FprEN 4880

Aerospace series - General technical specification for standard parts

Luft- und Raumfahrt - Allgemeine technische Spezifikationen für Normteile

Série aérospatiale - Spécification technique générale pour les pièces normalisées

Aeronavtika - Splošna tehnična specifikacija za standardizirane dele

General Information

• Status: Not Published
• Publication Date: 15-Aug-2023
• ICS: 49.035 - Components for aerospace construction
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3/S 2 - Fasteners
• Current Stage: 6055 - CEN Ratification completed (DOR) - Publishing
• Start Date: 03-Mar-2023
• Completion Date: 03-Mar-2023
• Ref Project: kSIST FprEN 4880:2022 - Aerospace series - General technical specification for standard parts

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 4880:2020
01-oktober-2020
Aeronavtika - Splošna tehnična specifikacija za standardizirane dele
Aerospace series - General technical specification for standard parts
Luft- und Raumfahrt - Allgemeine technische Spezifikationen für Normteile
Série aérospatiale - Spécification technique générale pour les pièces standard
Ta slovenski standard je istoveten z: prEN 4880
ICS:
49.035 Sestavni deli za letalsko in Components for aerospace
vesoljsko gradnjo construction
oSIST prEN 4880:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 4880:2020
---------------------- Page: 2 ----------------------
oSIST prEN 4880:2020
DRAFT
EUROPEAN STANDARD
prEN 4880
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2020
ICS 49.035
English Version
Aerospace series - General technical specification for
standard parts

Série aérospatiale - Spécification technique générale Luft- und Raumfahrt - Allgemeine technische

pour les pièces standard Spezifikationen für Normteile

This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-

STAN.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations

which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 4880:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 4880:2020
prEN 4880:2020 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms and definitions ................................................................................................................................... 4

4 Requirements ................................................................................................................................................... 5

4.1 Production engineering ................................................................................................................................ 5

4.2 Materials ............................................................................................................................................................. 5

4.3 Performance requirements ......................................................................................................................... 5

4.4 Workmanship ................................................................................................................................................... 5

4.5 Interchangeability .......................................................................................................................................... 5

4.6 Marking ............................................................................................................................................................... 6

4.7 Protective treatment and surface finish (protective finish) ........................................................... 6

4.8 Acceptance test report .................................................................................................................................. 6

4.9 Standard ambient test conditions ............................................................................................................. 6

5 Qualifications and quality assurance provisions ................................................................................ 6

5.1 Approval of manufacturers ......................................................................................................................... 6

5.2 Responsibility for Inspection ...................................................................................................................... 6

5.3 Classification of Inspection .......................................................................................................................... 6

5.4 Qualification test ............................................................................................................................................. 7

5.5 First Article Inspection .................................................................................................................................. 7

5.6 Conformance/Acceptance test ................................................................................................................... 7

6 Conditions on delivery .................................................................................................................................. 7

6.1 Packaging ........................................................................................................................................................... 7

6.2 Marking of packages ...................................................................................................................................... 8

6.3 Unit and transport packages ....................................................................................................................... 8

7 Quality management system ....................................................................................................................... 8

Annex A (informative) Record of revisions ........................................................................................................ 9

Bibliography ................................................................................................................................................................. 10

---------------------- Page: 4 ----------------------
oSIST prEN 4880:2020
prEN 4880:2020 (E)
European foreword

This document (prEN 4880:2020) has been prepared by the Aerospace and Defence Industries

Association of Europe - Standardization (ASD-STAN).

After enquiries and votes carried out in accordance with the rules of this Association, this Standard has

received the approval of the National Associations and the Official Services of the member countries of

ASD-STAN, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
---------------------- Page: 5 ----------------------
oSIST prEN 4880:2020
prEN 4880:2020 (E)
1 Scope

This document specifies the minimum requirements for the qualification, acceptance, delivery and

inspection of standard parts by the aerospace industry and its manufacturers.

This document is valid for standard parts and their assemblies as described in a product standard, if

mentioned therein. This specification can also be applied to other parts when specifically invoked by

the terms of delivery.

Parts/sections of this document are not applicable in cases where the product standard stipulates

requirements that differ from this specification.
2 Normative references

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments) applies.

EN 2424, Aerospace series - Marking of aerospace products
EN 9130:2020, Aerospace series — Quality systems — Record retention
ISO 16228, Fasteners — Types of inspection documents
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.

ISO and IEC maintain terminological databases for use in standardization at the following addresses:

— ISO Online browsing platform: available at http://www.iso.org/obp
— IEC Electropedia: available at http://www.electropedia.org/
3.1
standard part
parts as defined by a product standard, which may be single or assemblies
3.2
assembly
individual parts that are connected to each other
3.3
production lot (batch)

parts or assemblies, which shall have the same physical characteristics (dimensions, materials,

manufacturing methods, heat treatment, surface finish, etc.), being manufactured under the same

conditions and submitted together for inspection
...