EN 14423:2013/prA1
(Amendment)Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar
Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18 bar
This European Standard specifies the design, materials and dimensions of fittings for clamp type coupling assemblies for use with nominal sizes DN 15 to DN 50 steam and hot water hoses. It covers assemblies up to a maximum working pressure of 18 bar ) (corresponding to a saturated steam temperature of 210 °C).
Schlaucharmaturen mit Klemmfassung für Dampf bis 18 bar
Raccords avec colliers de serrage pour tuyaux à vapeur utilisant une pression jusqu'à 18 bar
Cevne armature z objemkami za cevi za paro do 18 bar
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2016
Cevne armature z objemkami za cevi za paro do 18 bar
Clamp type coupling assemblies for use with steam hoses rated for pressures up to 18
bar
Schlaucharmaturen mit Klemmfassung für Dampf bis 18 bar
Raccords avec colliers de serrage pour tuyaux à vapeur utilisant une pression jusqu'à 18
bar
Ta slovenski standard je istoveten z: EN 14423:2013/prA1
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
EN 14423:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
January 2016
ICS 23.040.70
English Version
Clamp type coupling assemblies for use with steam hoses
rated for pressures up to 18 bar
Raccords avec colliers de serrage pour tuyaux à vapeur Schlaucharmaturen mit Klemmfassung für Dampf bis
utilisant une pression jusqu'à 18 bar 18 bar
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 218.
This draft amendment A1, if approved, will modify the European Standard EN 14423:2013. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14423:2013/prA1:2016 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Modification to 5.1, Design . 4
2 Deletion of 7.3.6, Hose fittings with coned end .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.