iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14382:2005+A1:2009/AC:2009

(Corrigendum)

Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

TC - Addition of a footnote to text to Clause 1, last indent and change of sub-clause headings/numbering in 4.3, including update of concerned cross references; correction of class values in the inspection document

Sicherheitseinrichtungen für Gas-Druckregelanlagen und –einrichtungen - Gas-Sicherheitsabsperreinrichtungen für Eingangsdrücke bis 100 bar

Dispositifs de sécurité pour postes et installations de détente-régulation de pression de gaz - Clapets de sécurité pour pressions amont jusqu'à 100 bar

Varnostne naprave za plinske regulacijske postaje in napeljave - Plinske varnostne zaporne naprave za vstopne tlake do 100 bar - Popravek AC

General Information

Status
Withdrawn
Publication Date
09-Jun-2009
Withdrawal Date
20-Aug-2019
ICS
23.060.40 - Pressure regulators
Technical Committee
CEN/TC 235 - Gas pressure regulators and associated safety devices for use in gas transmission and distribution
Drafting Committee
CEN/TC 235/WG 1 - Safety shut-off devices, safety relief devices and small regulators with or without safety devices used in gas transmission and/or distribution.
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
21-Aug-2019
Directive
2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 14382:2005+A1:2009/AC:2009 - Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar

Relations

Replaced By
EN 14382:2019 - Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
Effective Date
28-Aug-2019
Corrects
EN 14382:2005+A1:2009 - Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
Effective Date
08-Jun-2022

Buy Standard

EN 14382:2005+A1:2009/AC:2009EN 14382:2005+A1:2009/AC:2009
PreviousNext
Corrigendum
EN 14382:2005+A1:2009/AC:2009
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varnostne naprave za plinske regulacijske postaje in napeljave - Plinske varnostne zaporne naprave za vstopne tlake do 100 bar - Popravek ACSicherheitseinrichtungen für Gas-Druckregelanlagen und –einrichtungen - Gas-Sicherheitsabsperreinrichtungen für Eingangsdrücke bis 100 barDispositifs de sécurité pour postes et installations de détente-régulation de pression de gaz - Clapets de sécurité pour pressions amont jusqu'à 100 barSafety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar23.060.40Pressure regulatorsICS:Ta slovenski standard je istoveten z:EN 14382:2005+A1:2009/AC:2009SIST EN 14382:2005+A1:2009/AC:2009en01-julij-2009SIST EN 14382:2005+A1:2009/AC:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN14382:2005+A1:2009/ACJune 2009Juin 2009Juni 2009ICS 23.060.40English versionVersion FrançaiseDeutsche FassungSafety devices for gas pressure regulating stations and installations - Gassafety shut-off devices for inlet pressures up to 100 barDispositifs de sécurité pour postes etinstallations de détente-régulation depression de gaz - Clapets de sécurité pourpressions amont jusqu'à 100 barSicherheitseinrichtungen für Gas-Druckregelanlagen und -einrichtungen -Gas-Sicherheitsabsperreinrichtungen fürEingangsdrücke bis 100 barThis corrigendum becomes effective on 10 June 2009 for incorporation in the three official languageversions of the EN.Ce corrigendum prendra effet le 10 juin 2009 pour incorporation dans les trois versions linguistiquesofficielles de la EN.Die Berichtigung tritt am 10.Juni 2009 zur Einarbeitung in die drei offiziellen Sprachfassungen der ENin Kraft.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier auxmembres nationaux du CEN.Alle Rechte d
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 334:2019/FprA1(Amendment)
Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
SIST EN 334:2019/kFprA1:2024

This European Standard specifies constructional, functional, testing, marking, sizing and documentation requirements of gas pressure regulators:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from - 20  °C to +60 °C,
which operate with fuel gases of the 1st and 2nd  family as defined in EN 437:2003+A1:2009, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas pressure regulators" hereafter will be called "regulators" except in the titles.
For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, the Annex ZA lists all applicable essential safety requirements of the European legislation on pressure equipment except external and internal corrosion resistance for applications in corrosive environment.
This document considers the following temperature classes/types of regulators:
-   temperature class 1: operating temperature range from −10 °C to 60 °C;
-   temperature class 2: operating temperature range from −20 °C to 60 °C;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source.
The regulator may incorporate a second regulator, used as monitor, complying with the requirements in this document.
The regulator may incorporate a safety shut off device (SSD) complying with the requirements of EN 14382.
The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex E and/or a vent limiter, complying with the requirements in Annex I.
This document does not apply to:
-   regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   regulators designed to be incorporated into pressure control systems used in service lines ) with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar;
-   regulators for which a specific document exists (e.g. EN 88-1 and EN 88-2, etc.);
-   industrial process control valves in accordance with EN 1349.
The normative Annex G of this document lists some suitable materials for pressure bearing parts, inner metallic partition walls, auxiliary devices, integral process and sensing lines, connectors and fasteners. Other materials may be used when complying with the restrictions given in Table 5.
Continued integrity of gas pressure regulators is ensured by suitable surveillance checks and maintenance. For periodic functional checks and maintenance it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document has introduced the reaction of the pressure regulators to the specified reasonable expected failures in terms of "fail close" and "fail open" pressure regulator types, but it should be considered that there are other types of failures whose consequences can bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards will be reduced by a suitable surveillance in use / maintenance.
In this document, both pressure regulators that can be classified as "safety accessories" by themselves (monitors) according to European legislation on pressure equipment as well as regulators that can be used to provide the necessary pressure protection through redundancy (e.g. pressure regulator with integrated safety shut-off device, pressure regulator + in-line monitor, pressure regulator + safety shut off device) are considered.
The provisions in this document are in line with the state of art at the moment of writing.

  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14382:2019/FprA1(Amendment)
Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
SIST EN 14382:2019/kFprA1:2023

This document specifies constructional, functional, testing marking and sizing requirements and documentation of gas safety shut-off devices:
-   for inlet pressures up to 100 bar and nominal diameters up to DN 400;
-   for an operating temperature range from -20 °C to +60 °C;
which operate with fuel gases of the 1st and 2nd family as defined in EN 437, used in the pressure regulating stations in accordance with EN 12186 or EN 12279, in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Safety Requirements of Directive 2014/68/EU (PED).
This document considers the following temperature classes/types of SSDs:
-   temperature class 1: operating temperature range from -10 °C to 60 °C;
-   temperature class 2: operating temperature range from -20 °C to 60 °C;
-   functional class A: SSDs that close when damage to the pressure detecting element occurs or when external power fails and whose re-opening, is possible only manually;
-   functional class B: SSDs that do not close when damage to the pressure detecting element occurs but provide suitable and reliable protection and whose re-opening, is possible only manually;
-   type IS: (integral strength type);
-   type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as "in conformity with EN 14382" and bear the mark "EN 14382".
The material and functional requirements specified in this document may be applied to SSDs which use thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
The SSD may incorporate a vent limiter, complying with the requirements in Annex J.
This standard for some paragraphs and sub clauses makes full reference to prEN 334:2016.
This document does not apply to:
-   SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters;
-   SSDs designed to be incorporated into pressure-regulating devices used in service lines  with volumetric flow rate ≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
Continued integrity of safety shut-off devices is ensured by periodic functional checks. For periodic functional checks it is common to refer to national regulations/standards where existing or users/manufacturers practices.
This document considers the reaction of the SSDs functional class A to the specified reasonable expected failures in terms of "fail close" behaviour, but it should be consider that there are other types of failures whose consequences cannot bring to the same reactions (these risks are covered via redundancy as per EN 12186) and that residual hazards should be reduced by a suitable surveillance in use / maintenance.
In this document, both safety shut-off devices that can be classified as "safety accessories" by themselves according the Pressure Equipment Directive (2014/68/EU) as well as safety shut-off devices that can be used to provide the necessary pressure protection through redundancy (e.g. shutoff device integrated in a pressure regulator, shut-off device with a second shut-off device) are considered. Addition of environmental considerations;
The provisions in this document are in line with the state of art at the moment of writing.
This document does not intend to limit the improvement of actual provisions (materials, requirements, test methods, acceptance criteria, etc.) or the developing of new provisions for SSDs where they are suitable to ensure an equivalent level of reliability.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14382:2005/prA1(Amendment)
Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
SIST EN 14382:2005/kprA1:2008

Tolerance of 9 months before UAP per CEN/TC 235 res. C03/2006.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 334:2005/prA1(Amendment)
Gas pressure regulators for inlet pressures up to 100 bar
SIST EN 334:2005/kprA1:2008

Tolerance of 9 months requested before UAP per CEN/TC 235 C02/2006.

  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17871:2020/A1:2024(Amendment)
Gas cylinders - Quick-release cylinder valves - Specification and type testing - Amendment 1 (ISO 17871:2020/Amd 1:2024)
SIST EN ISO 17871:2020/A1:2024

No scope available

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10297:2024(Main)
Gas cylinders - Cylinder valves - Specification and type testing (ISO 10297:2024, Corrected version 2024-05)
SIST EN ISO 10297:2024

This document specifies design, type testing and marking requirements for:
a)       cylinder valves intended to be fitted to refillable transportable gas cylinders;
b)       main valves (excluding ball valves) for bundles of cylinders;
c)        cylinder valves or main valves with integrated pressure regulator (VIPR);
NOTE 1        This includes the following specific VIPR designs where:
1)  The pressure regulating system is acting as the primary valve operating mechanism (VIPR type B). This also includes designs where closure of the primary valve operating mechanism is obtained by closing the seat of the pressure regulating mechanism.
2)  The primary valve operating mechanism is located at the low-pressure side of the pressure regulating system (VIPR type C).
d)       valves for pressure drums and tubes;
which convey compressed, liquefied or dissolved gases.
NOTE 2        Where there is no risk of ambiguity, cylinder valves, main valves, VIPRs and valves for pressure drums and tubes are addressed with the collective term “valves” within this document.
This document does not apply to
—     valves for cryogenic equipment, portable fire extinguishers and liquefied petroleum gas (LPG);
—     quick-release cylinder valves (e.g. for fire-extinguishing, explosion protection and rescue applications) - requirements for quick-release cylinder valves are specified in ISO 17871 which contains normative references to this document;
—     self-closing cylinder valves and ball valves.
NOTE 3        Requirements for valves for cryogenic vessels are specified in ISO 21011 and at a regional level, e.g. in EN 1626. Requirements for LPG valves are specified in ISO 14245 or ISO 15995. Requirements for self-closing cylinder valves are specified in ISO 17879. Requirements for ball valves are specified in ISO 23826. Requirements for valves for portable fire extinguishers at a regional level are specified, for example, in the EN 3 series.
This document only covers the function of a valve as a closure. Other functions that are possibly integrated in the valve can be covered by other standards. Such standards do however not constitute requirements according to this document.
NOTE 4        Definition of and specific requirements for VIPRs in addition to those that are given in this document are specified in ISO 22435 for industrial applications or ISO 10524-3 for medical applications. Similarly, certain specific requirements for residual pressure valves (RPV) with or without a non-return function in addition to those that are given in this document are given in ISO 15996.
NOTE 5        Certain specific requirements for valves for breathing apparatus in addition to those that are given in this document are specified at a regional level, for example, in the EN 144 series. Certain specific requirements for quick-release valves for fixed fire-fighting systems in addition to those that are given in this document are specified in ISO 16003 and at a regional level, for example, in EN 12094–4.
NOTE 6        Requirements for manufacturing tests and examinations of valves covered by this document are given in ISO 14246.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
SIST EN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 88-1:2022+A1:2023(Main + Amendment)
Safety and control devices for gas burners and gas burning appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa
SIST EN 88-1:2022+A1:2024

EN 13611:2019, Clause 1 applies with the following modification and addition:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for
pressure regulators and pneumatic gas/air ratio pressure regulators (zero pressure regulators are
included as a special type of pneumatic gas/air ratio pressure regulators) for burners and appliances
burning one or more gaseous fuels, hereafter referred to as “pressure regulators”.
This document is applicable to pressure regulators with declared maximum inlet pressures up to and
including 50 kPa and of nominal connection sizes up to and including DN 250.
Addition:
This document is applicable to:
— pressure regulators which use auxiliary energy;
— pneumatic gas/air ratio pressure regulators, which function by controlling a gas outlet pressure in
response to an air signal pressure, air signal differential pressure, and/or to a furnace pressure signal
(zero pressure regulators are included as a special type of pneumatic gas/air ratio pressure
regulators);
— pneumatic gas/air ratio pressure regulators, which change an air outlet pressure in response to a gas
signal pressure or a gas signal differential pressure.
This document is not applicable to:
— pressure regulators connected directly to a gas distribution network or to a container that maintains
a standard distribution pressure;
— pressure regulators intended for gas appliances to be installed in the open air and exposed to the
environment;
— mechanically linked gas/air ratio controls;
— electronic gas/air ratio controls (EN 12067-2:2022).
The 4th paragraph of EN 13611:2019, Clause 1 is removed.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1854:2022+A1:2023(Main + Amendment)
Safety and control devices for burners and appliances burning gaseous and/or liquid fuels - Pressure sensing devices for gas burners and gas burning appliances
SIST EN 1854:2023+A1:2024

EN 13611:2019, Clause 1 applies with the following modification:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing of pressure sensing devices for burners and appliances burning one or more gaseous fuels.
This document is applicable to pressure sensing devices for gaseous fuels, air, or combustion products with declared maximum inlet pressures up to and including 500 kPa.
It applies to all types of pressure sensing devices, including electronic, differential and inferential types.
It also specifies requirements for pressure sensing devices which are intended to be applied to steam boilers and as such need to meet increased reliability requirements.
EN 13611:2019 Clause 1, 4th paragraph is not applicable.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1106:2022+A1:2023(Main + Amendment)
Manually operated taps for gas burning appliances
SIST EN 1106:2022+A1:2024

EN 13611:2019, Clause 1 applies with the following modification and addition:
Modification:
The 1st paragraph of EN 13611:2019, Clause 1 is replaced by:
This document specifies the safety, design, construction, and performance requirements and testing for manually operated taps and presetting taps for burners and appliances burning one or more gaseous fuels, hereafter referred to as "taps".
This document is applicable to taps with declared maximum inlet pressures up to and including 50 kPa and of nominal connection sizes up to and including DN 50 for use with one or more fuel gases.
Addition:
This document is not applicable to:
a)   manual operated shut-off valves conforming to EN 331:2015;
b)   controls which use auxiliary energy (e.g. electrical energy supplied externally).
The 4th paragraph of EN 13611:2019, Clause 1 is removed.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day