EN 851:2022
(Main)Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
Aluminium and aluminium alloys - Circle and circle stock for the production of culinary utensils - Specifications
This document specifies the particular requirements for wrought aluminium and aluminium alloys in the form of circle or circle stock for culinary utensils applications.
This document is applicable to:
— circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and including 12 mm and with a diameter from 100 mm up to and including 1 600 mm;
NOTE Circles with a diameter up to 1 000 mm can be produced by blanking.
— hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a width up to 1 600 mm.
This document is not applicable to slugs for impact extrusions which are dealt with in other European Standards.
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung von Küchengeschirr - Spezifikationen
Dieses Dokument legt die besonderen Anforderungen für Ronden und Rondenvormaterial aus Aluminium-Knetlegierung und Aluminiumlegierungen fest, die zur Herstellung von Küchengeschirr eingesetzt werden.
Dieses Dokument ist anzuwenden für:
— Ronden, die aus kalt- bzw. warmgewalztem Rondenvormaterial mit einer Dicke von 0,2 mm bis 12 mm und einem Durchmesser von 100 mm bis 1 600 mm hergestellt werden;
ANMERKUNG Ronden mit einem Durchmesser von bis zu 1 000 mm können durch Stanzen hergestellt werden.
— kalt- bzw. warmgewalztes Rondenvormaterial mit einer Dicke von 0,2 mm bis 12 mm und einer Breite bis 1 600 mm.
Dieses Dokument ist nicht anzuwenden für Butzen zum Fließpressen, die in anderen Europäischen Normen behandelt werden.
Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications culinaires - Spécifications
Le présent document spécifie les exigences particulières applicables à l'aluminium et aux alliages d'aluminium corroyés sous forme de disques ou d'ébauches pour disques destinés à la fabrication d’ustensiles culinaires.
Il s'applique aux :
- disques fabriqués à partir d'ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 0,2 mm et 12 mm inclus, et de diamètre compris entre 100 mm et 1 600 mm inclus ;
NOTE Les disques dont le diamètre n'excède pas 1 000 mm peuvent être fabriqués par poinçonnage.
- ébauches pour disques laminées à chaud ou à froid, d'épaisseur comprise entre 0,2 mm et 12 mm inclus et de largeur inférieure ou égale à 1 600 mm.
Le présent document ne s'applique pas aux pions de filage par choc qui sont traités dans d'autres Normes européennes.
Aluminij in aluminijeve zlitine - Rondele in polizdelki za izdelavo jedilnih pripomočkov in posode - Specifikacije
Ta dokument določa posamezne zahteve za gneteni aluminij in aluminijeve zlitine v obliki rondel ali polizdelkov za uporabo pri izdelavi jedilnih pripomočkov in posode.
Ta standard se uporablja za:
– rondele, izdelane iz vroče ali hladno valjanih polizdelkov z debelino od 0,2 mm do vključno 12 mm in s premerom od 100 mm do vključno 1600 mm.
OPOMBA: Rondele s premerom do 1000 mm je mogoče izdelati s finim rezanjem.
– vroče ali hladno valjane polizdelke z debelino od 0,2 mm do vključno 12 mm in s premerom do 1600 mm.
Ta dokument se ne uporablja za kovinske palice za udarno iztiskanje, ki so obravnavane v drugih evropskih standardih.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2022
Nadomešča:
SIST EN 851:2014
Aluminij in aluminijeve zlitine - Rondele in polizdelki za izdelavo jedilnih
pripomočkov in posode - Specifikacije
Aluminium and aluminium alloys - Circle and circle stock for the production of culinary
utensils - Specifications
Aluminium und Aluminiumlegierungen - Ronden und Rondenvormaterial zur Herstellung
von Küchengeschirr - Spezifikationen
Aluminium et alliages d'aluminium - Disques et ébauches pour disques pour applications
culinaires - Spécifications
Ta slovenski standard je istoveten z: EN 851:2022
ICS:
77.150.10 Aluminijski izdelki Aluminium products
97.040.60 Kuhinjska posoda, jedilni Cookware, cutlery and
servisi in jedilni pribor flatware
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 851
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 77.150.10 Supersedes EN 851:2014
English Version
Aluminium and aluminium alloys - Circle and circle stock
for the production of culinary utensils - Specifications
Aluminium et alliages d'aluminium - Disques et Aluminium und Aluminiumlegierungen - Ronden und
ébauches pour disques pour applications culinaires - Rondenvormaterial zur Herstellung von
Spécifications Küchengeschirr - Spezifikationen
This European Standard was approved by CEN on 14 February 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 851:2022 E
worldwide for CEN national Members.
EN 851:2021 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Technical conditions for inspection and delivery . 5
4.1 General. 5
4.2 Orders or tenders . 5
5 Mechanical properties . 6
5.1 General. 6
5.2 Earing . 6
6 Tolerances on dimensions and form . 6
6.1 General. 6
6.2 Diameter . 6
6.3 Thickness . 7
6.4 Tolerances on flatness for circle . 7
6.5 Edge burr tolerances for circle . 7
7 Other requirements . 7
Bibliography . 12
European foreword
This document (EN 851:2022) has been prepared by Technical Committee CEN/TC 132 “Aluminium
and aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 851:2014.
In comparison with to the previous edition, Clause 6.4 was modified.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
1 Scope
This document specifies the particular requirements for wrought aluminium and aluminium alloys in
the form of circle or circle stock for culinary utensils applications.
This document is applicable to:
— circles made out of hot or cold rolled circles stock, with a thickness from 0,2 mm up to and
including 12 mm and with a diameter from 100 mm up to and including 1 600 mm;
NOTE Circles with a diameter up to 1 000 mm can be produced by blanking.
— hot or cold-rolled circle stock with a thickness from 0,2 mm up to and including 12 mm and with a
width up to 1 600 mm.
This document is not applicable to slugs for impact extrusions which are dealt with in other European
Standards.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 485-1:2016, Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for
inspection and delivery
EN 485-2, Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties
EN 485-3, Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and
form for hot-rolled products
EN 485-4, Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and
dimensions for cold-rolled products
EN 515, Aluminium and aluminium alloys - Wrought products - Temper designations
EN 602, Aluminium and aluminium alloys - Wrought products - Chemical composition of semi-finished
products used for the fabrication of articles for use in contact with foodstuff
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
circle
circular flat product obtained by circular sawing or shearing, or by
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.