Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO 19085-10:2018, Corrected version 2019-12)

ISO 19085-10:2018 gives the safety requirements and measures for displaceable building site saws, designed to cut wood and materials with similar physical characteristics to wood, hereinafter referred to as "machines".
NOTE 1    For the definition of displaceable machine, see ISO 19085‑1:2017, 3.5.
ISO 19085-10:2018 deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
NOTE 2    For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010.
The machine can also be fitted with a device for the saw blade to be manually raised and lowered through the table, whose hazards have been dealt with.
This document does not apply to the following:
a)    machines with a maximum saw blade diameter smaller than 350 mm or greater than 500 mm;
b)    hand-held woodworking machines, including any adaptation permitting their use in a different mode, i.e. bench mounting;
c)    machines with a device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table;
NOTE 3    Hand-held motor-operated electric tools are covered by IEC 62841‑1 together with IEC 62841‑2‑5.
NOTE 4    Machines with the device to tilt the saw blade for angle cutting, machines with more than one saw blade rotational speed and machines equipped with a sliding table are considered as table saws, covered by ISO 19085‑9.
ISO 19085-10:2018 is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication.

Holzbearbeitungsmaschinen - Sicherheit - Teil 10: Baustellenkreissägemaschinen (ISO 19085-10:2018, korrigierte Fassung 2019-12)

Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen für verschiebbare Baustellenkreissägemaschinen zur Verfügung, nachfolgend als „Maschinen“ bezeichnet, die zum Schneiden von Holz und Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz konstruiert sind.
ANMERKUNG 1   Hinsichtlich der Definition von verschiebbaren Maschinen siehe ISO 19085-1:2017, 3.5.
Er behandelt alle im Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf die Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet, eingestellt und gewartet werden, einschließlich der vernünftigerweise vorhersehbaren Fehlanwendung. Ferner wurden Transport, Zusammenbau, Demontage, Rückbau und Verschrottung berücksichtigt.
ANMERKUNG 2   Hinsichtlich zutreffender aber nicht signifikanter Gefährdungen, z. B. scharfe Kanten des Maschinengestells, siehe ISO 12100:2010.
Die Maschine kann auch mit einer handbetätigten Einrichtung zum Anheben und Absenken des Sägeblatts durch den Tisch, deren Gefährdungen berücksichtigt wurden, ausgerüstet sein.
Dieses Dokument gilt nicht für:
a)   Maschinen mit einem größten Sägeblattdurchmesser von weniger als 350 mm oder mehr als 500 mm;
b)   handgeführte Holzbearbeitungsmaschinen einschließlich irgendwelcher Einrichtungen, die ihre Verwendung in einer anderen Weise, d. h. in einem Gestell montiert, ermöglichen;
c)   Maschinen mit einer Einrichtung zum Schrägstellen des Sägeblattes für Winkelschnitte, Maschinen mit mehr als einer Sägeblattdrehzahl und Maschinen, die mit einem Schiebetisch ausgerüstet sind;
ANMERKUNG 3   Handgeführte motorbetriebene Elektrowerkzeuge sind in IEC 62841-1 zusammen mit IEC 64821-2-5 erfasst.
ANMERKUNG 4   Maschinen mit einer Einrichtung zum Schrägstellen des Sägeblattes für Winkelschnitte, Maschinen mit mehr als einer Sägeblattdrehzahl und Maschinen, die mit einem Schiebetisch ausgerüstet sind, werden als Tischkreissägemaschinen betrachtet, die in ISO 19085-9 behandelt werden.
Dieses Dokument gilt nicht für Maschinen, die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind, oder Maschinen, die vor seinem Ausgabedatum hergestellt wurden.

Machines à bois - Sécurité - Partie 10: Scies de chantier (ISO 19085-10:2018, Version corrigée 2019-12)

L'ISO 19085-10:2018 donne les exigences et les mesures de sécurité pour les scies de chantier transportables, conçues pour la coupe de bois et de matériau ayant des caractéristiques physiques similaires à celles du bois, ci-après désignées «machines».
NOTE 1    Pour la définition de machine transportable, voir l'ISO 19085‑1:2017, 3.5.
L'ISO 19085-10:2018 traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu'énumérés à l'Article 4, applicables aux machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut ont également été prises en compte.
NOTE 2    Pour les phénomènes dangereux pertinents mais non significatifs, par exemple, les arêtes vives du bâti de la machine, voir l'ISO 12100:2010.
La machine peut également être munie d'un dispositif pour élever et abaisser manuellement la lame de scie à travers la table, dont les phénomènes dangereux ont été traités.
L'ISO 19085-10:2018 ne s'applique pas à ce qui suit:
a)    aux machines avec un diamètre maximal de lame de scie inférieur à 350 mm ou supérieur à 500 mm;
b)    aux machines à bois portatives, y compris toute adaptation permettant leur utilisation de manière différente, c'est-à-dire fixées sur un bâti;
c)    aux machines équipées d'un dispositif d'inclinaison de la lame de scie pour réaliser une coupe oblique, aux machines ayant plusieurs vitesses de rotation de la lame de scie et aux machines équipées d'une table mobile;
NOTE 3    Les outils électroportatifs à moteur  sont couverts par l'IEC 62841‑1 conjointement à l'IEC 62841‑2‑5.
NOTE 4    Les machines équipées d'un dispositif d'inclinaison de la lame de scie pour réaliser une coupe oblique, les machines ayant plusieurs vitesses de rotation de la lame de scie et les machines équipées d'une table mobile sont considérées comme des scies à tables couvertes par l'ISO 19085‑9.
L'ISO 19085-10:2018 n'est pas applicable aux machines prévues pour une utilisation en atmosphères explosibles, ni aux machines fabriquées avant sa date de publication.

Lesnoobdelovalni stroji - Varnost - 10. del: Žage, ki se uporabljajo na gradbišču (ISO 19085-10:2018, popravljena verzija 2019-12)

Ta mednarodni standard obravnava vsa večja tveganja, nevarne razmere in dogodke iz točke 4 v zvezi s premestljivimi žagami, ki se uporabljajo na gradbišču (v nadaljevanju »stroji«) ter so namenjene rezanju masivnega lesa in materialov, ki imajo podobne lastnosti kot les (glej standard ISO 19085-1:2016), kadar se upravljajo, prilagajajo in vzdržujejo skladno z njihovim namenom in pod pogoji, ki jih je določil proizvajalec, vključno z razumno predvidljivo nepravilno uporabo. Upoštevane so tudi faze transporta, sestavljanja, razstavljanja in razrezovanja stroja.

General Information

Status
Withdrawn
Publication Date
29-Sep-2019
Withdrawal Date
30-Dec-2019
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
05-Jun-2019
Completion Date
05-Jun-2019

Relations

Buy Standard

Standard
EN ISO 19085-10:2019
English language
47 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
EN ISO 19085-10:2019
English language
47 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19085-10:2019
01-december-2019
Nadomešča:
SIST EN 1870-19:2014

Lesnoobdelovalni stroji - Varnost - 10. del: Žage, ki se uporabljajo na gradbišču

(ISO 19085-10:2018, popravljena verzija 2019-12)

Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO

19085-10:2018, Corrected version 2019-12)

Holzbearbeitungsmaschinen - Sicherheit - Teil 10: Baustellenkreissägemaschinen (ISO

19085-10:2018, korrigierte Fassung 2019-12)

Machines à bois - Sécurité - Partie 10: Scies de chantier (ISO 19085-10:2018, Version

corrigée 2019-12)
Ta slovenski standard je istoveten z: EN ISO 19085-10:2019
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN ISO 19085-10:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19085-10:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 13.110; 79.120.10 Supersedes EN 1870-19:2013
English Version
Woodworking machines - Safety - Part 10: Building site
saws (contractor saws) (ISO 19085-10:2018, Corrected
version 2019-12)

Machines à bois - Sécurité - Partie 10: Scies de chantier Holzbearbeitungsmaschinen - Sicherheit - Teil 10:

(ISO 19085-10:2018, Version corrigée 2019-12) Baustellenkreissägemaschinen (ISO 19085-10:2018,

korrigierte Fassung 2019-12)
This European Standard was approved by CEN on 16 October 2017.

This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 29 January 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-10:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Annex ZA (informative) Relationship between this European Standard and the essential

requirements of EU Directive 2006/42/EC/ aimed to be covered ................................................ 4

---------------------- Page: 4 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
European foreword

This document (EN ISO 19085-10:2019) has been prepared by Technical Committee ISO/TC 39

"Machine tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines -

Safety” the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by December 2019, and conflicting national standards

shall be withdrawn at the latest by December 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 1870-19:2013.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association, and supports essential requirements of EU Directive(s).

For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this

document.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 19085-10:2018, Corrected version 2019-12 has been approved by CEN as

EN ISO 19085-10:2019 without any modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC/ aimed to be covered

This European Standard has been prepared under a Commission’s standardization request “M/396” to

provide one voluntary means of conforming to essential requirements of the new approach Machinery

Directive 2006/42.

Once this standard is cited in the Official Journal of the European Union under that Directive,

compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of

the scope of this standard, a presumption of conformity with the corresponding essential requirements

of that Directive, and associated EFTA regulations.

Table ZA.1 — Correspondence between this European Standard and Directive 2006/42/EC

Essential Requirements (ERs) of Directive Clause(s)/subclause(s) Remarks/Notes
2006/42/EC of this EN
1.1.2 Principles of safety integration
a) fitted for its function Clause 5, 6, 7, 8
b) eliminate or reduce the risks, give measures, inform Clause 5, 6, 7, 8
c) intended use and reasonably foreseeable misuse Clause 5, 6, 7, 8
d) constraints in use 7.5, 8.3
e) equipment 6.1
1.1.3 Materials and products 6.2
1.1.4 Lighting 8.3
1.1.5 Design of machinery to facilitate its handling 8.3
1.1.6 Ergonomics 7.5
1.1.7 Operating position 5.2
1.2.1 Safety and reliability of control systems 5.1, 5.8, 5.12, 7.11
1.2.2 Control devices 5.2, 5.3, 5.4
1.2.3 Starting 5.3
1.2.4 Stopping 5.4, 5.5, 6.4
1.2.4.1 Normal stop 5.4.2
1.2.6 Failure of the power supply 5.8
1.2.8 Software 5.1
1.3.1 Risk of loss of stability 6.1, 8.3
1.3.2 Risk of break-up during operation 6.2, 8.3
1.3.3 Risks due to falling or ejected objects 6.2, 6.3, 6.5, 6.9, 8.3
---------------------- Page: 6 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
1.3.4 Risk due to surfaces, edges or angles
1.3.7 Risks related to moving parts 6.5, 6.6, 8.3
1.3.8 Choice of protection against risks related to moving 6.6, 8.3
parts
1.3.8.1 Moving transmission parts 6.6.3
1.3.8.2 Moving parts involved in the process 6.6.2
1.4.1 General requirements 6.9
1.4.2.1 Fixed guards 6.5.1
1.4.2.3 Adjustable guards restricting access 6.6.2
1.5.1 Electricity supply 7.13
1.5.2 Static electricity 7.11
1.5.4 Errors of fitting 7.12
1.5.6 Fire 7.1
1.5.8 Noise 7.2
1.5.11 External radiation 7.9
1.5.12 Laser equipment 7.10
1.5.13 Emission of hazardous materials and substances 7.3
1.6.1 Machinery maintenance 7.14, 8.3
1.6.2 Access to operating position and servicing points 7.14, 8.3
1.6.3 Isolation of energy sources 7.13, 8.3
1.6.4 Operator intervention 7.14, 8.3
1.6.5 Cleaning of internal parts 7.14, 8.3
1.7.1 Information and warnings on the machinery 7.10, 8.1, 8.2
1.7.2 Warning devices 7.10, 8.1
1.7.3 Marking of machinery 8.2
1.7.4 Instructions 7.10, 8.3
2.3 Machinery for working wood and analogous materials
a) guiding 6.10, 6.11
b) ejection 6.2, 6.3, 6.5, 6.6, 6.9, 8.3
c) brake 5.5, 6.4
d) accidental tool contact 6.6.2
---------------------- Page: 7 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European

Standard is maintained in the list published in the Official Journal of the European Union. Users of this

document should consult frequently the latest list published in the Official Journal of the European

Union.

WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of

this document.
---------------------- Page: 8 ----------------------
SIST EN ISO 19085-10:2019
INTERNATIONAL ISO
STANDARD 19085-10
First edition
2018-03
Corrected version
2019-12
Woodworking machines — Safety —
Part 10:
Building site saws (contractor saws)
Machines à bois — Sécurité —
Partie 10: Scies de chantier
Reference number
ISO 19085-10:2018(E)
ISO 2018
---------------------- Page: 9 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)
Contents Page

Foreword ..........................................................................................................................................................................................................................................v

Introduction ................................................................................................................................................................................................................................vi

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 2

4 List of significant hazards ........................................................................................................................................................................... 4

5 Safety requirements and measures for controls ................................................................................................................. 5

5.1 Safety and reliability of control systems ........................................................................................................................... 5

5.2 Control devices ....................................................................................................................................................................................... 5

5.3 Start .................................................................................................................................................................................................................. 6

5.4 Safe stops ..................................................................................................................................................................................................... 6

5.4.1 General...................................................................................................................................................................................... 6

5.4.2 Normal stop .......................................................................................................................................................................... 6

5.4.3 Operational stop ............................................................................................................................................................... 6

5.4.4 Emergency stop ................................................................................................................................................................ 6

5.5 Braking function of tool spindles ............................................................................................................................................ 6

5.6 Mode selection ........................................................................................................................................................................................ 6

5.7 Spindle speed changing ................................................................................................................................................................... 6

5.7.1 Spindle speed changing by changing belts on the pulleys ........................................................... 6

5.7.2 Spindle speed changing by incremental speed change motor ................................................. 6

5.7.3 Infinitely variable speed by frequency inverter .................................................................................... 6

5.8 Failure of any power supply ........................................................................................................................................................ 6

5.9 Manual reset control .......................................................................................................................................................................... 7

5.10 Enabling control ..................................................................................................................................................................................... 7

5.11 Machine moving parts speed monitoring ........................................................................................................................ 7

5.12 Time delay ................................................................................................................................................................................................... 7

6 Safety requirements and measures for protection against mechanical hazards ..............................7

6.1 Stability .......................................................................................................................................................................................................... 7

6.1.1 Stationary machines ..................................................................................................................................................... 7

6.1.2 Displaceable machines ............................................................................................................................................... 7

6.2 Risk of break-up during operation ......................................................................................................................................... 7

6.3 Tool holder and tool design.......................................................................................................................................................... 7

6.3.1 General...................................................................................................................................................................................... 7

6.3.2 Spindle locking .................................................................................................................................................................. 7

6.3.3 Circular saw blade fixing device ......................................................................................................................... 8

6.3.4 Flange dimensions for circular saw blades ............................................................................................... 8

6.4 Braking ........................................................................................................................................................................................................... 8

6.4.1 Braking of tool spindles ............................................................................................................................................. 8

6.4.2 Maximum run-down time ........................................................................................................................................ 8

6.4.3 Brake release ....................................................................................................................................................................... 8

6.5 Safeguards ................................................................................................................................................................................................... 8

6.5.1 Fixed guards ......................................................................................................................................................................... 8

6.5.2 Interlocking movable guards................................................................................................................................. 8

6.5.3 Hold-to-run control ....................................................................................................................................................... 8

6.5.4 Two hand control ............................................................................................................................................................ 8

6.5.5 Electro-sensitive protection equipment (ESPE) ................................................................................... 8

6.5.6 Pressure sensitive protection equipment (PSPE) ............................................................................... 8

6.6 Prevention of access to moving parts .................................................................................................................................. 9

6.6.1 General...................................................................................................................................................................................... 9

6.6.2 Guarding of tools .............................................................................................................................................................. 9

6.6.3 Guarding of drives .......................................................................................................................................................13

6.6.4 Guarding of shearing and/or crushing zones ......................................................................................13

© ISO 2018 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)

6.7 Impact hazard .......................................................................................................................................................................................13

6.8 Clamping devices ...............................................................................................................................................................................14

6.9 Measures against ejection ..........................................................................................................................................................14

6.9.1 General...................................................................................................................................................................................14

6.9.2 Guards material and characteristics ............................................................................................................14

6.9.3 Anti-kickback devices ...............................................................................................................................................14

6.10 Work-piece support and guides ............................................................................................................................................18

6.10.1 Rip fence ...............................................................................................................................................................................18

6.10.2 Cross-cut fence ...............................................................................................................................................................19

6.10.3 Machine table ...................................................................... .............................................................................................19

6.10.4 Extension table ...............................................................................................................................................................19

6.11 Safety appliances ................................................................................................................................................................................19

7 Safety requirements and measures for protection against other hazards ...........................................20

7.1 Fire ......... .........................................................................................................................................................................................................20

7.2 Noise .............................................................................................................................................................................................................21

7.2.1 Noise reduction at the design stage .............................................................................................................21

7.2.2 Noise emission measurement ...........................................................................................................................21

7.3 Emission of chips and dust ........................................................................................................................................................21

7.4 Electricity ..................................................................................................................................................................................................21

7.4.1 General...................................................................................................................................................................................21

7.4.2 Displaceable machines ............................................................................................................................................21

7.5 Ergonomics and handling ...........................................................................................................................................................21

7.6 Lighting .......................................................................................................................................................................................................21

7.7 Pneumatics ..............................................................................................................................................................................................21

7.8 Hydraulics ................................................................................................................................................................................................22

7.9 Electromagnetic compatibility ...............................................................................................................................................22

7.10 Laser ..............................................................................................................................................................................................................22

7.11 Static electricity ...................................................................................................................................................................................22

7.12 Errors of fitting ....................................................................................................................................................................................22

7.13 Isolation .....................................................................................................................................................................................................22

7.14 Maintenance ...........................................................................................................................................................................................22

8 Information for use .........................................................................................................................................................................................22

8.1 Warning devices ..................................................................................................................................................................................22

8.2 Markings ....................................................................................................................................................................................................22

8.2.1 General...................................................................................................................................................................................22

8.2.2 Additional markings ..................................................................................................................................................22

8.3 Instruction handbook ....................................................................................................................................................................23

8.3.1 General...................................................................................................................................................................................23

8.3.2 Additional information ............................................................................................................................................23

Annex A (informative) Performance level required ..........................................................................................................................24

Annex B (normative) Test for braking function .....................................................................................................................................25

Annex C (normative) Stability test for displaceable machines ..............................................................................................26

Annex D (normative) Impact test for guards ............................................................................................................................................27

Annex E (normative) Noise emission measurement for machines not in ISO 7960:1995 .........................28

Annex F (normative) Frame rigidity test .......................................................................................................................................................29

Annex G (normative) Saw blade guard rigidity test ...........................................................................................................................30

Annex H (normative) Minimum dimensions of machine table, extension table and table insert .....31

Annex I (normative) Riving knife longitudinal and lateral rigidity test .......................................................................32

Annex J (normative) Dimensions of test probe ......................................................................................................................................34

Bibliography .............................................................................................................................................................................................................................35

iv © ISO 2018 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Stan
...

SLOVENSKI STANDARD
SIST EN ISO 19085-10:2019
01-december-2019
Nadomešča:
SIST EN 1870-19:2014

Lesnoobdelovalni stroji - Varnost - 10. del: Žage, ki se uporabljajo na gradbišču

(ISO 19085-10:2018)

Woodworking machines - Safety - Part 10: Building site saws (contractor saws) (ISO

19085-10:2018)

Holzbearbeitungsmaschinen - Sicherheit - Teil 10: Baustellenkreissägemaschinen (ISO

19085-10:2018)
Machines à bois - Sécurité - Partie 10: Scies de chantier (ISO 19085-10:2018)
Ta slovenski standard je istoveten z: EN ISO 19085-10:2019
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN ISO 19085-10:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19085-10:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 13.110; 79.120.10 Supersedes EN 1870-19:2013
English Version
Woodworking machines - Safety - Part 10: Building site
saws (contractor saws) (ISO 19085-10:2018, Corrected
version 2018-11)

Machines à bois - Sécurité - Partie 10: Scies de chantier Holzbearbeitungsmaschinen - Sicherheit - Teil 10:

(ISO 19085-10:2018, Version corrigée 2018-11) Baustellenkreissägemaschinen (ISO 19085-10:2018)

This European Standard was approved by CEN on 16 October 2017.

This European Standard was corrected and reissued by the CEN-CENELEC Management Centre on 09 October 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-10:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Annex ZA (informative) Relationship between this European Standard and the essential

requirements of EU Directive 2006/42/EC/ aimed to be covered ................................................ 4

---------------------- Page: 4 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
European foreword

This document (EN ISO 19085-10:2019) has been prepared by Technical Committee ISO/TC 39

"Machine tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines -

Safety” the secretariat of which is held by UNI.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by December 2019, and conflicting national standards

shall be withdrawn at the latest by December 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 1870-19:2013.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association, and supports essential requirements of EU Directive(s).

For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this

document.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 19085-10:2018, Corrected version 2018-11 has been approved by CEN as

EN ISO 19085-10:2019 without any modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC/ aimed to be covered

This European Standard has been prepared under a Commission’s standardization request “M/396” to

provide one voluntary means of conforming to essential requirements of the new approach Machinery

Directive 2006/42.

Once this standard is cited in the Official Journal of the European Union under that Directive,

compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of

the scope of this standard, a presumption of conformity with the corresponding essential requirements

of that Directive, and associated EFTA regulations.

Table ZA.1 — Correspondence between this European Standard and Directive 2006/42/EC

Essential Requirements (ERs) of Directive Clause(s)/subclause(s) Remarks/Notes
2006/42/EC of this EN
1.1.2 Principles of safety integration
a) fitted for its function Clause 5, 6, 7, 8
b) eliminate or reduce the risks, give measures, inform Clause 5, 6, 7, 8
c) intended use and reasonably foreseeable misuse Clause 5, 6, 7, 8
d) constraints in use 7.5, 8.3
e) equipment 6.1
1.1.3 Materials and products 6.2
1.1.4 Lighting 8.3
1.1.5 Design of machinery to facilitate its handling 8.3
1.1.6 Ergonomics 7.5
1.1.7 Operating position 5.2
1.2.1 Safety and reliability of control systems 5.1, 5.8, 5.12, 7.11
1.2.2 Control devices 5.2, 5.3, 5.4
1.2.3 Starting 5.3
1.2.4 Stopping 5.4, 5.5, 6.4
1.2.4.1 Normal stop 5.4.2
1.2.6 Failure of the power supply 5.8
1.2.8 Software 5.1
1.3.1 Risk of loss of stability 6.1, 8.3
1.3.2 Risk of break-up during operation 6.2, 8.3
1.3.3 Risks due to falling or ejected objects 6.2, 6.3, 6.5, 6.9, 8.3
---------------------- Page: 6 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)
1.3.4 Risk due to surfaces, edges or angles
1.3.7 Risks related to moving parts 6.5, 6.6, 8.3
1.3.8 Choice of protection against risks related to moving 6.6, 8.3
parts
1.3.8.1 Moving transmission parts 6.6.3
1.3.8.2 Moving parts involved in the process 6.6.2
1.4.1 General requirements 6.9
1.4.2.1 Fixed guards 6.5.1
1.4.2.3 Adjustable guards restricting access 6.6.2
1.5.1 Electricity supply 7.13
1.5.2 Static electricity 7.11
1.5.4 Errors of fitting 7.12
1.5.6 Fire 7.1
1.5.8 Noise 7.2
1.5.11 External radiation 7.9
1.5.12 Laser equipment 7.10
1.5.13 Emission of hazardous materials and substances 7.3
1.6.1 Machinery maintenance 7.14, 8.3
1.6.2 Access to operating position and servicing points 7.14, 8.3
1.6.3 Isolation of energy sources 7.13, 8.3
1.6.4 Operator intervention 7.14, 8.3
1.6.5 Cleaning of internal parts 7.14, 8.3
1.7.1 Information and warnings on the machinery 7.10, 8.1, 8.2
1.7.2 Warning devices 7.10, 8.1
1.7.3 Marking of machinery 8.2
1.7.4 Instructions 7.10, 8.3
2.3 Machinery for working wood and analogous materials
a) guiding 6.10, 6.11
b) ejection 6.2, 6.3, 6.5, 6.6, 6.9, 8.3
c) brake 5.5, 6.4
d) accidental tool contact 6.6.2
---------------------- Page: 7 ----------------------
SIST EN ISO 19085-10:2019
EN ISO 19085-10:2019 (E)

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European

Standard is maintained in the list published in the Official Journal of the European Union. Users of this

document should consult frequently the latest list published in the Official Journal of the European

Union.

WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of

this document.
---------------------- Page: 8 ----------------------
SIST EN ISO 19085-10:2019
INTERNATIONAL ISO
STANDARD 19085-10
First edition
2018-03
Corrected version
2018-11
Woodworking machines — Safety —
Part 10:
Building site saws (contractor saws)
Machines à bois — Sécurité —
Partie 10: Scies de chantier
Reference number
ISO 19085-10:2018(E)
ISO 2018
---------------------- Page: 9 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)
Contents Page

Foreword ..........................................................................................................................................................................................................................................v

Introduction ................................................................................................................................................................................................................................vi

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 2

4 List of significant hazards ........................................................................................................................................................................... 4

5 Safety requirements and measures for controls ................................................................................................................. 5

5.1 Safety and reliability of control systems ........................................................................................................................... 5

5.2 Control devices ....................................................................................................................................................................................... 5

5.3 Start .................................................................................................................................................................................................................. 6

5.4 Safe stops ..................................................................................................................................................................................................... 6

5.4.1 General...................................................................................................................................................................................... 6

5.4.2 Normal stop .......................................................................................................................................................................... 6

5.4.3 Operational stop ............................................................................................................................................................... 6

5.4.4 Emergency stop ................................................................................................................................................................ 6

5.5 Braking function of tool spindles ............................................................................................................................................ 6

5.6 Mode selection ........................................................................................................................................................................................ 6

5.7 Spindle speed changing ................................................................................................................................................................... 6

5.7.1 Spindle speed changing by changing belts on the pulleys ........................................................... 6

5.7.2 Spindle speed changing by incremental speed change motor ................................................. 6

5.7.3 Infinitely variable speed by frequency inverter .................................................................................... 6

5.8 Failure of any power supply ........................................................................................................................................................ 6

5.9 Manual reset control .......................................................................................................................................................................... 7

5.10 Enabling control ..................................................................................................................................................................................... 7

5.11 Machine moving parts speed monitoring ........................................................................................................................ 7

5.12 Time delay ................................................................................................................................................................................................... 7

6 Safety requirements and measures for protection against mechanical hazards ..............................7

6.1 Stability .......................................................................................................................................................................................................... 7

6.1.1 Stationary machines ..................................................................................................................................................... 7

6.1.2 Displaceable machines ............................................................................................................................................... 7

6.2 Risk of break-up during operation ......................................................................................................................................... 7

6.3 Tool holder and tool design.......................................................................................................................................................... 7

6.3.1 General...................................................................................................................................................................................... 7

6.3.2 Spindle locking .................................................................................................................................................................. 7

6.3.3 Circular saw blade fixing device ......................................................................................................................... 8

6.3.4 Flange dimensions for circular saw blades ............................................................................................... 8

6.4 Braking ........................................................................................................................................................................................................... 8

6.4.1 Braking of tool spindles ............................................................................................................................................. 8

6.4.2 Maximum run-down time ........................................................................................................................................ 8

6.4.3 Brake release ....................................................................................................................................................................... 8

6.5 Safeguards ................................................................................................................................................................................................... 8

6.5.1 Fixed guards ......................................................................................................................................................................... 8

6.5.2 Interlocking movable guards................................................................................................................................. 8

6.5.3 Hold-to-run control ....................................................................................................................................................... 8

6.5.4 Two hand control ............................................................................................................................................................ 8

6.5.5 Electro-sensitive protection equipment (ESPE) ................................................................................... 8

6.5.6 Pressure sensitive protection equipment (PSPE) ............................................................................... 8

6.6 Prevention of access to moving parts .................................................................................................................................. 9

6.6.1 General...................................................................................................................................................................................... 9

6.6.2 Guarding of tools .............................................................................................................................................................. 9

6.6.3 Guarding of drives .......................................................................................................................................................13

6.6.4 Guarding of shearing and/or crushing zones ......................................................................................13

© ISO 2018 – All rights reserved iii
---------------------- Page: 11 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)

6.7 Impact hazard .......................................................................................................................................................................................13

6.8 Clamping devices ...............................................................................................................................................................................14

6.9 Measures against ejection ..........................................................................................................................................................14

6.9.1 General...................................................................................................................................................................................14

6.9.2 Guards material and characteristics ............................................................................................................14

6.9.3 Anti-kickback devices ...............................................................................................................................................14

6.10 Work-piece support and guides ............................................................................................................................................18

6.10.1 Rip fence ...............................................................................................................................................................................18

6.10.2 Cross-cut fence ...............................................................................................................................................................19

6.10.3 Machine table ...................................................................... .............................................................................................19

6.10.4 Extension table ...............................................................................................................................................................19

6.11 Safety appliances ................................................................................................................................................................................19

7 Safety requirements and measures for protection against other hazards ...........................................20

7.1 Fire ......... .........................................................................................................................................................................................................20

7.2 Noise .............................................................................................................................................................................................................21

7.2.1 Noise reduction at the design stage .............................................................................................................21

7.2.2 Noise emission measurement ...........................................................................................................................21

7.3 Emission of chips and dust ........................................................................................................................................................21

7.4 Electricity ..................................................................................................................................................................................................21

7.4.1 General...................................................................................................................................................................................21

7.4.2 Displaceable machines ............................................................................................................................................21

7.5 Ergonomics and handling ...........................................................................................................................................................21

7.6 Lighting .......................................................................................................................................................................................................21

7.7 Pneumatics ..............................................................................................................................................................................................21

7.8 Hydraulics ................................................................................................................................................................................................22

7.9 Electromagnetic compatibility ...............................................................................................................................................22

7.10 Laser ..............................................................................................................................................................................................................22

7.11 Static electricity ...................................................................................................................................................................................22

7.12 Errors of fitting ....................................................................................................................................................................................22

7.13 Isolation .....................................................................................................................................................................................................22

7.14 Maintenance ...........................................................................................................................................................................................22

8 Information for use .........................................................................................................................................................................................22

8.1 Warning devices ..................................................................................................................................................................................22

8.2 Markings ....................................................................................................................................................................................................22

8.2.1 General...................................................................................................................................................................................22

8.2.2 Additional markings ..................................................................................................................................................22

8.3 Instruction handbook ....................................................................................................................................................................23

8.3.1 General...................................................................................................................................................................................23

8.3.2 Additional information ............................................................................................................................................23

Annex A (informative) Performance level required ..........................................................................................................................24

Annex B (normative) Test for braking function .....................................................................................................................................25

Annex C (normative) Stability test for displaceable machines ..............................................................................................26

Annex D (normative) Impact test for guards ............................................................................................................................................27

Annex E (normative) Noise emission measurement for machines not in ISO 7960:1995 .........................28

Annex F (normative) Frame rigidity test .......................................................................................................................................................29

Annex G (normative) Saw blade guard rigidity test ...........................................................................................................................30

Annex H (normative) Minimum dimensions of machine table, extension table and table insert .....31

Annex I (normative) Riving knife longitudinal and lateral rigidity test .......................................................................32

Annex J (normative) Dimensions of test probe ......................................................................................................................................34

Bibliography .............................................................................................................................................................................................................................35

iv © ISO 2018 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 19085-10:2019
ISO 19085-10:2018(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.