EN ISO 20848-2:2008
(Main)Packaging - Plastics drums - Part 2: Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l (ISO 20848-2:2006)
Packaging - Plastics drums - Part 2: Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l (ISO 20848-2:2006)
ISO 20848-2:2006 specifies the characteristics and dimensions of non-removable head (tight head) plastics drums with a nominal capacity of 208,2 l and 220 l.
Verpackung - Kunststofffässer - Teil 2: Spundfässer mit einem Nennvolumen von 208,2 l und 220 l (ISO 20848-2:2006)
Dieser Teil von ISO 20848 legt die Eigenschaften und Maße von Spundfässern aus Kunststoff mit einem
Nennvolumen von 208,2 l und 220 l fest.
Emballages - Fûts en matière plastique - Partie 2: Fûts à ouverture non amovible (ouverture partielle) d'une capacité nominale de 208,2 l et 220 l (ISO 20848-2:2006)
L'ISO 20848-2:2006 spécifie les caractéristiques et dimensions des fûts à ouverture non amovible (ouverture partielle) d'une capacité nominale de 208,2 l et 220 l.
Embalaža - Plastični sodi - 2. del: Sodi z nesnemljivim pokrovom (ozka odprtina) z nazivno prostornino 208,2 l in 220 l (ISO 20848-2:2006)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2008
(PEDODåD3ODVWLþQLVRGLGHO 6RGL]QHVQHPOMLYLPSRNURYRP R]NDRGSUWLQD ]
QD]LYQRSURVWRUQLQROLQO ,62
Packaging - Plastics drums - Part 2: Non-removable head (tight head) drums with a
nominal capacity of 208,2 l and 220 l (ISO 20848-2:2006)
Verpackung - Kunststofffässer - Teil 2: Spundfässer mit einem Nennvolumen von 208,2 l
und 220 l (ISO 20848-2:2006)
Emballages - Futs en matiere plastique - Partie 2: Futs a ouverture non amovible
(ouverture partielle) d'une capacité nominale de 208,2 l et 220 l (ISO 20848-2:2006)
Ta slovenski standard je istoveten z: EN ISO 20848-2:2008
ICS:
55.140 6RGL.RYLQVNLVRGL5RþNH Barrels. Drums. Canisters
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 20848-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 55.140
English Version
Packaging - Plastics drums - Part 2: Non-removable head (tight
head) drums with a nominal capacity of 208,2 l and 220 l (ISO
20848-2:2006)
Emballages - Fûts en matière plastique - Partie 2: Fûts à Verpackung - Kunststofffässer - Teil 2: Spundfässer mit
ouverture non amovible (ouverture partielle) d'une capacité einem Nennvolumen von 208,2 l und 220 l (ISO 20848-
nominale de 208,2 l et 220 l (ISO 20848-2:2006) 2:2006)
This European Standard was approved by CEN on 16 May 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20848-2:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
The text of ISO 20848-2:2006 has been prepared by Technical Committee ISO/TC 122 “Packaging” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 20848-2:2008 by
Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn
at the latest by December 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 20848-2:2006 has been approved by CEN as a EN ISO 20848-2:2008 without any
modification.
INTERNATIONAL ISO
STANDARD 20848-2
First edition
2006-09-15
Packaging — Plastics drums —
Part 2:
Non-removable head (tight head)
drums with a nominal capacity
of 208,2 l and 220 l
Emballages — Fûts en matière plastique —
Partie 2: Fûts à ouverture non amovible (ouverture partielle)
d'une capacité nominale de 208,2 l et 220 l
Reference number
ISO 20848-2:2006(E)
©
ISO 2006
ISO 20848-2:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 20848-2:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Requirements . 2
4.1 Dimensions. 2
4.2 Drum mass . 3
4.3 Material identification symbol . 3
4.4 Closures. 4
4.5 Materials . 4
4.6 Handling. 4
4.7 Stacking . 4
4.8 Draining . 5
4.9 Finish. 5
5 Designation . 5
Annex A (normative) Capacity measurement method for non-removable head (tight head)
plastics drums. 6
Annex B (normative) Draining test method for non-removable head (tight head) plastics drums . 8
Annex C (normative) International material code symbols . 10
Bibliography . 12
ISO 20848-2:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20848-2 was prepared by Technical Committee ISO/TC 122, Packaging.
ISO 20848 consists of the following parts, under the general title Packaging — Plastics drums:
⎯ Part 1: Removable head (open head) drums with a nominal capacity of 113,6 l to 220 l
⎯ Part 2: Non-removable head (tight head) drums with a nominal capacity of 208,2 l and 220 l
⎯ Part 3: Plug/bung closure systems for plastics drums with a nominal capacity of 113,6 l to 220 l
iv © ISO 2006 – All rights reserved
ISO 20848-2:2006(E)
Introduction
Throughout the world, a large number of plastics drum types with different dimensions and characteristics are
being used. The differences in location of the minimum filling opening and outer dimensions result in
differences in filling, handling and transportation.
ISO 20848 specifies the characteristics and dimensions of plastics drums which are of importance for the
worldwide safe handling and transport of substances and for the continued reuse of the drums during their life
cycle. Detailed performance requirements and the related test methods are not included as they depend upon
the specific application.
Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the
regulatory requirements which govern the transport of those goods in the countries concerned, including
capseals/overseals fitted in accordance with the certificate. Depending upon the mode of transport, this
means meeting the requirements of:
⎯ UN (United Nations) — Recommendations on the Transport of Dangerous Goods,
⎯ ICAO (International Civil Aviation Organization) — Technical Instructions for the Safe Transport of
Dangerous Goods by Air,
⎯ IMO (International Maritime Organization) — International Maritime Dangerous Goods (IMDG) Code.
This involves the certification and marking of the drums according to the regulations.
INTERNATIONAL STANDARD ISO 20848-2:2006(E)
Packaging — Plastics drums —
Part 2:
Non-removable head (tight head) drums with a nominal capacity
of 208,2 l and 220 l
1 Scope
This part of ISO 20848 specifies the characteristics and dimensions of non-removable head (tight head)
plastics drums with a nominal capacity of 208,2 l and 220 l.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 20848-3, Packaging — Plastics drums — Part 3: Plug/bung closure systems for plastics drums with a
nominal capacity of 113,6 l to 220 l
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
non-removable head (tight head) drum
TH
flat-ended or convex-ended circular cross-section packaging with openings for filling and emptying in the head
not exceeding 70 mm in diameter
3.2
nominal capacity
NC
capacity in litres which, by convention, is used to represent a class of drums of similar brimful capacities
3.3
brimful capacity
BC
volume of water in l
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.