the ergonomic aspects (e.g. location of brake pedal and steering wheel); no other aspects related to braking and steering are covered. In the case of trailed harvesters, it is applicable only to hazards related to the working process.
Design requirements for roll-over protective structures (if applicable) are not specified in ISO 4254-7:2017.
Performance levels (or categories) for safety-related parts of control systems in accordance with ISO 25119 or ISO 13849 are not given in ISO 4254-7:2017.
NOTE Specific requirements related to road traffic regulations are not taken into account in ISO 4254-7:2017.
ISO 4254-7:2017 is not applicable to machines manufactured before the date of its publication.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to circular sawing machines for firewood with manual loading and/or unloading with hand operated carriage, hereinafter referred to as "machines", designed to cut solid wood when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
This European Standard is not applicable to:
a)   combined circular sawing machines for firewood with additional units, i.e. log splitting units or circular saw bench units;
NOTE 1   Circular saw benches are dealt with in EN 1870-19:2013.
NOTE 2   Log splitting machines are dealt with in EN 609-1:1999+A2:2009 and EN 609-2:1999+A1:2009.
NOTE 3   A draft is under consideration to cover "combined firewood processors".
b)   machines where the saw blade is capable of tilting;
c)   log sawing machines where the saw unit moves to cut the workpiece;
d)   hand-held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench mounting;
NOTE 4   Hand-held motor-operated electric tools and saw benches to form an integrated whole with a hand-held motor-operated electric tools are covered by EN 60745-1:2009 together with EN 60745-2-5:2010.
For RIC engines driven machines hazard of engine electrical starting systems above 24 V are not dealt with in this standard.
This document is not applicable to machines which are manufactured before the date of its publication as EN.
NOTE 5   Machines covered by this document are listed under 1.1 and/or 1.2 of Annex IV of the Machinery Directive.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    61 pages
    German language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements to be fulfilled by manufacturers of tractors, interchangeable towed equipment and trailers used in agriculture and forestry in order to comply with the obligation to provide non-discriminatory access for independent operators to Repair and Maintenance Information (RMI) and to provide information on On-Board Diagnostic (OBD) systems.
This standard specifies all organisational and technical requirements and means of verification to comply with the EU Regulation 167/2013 and its Delegated Acts with the objectives to allow the fair competition between manufacturers and between operators and to improve the competitiveness and future viability of companies with special regard to Small and Medium-sized Enterprises (SME).
This European Standard is applicable to agricultural and forestry vehicles approved (respectively to be approved) in accordance with the EU Regulation 167/2013.
This European Standard is not applicable to small series vehicles.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is applicable to cabs of agricultural and forestry tractors and self-propelled sprayers. Its purpose is to limit the exposure of the operator (driver) to hazardous substances when applying plant protection products (PPP) and liquid fertilisers. This European Standard specifies different categories of cabs of agricultural and forestry tractors and self-propelled sprayers and the relevant requirements and test procedures in order to limit the exposure of the operator (driver) to hazardous substances when inside the cab. It also specifies the information to be provided by the tractor or self-propelled sprayer manufacturer.
This document does not cover:
-   the exposure linked to fumigants;
-   the category of cab and performance level to be used for any particular application;
-   the actual cab performance in the field applications;
-   the field durability of filters.
This document is not applicable to tractor cabs which are manufactured before the date of its publication as an EN.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard is applicable to filters as part of cabs of categories 2, 3 and 4 of agricultural and forestry tractors and self-propelled sprayers as specified in EN 15695 1 in order to limit the exposure of the operator (driver) to hazardous substances, in agricultural and forestry operations. It specifies requirements, test procedures and the information to be provided by the filter manufacturer.
This standard does not cover:
-   the exposure linked to fumigants;
-   the category of cab and performance level to be used for any particular application;
-   the actual cab performance in the field applications;
-   field durability of filters or filtration systems.
This document is not applicable to filters which are manufactured before the date of its publication as EN.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the safety requirements, and their verification for the design and construction of horizontal and vertical wedge splitters, designed for splitting logs for firewood, irrespective of the nature of the power source used. This standard deals with wedge splitters that are designed so that the splitting operation is activated by one person only, however it is foreseeable that other operators may be working with the machine e.g. for loading or unloading. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
This document deals with all the significant hazards, hazardous situations and hazardous events relevant to these machines when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Table 1).
This document is not applicable to machines that are designed for both cutting into length for splitting and splitting for firewood.
This document is not applicable to wedge splitters which are manufactured before the date of publication of this document by CEN.

  • Standard
    59 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard establishes a uniform format for reporting accidents where the following equipment are involved:
—   agricultural and forestry tractors (NACE code 09.02.03.01);
—   equipment fitted on tractors (e.g. a front – end loader) (NACE code 09.02.99.00);
—   equipment mounted on the tractor (front and/or rear) (NACE code 09.02.99.00);
—   equipment towed by tractors (trailers and machinery) (NACE code 09.02.04.99);
—   self-propelled machinery (NACE code 09.02.03.02);
—   telescopic loaders (NACE code 09.02.03.02);
—   lawn and gardening equipment (NACE code 09.02.99.00);
—   powered hand-held machinery used in agriculture (NACE code 09.02.99.00).
Accidents with this equipment on road use are also covered by this document.
Are excluded from the scope of this document:
—   the above-mentioned equipment when used in another environment than agriculture, forestry and landscape gardening (e.g. tractors used on construction sites);
—   material handling equipment other than telescopic loaders, skid steer loaders, wheel loaders and front-end loaders mounted on tractors.
All profiles of harmed persons should be in the scope. There should be no distinction/exemption between employers, employees, self-employed persons, bystanders or other persons involved in the accident.
Situations that are excluded from the scope of this document:
—   near-miss accidents and other incidents, not resulting in harm;
—   chronic diseases as a result of physical agents.
Fire hazards are only in the Scope for those fire accidents that have caused physical harm.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 4254-14:2016 intended to be used together with ISO 4254‑1, specifies the safety requirements and their verification for the design and construction of mounted, semi-mounted, trailed, and stationary bale wrapper for bales of agricultural harvesting products including wrappers which are combined or integrated with pick-up balers.
It describes methods for the elimination or reduction of hazards arising from the intended use and reasonably foreseeable misuse of these machines by one person (the operator) in the course of normal operation and service.
In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
NOTE 1 Requirements for self-propelled bale wrappers may be added during the next revision of this part of ISO 4254.
NOTE 2 Examples of these machines are given in Annex A.
NOTE 3 Requirements for pick-up balers are specified in ISO 4254‑11.
When requirements of this part of ISO 4254 are different from those which are stated in ISO 4254‑1, the requirements of this part of ISO 4254 take precedence over the requirements of ISO 4254‑1 for machines that have been designed and built according to the requirements of this part of ISO 4254.
This part of ISO 4254, taken together with ISO 4254‑1, deals with all the significant hazards (as listed in Table 1), hazardous situations, and events relevant to mounted, semi-mounted, and trailed bale wrappers including wrappers which are combined with pick-up balers when they are used as intended and under the conditions of misuse that are reasonably foreseeable by the manufacturer (see Clause 4).
ISO 4254-14:2016 is not applicable to the following:
- non-mobile fixed bale wrappers;
- tube/inline wrappers;
- wrapping process that concerns only the circumferential part of the bale and that occurs in the bale chamber;
- the integrity of safety related parts of control systems with regard to the specification of performance levels;
- environmental hazards (except noise), road safety, and hazards related to moving parts for power transmission;
- hazards related to maintenance or repairs carried out by professional service personnel.
NOTE 4 Specific requirements related to road traffic regulations are not taken into account in this part of ISO 4254.
ISO 4254-14:2016 is not applicable to machines manufactured before the date of its publication.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

MINOR AMENDMENT

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    4 pages
    German language
    sale 10% off
    e-Library read for
    1 day

ISO 17989-1:2015 provides guidelines to assist designers and manufacturers of tractors and machinery for agriculture and forestry to integrate sustainability principles, practices and considerations into their organizations and processes. This part of ISO 17989 is specifically applicable to equipment used in the production of food, fibres, fuel and lumber for humans and livestock.
NOTE This part of ISO 17989 includes three different levels for the application: principles, recommendations and additional information (annexes).
ISO 17989-1:2015 is addressed to the organization management and provides guidance for considering sustainability aspects relevant for the organization and the product life cycle. It defines the factory gate as the system boundary (Figure 1).
ISO 17989-1:2015 is not applicable to contractual or regulatory purposes or to registration and certification.
Except when they are closely related to sustainability, this part of ISO 17989 does not address issues of occupational health and safety or operator safety aspects of a machine's design. Designers can find guidance on these issues in other International Standards.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the safety requirements and their verification for the design and construction of hand-held combustion engine powered and back-pack combustion engine powered, garden vacuums and garden blower/vacuums with or without shredding means and garden blowers, designed for one operator only. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
Throughout this European Standard the term 'machine' is used to mean all the types of garden blowers and vacuums covered by it.
This European Standard deals, except for vibration of backpack machines, with all hazards, hazardous situations and events relevant to these machines when they are used as intended and under the conditions foreseen by the manufacturer (see Clause 4).
This European Standard is not applicable to:
- walk-behind, hand-guided (support-wheeled) and ride-on machines;
- mains driven and battery powered blowers and vacuums of combinations thereof;
NOTE   EN 60335-1 [1] and IEC 60335-2-100 [2] give the safety requirements for mains driven blowers and blower vacuums, vacuum cleaners for household and industrial use.
- structural integrity test for blowers and blower vacuums;
- strength test for harnesses and back-pack supports.
This European Standard is not applicable to machines which are manufactured before the date of its publication a

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard is applicable to agricultural and forestry tractors on which provision is made for carrying one person in addition to the driver. It specifies minimum requirements for space and support, specifies roll-over protective structures (ROPS) test procedures and seat belt requirements, by reference to other standards.
It also specifies the information to be provided by the tractor manufacturer.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

2014-12-03: Changes in the European Foreword.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16231-2:2015 specifies a method to determine the centre of gravity of un-laden self-propelled machines, a method to determine the centre of gravity of laden machines and combinations with attachments, and methods to determine the static overturning angle.
NOTE Requirements related to self-protective structures and ROPS are to be dealt with in a separate International Standard.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16230-1:2015 is applicable to tractors and self-propelled ride-on machines, mounted implements, and towed implements used in agriculture and forestry. This part of ISO 16230 specifies general requirements that relate to the protection and safety of operators and bystanders on machines with on-board voltages in the range of 50 V AC to 1000 V AC and 75 V DC to 1500 V DC. This part of ISO 16230 applies to electrical equipment and parts of the electrical equipment on such machines and includes general requirements related to the protection and safety of operators, bystanders, and first responders.
ISO 16230-1:2015 deals with significant hazards, hazardous situations, and events, as listed in Annex A, relevant to this agricultural machinery when used as intended and under the conditions of misuse foreseeable by the manufacturer during normal operation and service.
ISO 16230-1:2015 is not applicable to the following:
- specific design elements of external interfaces (e.g. the interface between a tractor and implement);
- externally powered equipment (e.g. line powered equipment, equipment without on-board power generation);
- purpose built forestry machines;
- stationary electrical generators.
ISO 16230-1:2015 is not applicable to machines which are manufactured before the date of its publication.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 17962:2015 specifies various means of minimizing the environmental effects of fan exhaust from pneumatic systems for vacuum-style sowing agricultural field equipment used for sowing coated seeds.
It is applicable to vacuum-style sowing systems where "dust off" (fugitive) material from seed coatings can mix with fan (blower) intake air and be exhausted into the atmosphere.
ISO 17962:2015 is not applicable to
- conveyance systems between a central tank and remote meters where the air is exhausted at the remote meters, and
- conveyance systems where the meter is at a central tank and the air is exhaust at a ground engaging opening device.
The design principles in this International Standard are not applicable to pneumatic equipment for sowing which was manufactured before the date of its publication.
NOTE National or local requirements can apply which could be more stringent.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16122-4:2015, when used together with ISO 16122‑1, specifies the requirements and test methods for the inspection of fixed and semi-mobile sprayers, when in use.
The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application.
It does not apply to application equipment for spatial treatment (e.g. foggers).
Note that requirements for the protection of inspectors during an inspection are given in ISO 16122‑1.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16122-2:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of horizontal boom sprayers, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application. Requirements for the protection of inspectors during an inspection are given in ISO 16122 1.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16122-3:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of sprayers for bushes and trees, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve a good application. Requirements for the protection of inspectors during an inspection are given in ISO 16122-1.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16122-1:2015 defines the general requirements to be fulfilled for the inspection of all types of sprayers for plant protection products used in agriculture, horticulture, forestry and other areas, except knapsack sprayers (see ISO 19932?1 and ISO 19932?2).
The specific requirements for the different types of sprayers are defined in the relevant specific parts of ISO 16122. When used in conjunction with the relevant sprayer specific part, ISO 16122-1:2015 specifies the requirements and test methods for the in use inspection of sprayers. The requirements relate mainly to the condition of the sprayer with respect to potential risks for the environment and its performance to achieve a good application.
ISO 16122-1:2015 also includes minimum requirements for the preparation of the sprayer for the inspection and the minimum safety requirements with respect to the safety of the inspector (test operator) during the inspection.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16119-4:2014 specifies requirements and the means for their verification for the design and performance of fixed and semi-mobile sprayers, as defined in 3.1 and 3.2, with regard to minimizing the potential risk of environmental contamination during use, including misuse foreseeable by the manufacturer.
This type of spraying system is generally a combination of separate elements (main tank, pump and application unit) that can be assembled in fixed installations (fixed sprayers) or with moving parts (semi-mobile sprayers).
ISO 16119-4:2014 does not apply to application equipment for space/spatial treatments.
ISO 16119-4:2014 is intended to be used with ISO 16119‑1, which gives general requirements common to all the sprayer types covered by ISO 16119. When requirements of ISO 16119-4:2014 are different from those stated in ISO 16119‑1, the requirements of ISO 16119-4:2014 take precedence over the requirements of ISO 16119‑1 for machines within the scope of ISO 16119-4:2014. ISO 16119-4:2014 does not cover safety aspects (see ISO 4254‑6).
ISO 16119-4:2014 is not applicable to sprayers manufactured before the date of its publication.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the safety requirements and their verification for the design and construction of fixed guards to be opened or removed by the use of a tool and interlocking guards with or without guard locking for moving parts of the power transmission on self-propelled ride-on machines and mounted, semi-mounted or trailed machines used in agriculture. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
It deals with the significant hazards (as listed in Annex A), hazardous situations and events relevant for fixed guards to be opened or removed by the use of a tool and interlocking movable guards of moving parts of power transmission used as intended and under the conditions reasonably foreseeable by the manufacturer (see Clause 4 and Clause 5).
It is not applicable to guards of moving parts of the power transmission of:
-   agricultural and forestry tractors,
-   aircraft and air cushion vehicles used in agriculture,
-   lawn and garden equipment, or
-   PTO drive shafts between agricultural and forestry tractors and mounted or towed implements.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard, to be used together with EN ISO 4254-1, specifies the safety requirements and their verification for the design and construction of self-propelled, mounted, semi-mounted and trailed manure spreaders, provided with vertical or horizontal axes rotors rear spreader device or with vertical axes disc rear spreader device. In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
When requirements of this document are different from those which are stated in EN ISO 4254-1, the requirements of this document take precedence over the requirements of EN ISO 4254-1 for machines that have been designed and built according the provisions of this document.
This European Standard, taken together with EN ISO 4254-1, deals with all the significant hazards, hazardous situations and events relevant to manure spreaders, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Table 1), excepting the hazards arising from:
-   vibrations of self-propelled machinery;
-   travelling function of self-propelled machinery;
-   overturning in regard to the protection of the operator at the driving station of a self-propelled machine;
-   hazards related to conveying devices other than those defined in 3.3.1 and 3.3.2, for example load push/push-off device.
NOTE 1   Regarding roll-over protection for self-propelled agricultural machinery, see EN ISO 16231-1.
NOTE 2   This European Standard is neither applicable to environmental hazards nor to road safety. Environmental aspects are dealt with in EN 13080.
This European Standard does not apply to manure spreaders with laterally mounted spreading device as defined in 3.6.
This European Standard is not applicable to manure spreaders which are manufactured before the date of publication of this document by CEN.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 5395-3:2013 specifies safety requirements and their verification for combustion-engine-powered ride-on (seated) rotary lawnmowers and cylinder lawnmowers (hereafter named "lawnmower"), and equipped with: metallic cutting means; and/or non-metallic cutting means with one or more cutting elements pivotally mounted on a generally circular drive unit, where these cutting elements rely on centrifugal force to achieve cutting, and have a kinetic energy for each single cutting element of 10 J or more.
It does not apply to: robotic and remote-controlled lawnmowers, flail mowers, grassland mowers, sickle bar mowers, towed/semi-mounted grass-cutting machines, and scrub-clearing machines; cutting-means assembly when used in combination with an agricultural tractor; electrically powered and battery-powered lawnmowers.
ISO 5395-3:2013 deals with all significant hazards, hazardous situations or events relevant to lawnmowers when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer.
It is not applicable to lawnmowers which are manufactured before the date of publication of this document.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 5395-1:2013 specifies terminology and common test methods used for verification of safety requirements for combustion engine powered rotary lawnmowers and cylinder lawnmowers including pedestrian-controlled (with or without sulky) and ride-on types (hereafter named "lawnmower"), and equipped with: metallic cutting means and/or; non-metallic cutting means with one or more cutting elements pivotally mounted on a generally circular drive unit, where these cutting elements rely on centrifugal force to achieve cutting, and have a kinetic energy for each single cutting element of 10 J or more.
It does not apply to: robotic and remote-controlled lawnmowers, flail mowers, grassland mowers, sickle bar mowers, towed/semi-mounted grass cutting machines, and scrub-clearing machines; cutting-means assembly when used in combination with an agricultural tractor; electrically powered and battery-powered lawnmowers.
Note that IEC 60335-1 together with IEC 60335-2-77, give requirements for pedestrian-controlled walk-behind electrically powered lawnmowers.
ISO 5395-1:2013 is not applicable to lawnmowers which are manufactured before the date of publication of this document.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 5395-2:2013 specifies safety requirements and their verification for combustion-engine-powered pedestrian-controlled (with or without sulky) rotary lawnmowers and cylinder lawnmowers (hereafter named "lawnmower"), and equipped with: metallic cutting means; and/or non-metallic cutting means with one or more cutting elements pivotally mounted on a generally circular drive unit, where these cutting elements rely on centrifugal force to achieve cutting, and have a kinetic energy for each single cutting element of 10 J or more.
It does not apply to: robotic and remote-controlled lawnmowers, flail mowers, grassland mowers, sickle bar mowers, towed/semi-mounted grass-cutting machines, and scrub-clearing machines; electrically powered and battery-powered lawnmowers; pedestrian-controlled lawnmowers with a swing-over handle.
Note that IEC 60335-1 together with IEC 60335-2-77 give requirements for pedestrian-controlled walk-behind electrically powered lawnmowers.
ISO 5395-2:2013 deals with all significant hazards, hazardous situations or events relevant to lawnmowers when used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer.
It is not applicable to lawnmowers which are manufactured before the date of publication of this document.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day

CEN/TC 144 Corrigendum - Editorial modification to 5.2.1.3.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19932-1:2013 specifies the safety and environmental requirements and their means of verification for the design and construction of knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid, with a nominal volume of more than 3 l, for their intended use primarily in agriculture and horticulture.
It does not apply to knapsack mistblowers according to ISO 28139.
ISO 19932-1:2013 deals with all significant hazards, hazardous situations and hazardous events relevant to knapsack sprayers when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, excepting the hazards arising from: static electricity; explosion or fire from chemicals for spraying; and insufficient structural integrity.
ISO 19932-1:2013 is not applicable to knapsack sprayers which are manufactured before the date of its publication.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day