iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 17778:2015

(Main)

Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)

Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)

ISO 17778:2015 specifies a method for determining the flow rate/pressure drop relationship of components for plastics piping systems when tested using air at 25 mbar.

Kunststoff-Rohrleitungssysteme - Formstücke, Armaturen und Zubehörteile - Bestimmung des Zusammenhanges zwischen Gasdurchfluss und Druckabfall (ISO 17778:2015)

Diese Norm legt ein Verfahren für die Bestimmung des Zusammenhanges zwischen Gasdurchflussmenge und Druckabfall der Komponenten für Kunststoffrohrleitungssysteme fest, wenn diese mit Luft bei 25 mbar geprüft werden.
ANMERKUNG   1 bar = 105 N/m².

Systèmes de canalisations en plastiques - Raccords, robinets et équipements auxiliaires - Détermination du rapport débit gazeux/perte de charge (ISO 17778:2015)

L'ISO 17778:2015 spécifie une méthode pour la détermination du rapport débit gazeux/perte de charge des composants de systèmes de canalisations en plastiques, les essais ayant lieu avec de l'air à 25 mbar.

Cevni sistemi iz polimernih materialov - Fitingi, ventili in pribor - Določanje razmerja plinskega pretoka/padca tlaka (ISO 17778:2015)

General Information

Status
Published
Publication Date
24-Mar-2015
Withdrawal Date
29-Sep-2015
ICS
23.040.20 - Plastics pipes
23.040.45 - Plastics fittings
23.060.01 - Valves in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 32 - Valves
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
25-Mar-2015
Completion Date
25-Mar-2015
Ref Project
SIST EN ISO 17778:2015 - Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships (ISO 17778:2015)

Relations

Replaces
EN 12117:1997 - Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
Effective Date
01-Apr-2015

Buy Standard

EN ISO 17778:2015EN ISO 17778:2015
PreviousNext
Standard
EN ISO 17778:2015
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2015
1DGRPHãþD
SIST EN 12117:1999
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY)LWLQJLYHQWLOLLQSULERU'RORþDQMH
UD]PHUMDSOLQVNHJDSUHWRNDSDGFDWODND ,62
Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow
rate/pressure drop relationships (ISO 17778:2015)
Kunststoff-Rohrleitungssysteme - Formstücke, Armaturen und Zubehörteile -
Bestimmung des Zusammenhanges zwischen Gasdurchfluss und Druckabfall (ISO
17778:2015)
Systèmes de canalisations en plastiques - Raccords, robinets et équipements auxiliaires
- Détermination du rapport débit gazeux/perte de charge (ISO 17778:2015)
Ta slovenski standard je istoveten z: EN ISO 17778:2015
ICS:
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 17778
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 23.040.20; 23.040.45; 23.060.01 Supersedes EN 12117:1997
English Version
Plastics piping systems - Fittings, valves and ancillaries -
Determination of gaseous flow rate/pressure drop relationships
(ISO 17778:2015)
Systèmes de canalisations en plastiques - Raccords, Kunststoff-Rohrleitungssysteme - Formstücke, Armaturen
robinets et équipements auxiliaires - Détermination du und Zubehörteile - Bestimmung des Zusammenhanges
rapport débit gazeux/perte de charge (ISO 17778:2015) zwischen Gasdurchfluss und Druckabfall (ISO 17778:2015)
This European Standard was approved by CEN on 14 November 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17778:2015 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 17778:2015) has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12117:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17778:2015 has been approved by CEN as EN ISO 17778:2015 without any modification.
INTERNATIONAL ISO
STANDARD 17778
First edition
2015-03-15
Plastics piping systems —
Fittings, valves and ancillaries —
Determination of gaseous flow rate/
pressure drop relationships
Systèmes de canalisations en plastiques — Raccords, robinets et
équipements auxiliaires — Détermination du rapport débit gazeux/
perte de charge
Reference number
ISO 17778:2015(E)
©
ISO 2015
ISO 17778:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

ISO 17778:2015(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Test pieces preparation . 3
6 Procedure. 3
7 Calculation of results . 4
8 Test report . 4
ISO 17778:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was dra
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 1452-4:2009(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
SIST EN ISO 1452-4:2010

ISO 1452-4:2009 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC‑U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to.
In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC‑U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following:
- water mains and services buried in ground;
- conveyance of water above ground for both outside and inside buildings;
- buried and above-ground drainage and sewerage under pressure.
It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. It is also applicable to valves for the conveyance of water and waste water up to and including 45 °C.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2588:2024(Main)
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
kSIST FprEN 2588:2024

This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
-   ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
-   synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 18075:2024(Main)
Resilient, textile, laminate and modular mechanical locked floor coverings - Circular economy and sustainability - Recommendations/guidelines for design
kSIST-TS FprCEN/TS 18075:2024

The aim of this document is to provide general recommendations and guidelines on how to design a product to optimize its reuse and recyclability at the end of its lifetime as well as to take into account sustainable sourcing of materials for all floor covering product groups covered by CEN/TC 134. The overall target is to avoid waste and pollution and to achieve a product fit for the circular economy.
In a linear economy, the focus of product design is on developing new products without considering the recycling or reuse of the raw materials used.
This document provides guidance for processes allowing for (raw) materials used to be returned to the economic cycle based on circular design principles. The focus is on open systems that allow for economically interesting alternatives and are not limited to the principle of closed cycles (product to product).
Specific attention is given to renewable materials, where applicable.
The document is structured along the life cycle of the products, starting with the production phase.
Excluded is packaging, which is not considered part of the product end-of-life stage.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-3:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 3: Tests for emissions of volatile organic substances (ISO 18562-3:2024)
kSIST FprEN ISO 18562-3:2024

This document specifies tests for the emissions of volatile organic substances from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify emissions of volatile organic substances that are added to the respirable gas stream by the materials of the gas pathway. This document establishes acceptance criteria for these tests.
NOTE            Gaseous emission of volatile organic substances includes emissions of volatile organic compounds, semi-volatile organic compounds and very volatile organic compounds.
This document addresses potential contamination of the gas stream arising from the gas pathways of medical devices or accessories, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the surfaces of gas pathways that are in direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories containing gas pathways that are addressed by this document include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 series.
This document is intended to be read in conjunction with ISO 18562-1.

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 899-2:2024(Main)
Plastics - Determination of creep behaviour - Part 2: Flexural creep by three-point loading (ISO 899-2:2024)
kSIST FprEN ISO 899-2:2024

This document specifies a method for determining the flexural creep of plastics in the form of standard test specimens under specified conditions such as those of pre-treatment, temperature and humidity. It is only applicable to a simple freely supported beam loaded at mid-span (three-point-loading test).
 The method is suitable for use with rigid and semi-rigid non-reinforced, filled and fibre-reinforced plastics materials (see ISO 472 for definitions) test specimens moulded directly or machined from sheets or moulded articles.
NOTE            The method can be unsuitable for certain fibre-reinforced materials due to differences in fibre orientation
The method is intended to provide data for engineering-design, quality control, research and development purposes.
The method might not be applicable for determining the flexural creep of rigid cellular plastics (attention is drawn in this respect to ISO 1209-1 and ISO 1209-2).

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18562-2:2024(Main)
Biocompatibility evaluation of breathing gas pathways in healthcare applications - Part 2: Tests for emissions of particulate matter (ISO 18562-2:2024)
kSIST FprEN ISO 18562-2:2024

This document specifies tests for the emissions of particulate matter from the gas pathways of a medical device, its parts or accessories, which are intended to provide respiratory care or supply substances via the respiratory tract to a patient in all environments. The tests of this document are intended to quantify particles from 0,25 µm diameter to 10 µm diameter that are emitted by the medical device, its parts or accessories into the respirable gas stream. This document establishes acceptance criteria for these tests.
This document does not address nanoparticles. Insufficient data exist to establish exposure limits for particles less than 0,25 µm diameter.
This document does not address particles larger than 10 µm diameter. These particles are deposited in the nasal cavity. Additional information can be needed for medical devices or accessories that bypass the nose. This is outside the scope of this document but can be required by some authorities having jurisdiction.
This document therefore adopts the same approach as the US Environmental Protection Agency (EPA) in setting limits based solely on particle size and not their chemistry.
This document addresses potential contamination of the gas stream arising from the gas pathways, which is then conducted to the patient.
This document applies over the expected lifetime of the medical device in normal use and takes into account the effects of any intended processing.
This document does not address biological evaluation of the particles that are deliberately released by a nebulizer (i.e. the therapeutic agent).
This document does not address biological evaluation of the surfaces of gas pathways that have direct contact with the patient. The requirements for direct contact surfaces are found in the ISO 10993 series.
Medical devices, parts or accessories, containing gas pathways that are addressed by this document, include, but are not limited to, ventilators, anaesthesia workstations (including gas mixers), breathing systems, oxygen conserving devices, oxygen concentrators, nebulizers, low-pressure hose assemblies, humidifiers, heat and moisture exchangers, respiratory gas monitors, respiration monitors, masks, medical respiratory personal protective equipment, mouth pieces, resuscitators, breathing tubes, breathing systems filters, Y-pieces, and any breathing accessories intended to be used with such devices. The enclosed chamber of an incubator, including the mattress, and the inner surface of an oxygen hood are considered to be gas pathways and are also addressed by this document.
This document does not address contamination already present in the gas supplied from the gas sources while medical devices are in normal use.
EXAMPLE            Contamination arriving at the medical device from gas sources such as medical gas pipeline systems (including the non-return valves in the pipeline outlets), outlets of pressure regulators connected or integral to a medical gas cylinder or room air taken into the medical device is not addressed by ISO 18562 (all parts).

  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13997:2024(Main)
Protective clothing - Mechanical properties - Determination of resistance to cutting by sharp objects (ISO 13997:2024)
oSIST prEN ISO 13997:2024

This document specifies a tomodynamometer cut test method and related calculations, for use on materials and assemblies designed for protective clothing, including gloves. The test determines resistance to cutting by sharp edges, such as knives, sheet metal parts, swarf, glass, bladed tools and castings.
When this document is cited as a test method in a material or product requirement standard, that standard contains the necessary information to permit the application of this document to the particular product.
This test does not provide data on the resistance to penetration by pointed objects such as needles and thorns, or the point of sharp-edged blades. The test described in this document is not considered suitable for testing materials made from chain mail and metal plates. The text of this document does not include provisions for the safeguard of the operator.

  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17984-1:2024(Main)
Assistance dogs - Part 1: Vocabulary
SIST EN 17984-1:2024

This document specifies the terms and definitions that apply to:
—   different types of assistance dogs;
—   the beneficiary and client services;
—   health and disabilities;
—   assistance dog service providers;
—   assistance dog training staff and related professionals;
—   the socialization and training processes;
—   conformity assessment, identification and registration;
—   accessibility.

  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16709:2024(Main)
Automotive fuels - High FAME diesel fuel (B20 and B30) - Requirements and test methods
kSIST FprEN 16709:2024

This document specifies requirements and test methods for marketed and delivered high FAME (B20 and B30) diesel fuel for use in diesel engine vehicles designed or subsequently adapted to run on such fuel. High FAME diesel fuel is a mixture of up to 20 % (V/V) in total and up to 30 % (V/V) in total respectively fatty acid methyl esters (commonly known as FAME) complying with EN 14214 and automotive diesel fuel complying with EN 590.
For maintenance and control reasons high FAME (B20 and B30) diesel fuel is to be used in captive fleets that are intended to have an appropriate fuel management (see Clause 4).
NOTE 1   These products are allowed in Europe [4], but national legislation can set additional requirements or rules concerning, or even prohibiting, marketing or delivering of the product.
NOTE 2   For the purposes of this document, the terms “% (m/m)” and “% (V/V)” are used to represent respectively the mass fraction and the volume fraction.
NOTE 3   In this document, A-deviations apply (see Annex A).

  • Draft
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day