CEN/TS 14906:2004
(Main)Leather - Upholstery leather characteristics - Guide for the selection of leather for automotive
Leather - Upholstery leather characteristics - Guide for the selection of leather for automotive
This document gives guidelines for the test methods and recommended values for upholstery leather for automotive. This document also specifies the sampling and conditioning procedures of specimens.
Leder - Richtwerte für Polsterleder - Leitfaden zur Auswahl von Automobilleder
Diese Technische Spezifikation enthält Richtlinien für die Prüfverfahren und empfohlenen Richtwerte für Polsterleder in Kraftfahrzeugen. In dieser Technischen Spezifikation werden im Weiteren die Verfahren für Probenahme und Konditionierung der Proben festgelegt.
Cuir - Caractéristiques du cuir de garnissage - Guide pour la sélection de cuir pour l'automobile
La présente Spécification technique donne des lignes directrices relatives aux méthodes d'essais et des valeurs recommandées pour le cuir de garnissage destiné à l'industrie automobile. La présente Spécification technique spécifie également les modes opératoires d'échantillonnage et de conditionnement des échantillons.
Usnje - Značilnosti usnja za oblazinjenje - Vodilo za izbiro usnja za uporabo v avtomobilih
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2005
8VQMH=QDþLOQRVWLXVQMD]DREOD]LQMHQMH9RGLOR]DL]ELURXVQMD]DXSRUDERY
DYWRPRELOLK
Leather - Upholstery leather characteristics - Guide for the selection of leather for
automotive
Leder - Richtwerte für Polsterleder - Leitfaden zur Auswahl von Automobilleder
Cuir - Caractéristiques du cuir de garnissage - Guide pour la sélection de cuir pour
l'automobile
Ta slovenski standard je istoveten z: CEN/TS 14906:2004
ICS:
43.020 Cestna vozila na splošno Road vehicles in general
59.140.30 Usnje in krzno Leather and furs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
TECHNICAL SPECIFICATION
CEN/TS 14906
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
October 2004
ICS 59.140.30
English version
Leather - Upholstery leather characteristics - Guide for the
selection of leather for automotive
Cuir - Caractéristiques du cuir de garnissage - Guide pour Leder - Richtwerte für Polsterleder - Leitfaden zur Auswahl
la sélection de cuir pour l'automobile von Automobilleder
This Technical Specification (CEN/TS) was approved by CEN on 26 August 2004 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14906:2004: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 General principles.6
5 Sampling.6
6 Conditioning and sampling preparation .6
7 Characteristics, test methods and recommended values.6
8 Test report .6
Annex A (normative) Characteristics, test methods and recommended levels for upholstery
leather for automotive .8
Bibliography .10
Foreword
This document (CEN/TS 14906:2004) has been prepared by Technical Committee CEN/TC 289 “Leather”, the
secretariat of which is held by UNI.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
Introduction
This document was prepared by CEN/TC 289 Leather in order to provide the leather and the automotive
industries with guidelines on which seller and buyer can base their negotiations.
1 Scope
This document gives guidelines for the test methods and recommended values for upholstery leather for
automotive. This document also specifies the sampling and conditioning procedures of specimens.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 14288, Leather - Physical and mechanical tests - Determination of fogging characteristics
EN 14326, Leather - Physical and mechanical tests - Determination of resistance to horizontal spread of flame
EN 14327, Leather - Physical and mechanical tests - Determination of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.