EN 485-1:2016

Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery

This document specifies the technical conditions for inspection and delivery of wrought aluminium and wrought aluminium alloy sheet, strip and plate for general applications. It also includes provisions for ordering and testing.
It applies to products with a thickness over 0,20 mm up to and including 400 mm.
For many special applications of aluminium strip, sheet and plate, specific European Standards exist, where different or additional requirements are formulated and the appropriate alloys and tempers are selected: see Annex A. Most of these special European Standards refer to provisions of this document.
The selection of the relevant special European Standards is under the responsibility of the purchaser.
Whenever the application involves special properties, such as corrosion resistance, toughness, fatigue strength, surface appearance and welding properties, the user should consult the supplier and consider the relevant special European Standard, as applicable.

Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 1: Technische Lieferbedingungen

Dieses Dokument legt die Technischen Lieferbedingungen für Bänder, Bleche und Platten aus Aluminium und Aluminium-Knetlegierungen für allgemeine Anwendungen fest. Es enthält außerdem Festlegungen hinsichtlich der Bestellung und Prüfung.
Es gilt für Erzeugnisse mit einer Dicke über 0,20 mm bis 400 mm.
Für viele besondere Anwendungen von Aluminiumbändern, -blechen und -platten bestehen spezielle Euro¬päische Normen, in denen andere oder ergänzende Anforderungen aufgeführt und geeignete Legierungen und Werkstoffzustände ausgewählt sind, siehe Anhang A. Die meisten dieser speziellen Europäischen Normen beziehen sich auf Festlegungen aus dem vorliegenden Dokument.
Die Verantwortung für die Auswahl der geeigneten speziellen Europäischen Normen liegt beim Käufer.
Sofern die Anwendung spezielle Eigenschaften, wie z. B. Korrosionsbeständigkeit, Zähigkeit, Dauerfestigkeit, Oberflächenbeschaffenheit und Schweißeigenschaften, einschließt, sollte der Anwender den Lieferanten hinzuziehen und die entsprechende spezielle Europäische Norm, wenn zutreffend, berücksichtigen.

Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 1: Conditions techniques de contrôle et de livraison

Le présent document spécifie les conditions techniques de contrôle et de livraison des tôles, bandes et tôles épaisses en aluminium corroyé et alliages d’aluminium corroyés pour des applications générales. Il inclut également des dispositions concernant la passation de commande et les essais.
Il s’applique aux produits d’épaisseur supérieure à 0,20 mm et inférieure ou égale à 400 mm.
En ce qui concerne de nombreuses applications spéciales des bandes, tôles et tôles épaisses d’aluminium, des Normes européennes particulières existent, dans lesquelles des exigences différentes ou supplémentaires sont formulées et où les alliages et états métallurgiques adaptés sont sélectionnés : voir Annexe A. La plupart de ces Normes européennes particulières renvoient aux dispositions du présent document.
Le choix des Normes européennes particulières correspondantes relève de la responsabilité de l’acheteur.
Lorsque l’application implique des propriétés particulières, tels que résistance à la corrosion, ténacité, résistance à la fatigue, aspect de surface et propriétés de soudure, il convient que l’utilisateur consulte le fournisseur et prenne en compte, selon le cas, la Norme européenne particulière correspondante.

Aluminij in aluminijeve zlitine - Pločevine, trakovi in plošče - 1. del: Tehnični pogoji za pregled in dobavo

Ta dokument določa tehnične pogoje za pregled in dobavo pločevin, trakov ter plošč iz gnetenega aluminija in aluminijeve zlitine za splošno uporabo. Vključuje določbe za naročanje in preskušanje.
Uporablja se za proizvode z debelino od 0,20 mm do vključno 400 mm.
Za mnoge posebne uporabe aluminijevega traku, pločevin in plošč obstajajo posebni evropski standardi, kjer so navedene drugačne ali dodatne zahteve ter izbrane ustrezne zlitine in popuščena stanja (glej dodatek A). Večina teh posebnih evropskih standardov se nanaša na določbe tega dokumenta.
Kupec je odgovoren za izbiro ustreznih posebnih evropskih standardov.
Kadar uporaba vključuje posebne lastnosti, kot so odpornost na korozijo, trpežnost, nihajna trdnost, površinski videz in varilne lastnosti, se mora uporabnik posvetovati z dobaviteljem in upoštevati ustrezen poseben evropski standard, kot se uporablja.

General Information

• Status: Published
• Publication Date: 26-Jul-2016
• ICS: 77.150.10 - Aluminium products
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 7 - Sheets, strips and plates
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 15-Jun-2022
• Ref Project: SIST EN 485-1:2016 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery

Relations

• Replaces: EN 485-1:2008+A1:2009 - Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery
• Effective Date: 03-Jul-2013

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2016
1DGRPHãþD
SIST EN 485-1:2008+A1:2010
$OXPLQLMLQDOXPLQLMHYH]OLWLQH3ORþHYLQHWUDNRYLLQSORãþHGHO7HKQLþQLSRJRML
]DSUHJOHGLQGREDYR
Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for
inspection and delivery
Aluminium und Aluminiumlegierungen - Bänder, Bleche und Platten - Teil 1: Technische
Lieferbedingungen
Aluminium et alliages d'aluminium - Tôles, bandes et tôles épaisses - Partie 1:
Conditions techniques de contrôle et de livraison
Ta slovenski standard je istoveten z: EN 485-1:2016
ICS:
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 485-1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2016
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 485-1:2008+A1:2009
English Version
Aluminium and aluminium alloys - Sheet, strip and plate -
Part 1: Technical conditions for inspection and delivery
Aluminium et alliages d'aluminium - Tôles, bandes et Aluminium und Aluminiumlegierungen - Bänder,
tôles épaisses - Partie 1: Conditions techniques de Bleche und Platten - Teil 1: Technische
contrôle et de livraison Lieferbedingungen
This European Standard was approved by CEN on 12 June 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 485-1:2016 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 6
4 Ordering information . 6
5 Requirements . 8
6 Test methods . 9
7 Inspection document . 16
8 Marking of products . 16
9 Packaging . 16
10 Complaints of non conformity . 16
Annex A (normative) European Standards for strip, sheet and plate of special form and for
special applications . 17
Bibliography . 18

European foreword
This document (EN 485-1:2016) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2017, and conflicting national standards shall be withdrawn
at the latest by January 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 485-1:2008+A1:2009.
EN 485 comprises the following parts under the general title “Aluminium and aluminium alloys — Sheet, strip
and plate”:
— Part 1: Technical conditions for inspection and delivery
— Part 2: Mechanical properties
— Part 3: Tolerances on dimensions and form for hot-rolled products
— Part 4: Tolerances on shape and dimensions for cold-rolled products
CEN/TC 132 affirms it is policy that in the case when a patentee refuses to grant licences on standardized
standard products under reasonable and not discriminatory condition, then this product should be removed
from the corresponding document.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
1 Scope
This document specifies the technical conditions for inspection and delivery of wrought aluminium and
wrought aluminium alloy sheet, strip and plate for general applications. It also includes provisions for
ordering and testing.
It applies to products with a thickness over 0,20 mm up to and including 400 mm.
For many special applications of aluminium strip, sheet and plate, specific European Standards exist, where
different or additional requirements are formulated and the appropriate alloys and tempers are selected: see
Annex A. Most of these special European Standards refer to provisions of this document.
The selection of the relevant special European Standards is under the responsibility of the purchaser.
Whenever the application involves special properties, such as corrosion resistance, toughness, fatigue
strength, surface appearance and welding properties, the user should consult the supplier and consider the
relevant special European Standard, as applicable.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form
for hot-rolled products
EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations
EN 541, Aluminium and aluminium alloys - Rolled products for cans, closures and lids - Specifications
EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3:
Chemical composition and form of products
EN 602, Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished products
used for the fabrication of articles for use in contact with foodstuff
EN 603 (all parts), Aluminium and aluminium alloys — Wrought forging stock
EN 683-1, Aluminium and aluminium alloys - Finstock - Part 1: Technical conditions for inspection and delivery
EN 851, Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils -
Specifications
EN 941, Aluminium and aluminium alloys - Circle and circle stock for the production of general applications -
Specifications
EN 1386, Aluminium and aluminium alloys - Tread plate - Specifications
EN 1396, Aluminium and aluminium alloys - Coil coated sheet and strip for general applications - Specifications
EN 1669, Aluminium and aluminium alloys - Test methods - Earing test for sheet and strip
EN 2004-1, Aerospace series - Test methods for aluminium and aluminium alloy products - Part 1:
Determination of electrical conductivity of wrought aluminium alloys
EN 10204, Metallic products - Types of inspection documents
EN 12258-1, Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms
EN 12392, Aluminium and aluminium alloys - Wrought products and cast products - Special requirements for
products intended for the production of pressure equipment
EN 12482-1, Aluminium and aluminium alloys - Reroll stock for general applications - Part 1: Specifications for
hot rolled reroll stock
EN 12482-2, Aluminium and aluminium alloys - Reroll stock for general applications - Part 2: Specifications for
cold rolled reroll stock
EN 13195, Aluminium and aluminium alloys - Specifications for wrought and cast products for marine
applications (shipbuilding, marine and offshore)
EN 13981-2, Aluminium and aluminium alloys - Products for structural railway applications - Technical
conditions for inspection and delivery - Part 2: Plates and sheets
EN 14121, Aluminium and aluminium alloys - Sheet, strip and plate for electrotechnical applications
EN 14242, Aluminium and aluminium alloys - Chemical analysis - Inductively coupled plasma optical emission
spectral analysis
EN 14286, Aluminium and aluminium alloys - Weldable rolled products for tanks for the storage and
transportation of dangerous goods
EN 14287, Aluminium and aluminium alloys - Specific requirements on the chemical composition of products
intended to be used for the manufacture of packaging and packaging components
EN 14361, Aluminium and aluminium alloys - Chemical analysis - Sampling from metal melts
EN 14392, Aluminium and aluminium alloys - Requirements for anodised products for use in contact with
foodstuff
EN 15088, Aluminium and aluminium alloys - Structural products for construction works - Technical conditions
for inspection and delivery
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1)
EN ISO 7438, Metallic materials - Bend test (ISO 7438)
EN ISO 20482, Metallic materials - Sheet and strip - Erichsen cupping test (ISO 20482)
ISO 9591, Corrosion of aluminium alloys — Determination of resistance to stress corrosion cracking
ASTM G34, Standard Test Method for Exfoliation Corrosion Susceptibility in 2XXX and 7XXX Series Aluminum
Alloys (EXCO Test)
ASTM G47, Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and
7XXX Aluminum Alloy Products
ASTM G66, Standard Test Method for Visual Assessment of Exfoliation Corrosion Susceptibility of 5XXX Series
Aluminum Alloys (ASSET Test)
ASTM G67, Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series
Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12258-1 and the following apply.
3.1
sheet/plate
flat rolled product of rectangular cross-section with uniform thickness between 0,20 mm and 6 mm for sheet
or above 6 mm for plate, supplied in straight lengths (i.e. flat) usually with trimmed or sawn edges
Note 1 to entry: For sheet, the thickness does not exceed one-tenth of the width.
Note 2 to entry: Corrugated, embossed (with patterns, for example grooves, ribs, checkers, tears, buttons, lozenges),
coated, edge conditioned and perforated products in this general form when derived from sheet as defined above are
classified as sheet.
Note 3 to entry: Flat sheets and plates material between 3 mm and 15 mm are sometimes called “shate”.
3.2
strip
flat rolled product of rectangular cross-section with uniform thickness over 0,20 mm, supplied in coils
usually with trimmed edges
Note 1 to entry: The thickness does not exceed one-tenth of the width.
Note 2 to entry: Corrugated, embossed (with patterns, for example grooves, ribs, checkers, tears, buttons, lozenges),
coated, edge conditioned and perforated products in this general form when derived from sheet as defined above are
classified as sheet.
Note 3 to entry: “Strip” is sometimes called “coil”.
3.3
order document
document or set of documents agreed between supplier and purchaser at the time of ordering
Note 1 to entry: An order document can be an order of the purchaser confirmed by the supplier or a quotation of the
supplier confirmed by the purchaser.
4 Ordering information
The order document shall contain the following:
a) form and type of product
...