EN 1555-3:2010+A1:2012

Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings

This !European Standard" specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for piping systems in the field of the supply of gaseous fuels.
It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with Parts 1, 2, 4 and 5 of EN 1555, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   a maximum operating pressure, MOP, up to and including 10 bar;
b)   an operating temperature of 20 °C as reference temperature.
NOTE 1   For other operating temperatures, derating coefficients should be used; see EN 1555-5.
EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
This European Standard is applicable for fittings of the following types:
c)   electrofusion socket fittings;
d)   electrofusion saddle fittings;
e)   spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
f)   mechanical fittings.
The fittings can e.g. be in the form of couplers, equal and reduced tees, reducers, bends or caps.

Kunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 3: Formstücke

Systèmes de canalisations en plastique pour la distribution de combustibles gazeux - Polyéthylène (PE) - Partie 3 : Raccords

La présente !Norme européenne" spécifie les caractéristiques des raccords soudables en polyéthylène (PE) ainsi que celles des raccords mécaniques fabriqués pour les systèmes de canalisations destinées à la distribution de combustibles gazeux.
Elle spécifie également les paramètres d'essai des méthodes d'essai auxquelles la présente norme fait référence.
Conjointement avec les parties 1, 2, 4 et 5 de l’EN 1555, elle s'applique aux raccords en PE et à leurs assemblages, ainsi qu'à leurs assemblages avec des composants en PE et autres matières, destinés à être utilisés dans les conditions suivantes :
a)   une pression maximale de service, MOP, jusque et y compris 10 bar 1)  ;
b)   une température de service de 20 °C, comme température de référence.
NOTE 1   Pour d'autres températures de service, il convient d’utiliser des facteurs de réduction, voir l’EN 1555 5.
L’EN 1555 (toutes les parties) concerne une gamme de pressions maximales de service et donne les exigences concernant les couleurs et les additifs.
NOTE 2   Il est de la responsabilité de l'acheteur ou du prescripteur de faire le choix approprié de ces différents aspects, en prenant en compte les exigences particulières et les règlements nationaux correspondants ainsi que les pratiques ou codes de pose.
La présente Norme européenne est applicable aux raccords des types suivants :
a)   raccords à emboîture électrosoudable ;
b)   selles électrosoudables ;
c)   raccords à bout mâle (pour soudage bout à bout à l'aide d'outils chauffants et pour soudage par emboîture électrosoudable) ;
d)   raccords mécaniques.
Les raccords peuvent être, par exemple, des manchons, des tés égaux, des tés réduits, des réductions, des coudes ou des bouchons.

Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Polietilen (PE) - 3. del: Fitingi

Ta evropski standard določa značilnosti spojnih fitingov iz polietilena (PE) in mehaničnih fitingov za cevne sisteme na področju oskrbe s plinastimi gorivi. Določa tudi preskusne parametre za preskusne metode iz tega standarda. V povezavi z deli 1, 2 ,4 in 5 standarda EN 1555 se uporablja za fitinge iz polietilena, njihove spoje ter spoje s komponentami iz polietilena in drugih materialov, namenjene uporabi v naslednjih pogojih: a) najvišji obratovalni tlak obratovalni tlak MOP do vključno 10 bar); b) delovna temperatura 20 °C kot referenčna temperatura. Standard EN 1555 (vsi deli) zajema razpon najvišjih obratovalnih tlakov in določa zahteve glede barv in aditivov. Ta evropski standard se uporablja za naslednje vrste fitingov: c) elektrofuzijski vtični fitingi; d) elektrofuzijski fitingi s sedlom; e) fitingi s spojnimi zatiči (za spajanje koncev z uporabo segretih orodij in spajanje s pomočjo elektrofuzijskega vtiča); f) mehanični fitingi. Fitingi so lahko npr. v obliki spojnikov, enakih ali zmanjšanih priključkov T, regulatorjev, kolen ali kapic.

General Information

• Status: Withdrawn
• Publication Date: 06-Nov-2012
• Withdrawal Date: 06-Jul-2021
• ICS: 23.040.45 - Plastics fittings
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 12 - Systems for water supply and pressure drainage and sewerage - PE, PP (solid wall)
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 07-Jul-2021
• Ref Project: SIST EN 1555-3:2010+A1:2013 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings

Relations

• Merged From: EN 1555-3:2010 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
• Effective Date: 18-Jan-2023
• Merged From: EN 1555-3:2010/FprA1 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
• Effective Date: 15-Aug-2012
• Replaced By: EN 1555-3:2021 - Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
• Effective Date: 14-Jul-2021

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Polietilen (PE) - 3. del: FitingiKunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 3: FormstückeSystèmes de canalisations en plastique pour la distribution de combustibles gazeux - Polyéthylène (PE) - Partie 3 : RaccordsPlastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings91.140.40Sistemi za oskrbo s plinomGas supply systems83.140.30Cevi, fitingi in ventili iz polimernih materialovPlastics pipes, fittings and valvesICS:Ta slovenski standard je istoveten z:EN 1555-3:2010+A1:2012SIST EN 1555-3:2010+A1:2013en,fr,de01-februar-2013SIST EN 1555-3:2010+A1:2013SLOVENSKI
STANDARDSIST EN 1555-3:20101DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1555-3:2010+A1
November 2012 ICS 23.040.45 Supersedes EN 1555-3:2010English Version
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings
Systèmes de canalisations en plastique pour la distribution de combustibles gazeux - Polyéthylène (PE) - Partie 3 : Raccords
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 3: Formstücke This European Standard was approved by CEN on 30 July 2010 and includes Amendment 1 approved by CEN on 4 September 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1555-3:2010+A1:2012: ESIST EN 1555-3:2010+A1:2013

Examples of typical terminal connection for electrofusion fittings . 24Annex B (normative)
Short-term pressure test method . 26B.1 Principle. 26B.2 Apparatus . 26B.3 Test piece . 26B.4 Procedure . 26B.5 Test report . 27Annex C (normative)
Tensile test for fitting/pipe assemblies . 28C.1 Principle. 28C.2 Apparatus . 28C.3 Test piece . 28C.4 Procedure . 28C.5 Test report . 28Bibliography . 30 SIST EN 1555-3:2010+A1:2013

 EN 1555-2, Plastics piping systems for the supply of gaseous fuels  Polyethylene (PE)  Part 2: Pipes;  EN 1555-3, Plastics piping systems for the supply of gaseous fuels  Polyethylene (PE)  Part 3: Fittings (this standard);  prEN 1555-4, Plastics piping systems for the supply of gaseous fuels  Polyethylene (PE)  Part 4: Valves;  EN 1555-5, Plastics piping systems for the supply of gaseous fuels  Polyethylene (PE)  Part 5: Fitness for purpose of the system;  CEN/TS 1555-7, Plastics piping systems for the supply of gaseous fuels  Polyethylene (PE)  Part 7: Guidance for assessment of conformity. NOTE EN 12007-2:2000 [1] prepared by CEN/TC 234 “Gas infrastructure” deals with the recommended practice for installation of plastics pipes system in accordance with EN 1555 (all parts). System Standards are based on the results of the work being undertaken in ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids", which is a Technical Committee of the International Organization for Standardization (ISO). Th
...