Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units

This European Standard applies to machines for de-wiring bales and units and shall be used together with
EN 1034-1:2000. It deals with all significant hazards, hazardous situations and hazard events relevant to
machines for de-wiring bales and units, when used as intended and under conditions reasonably foreseeable
by the manufacturer as incorrect application (see clause 4).
This European Standard is not applicable to hand-held devices.
This European Standard is not applicable to machines for de-wiring bales and units which are manufactured
before the date of publication of this document by CEN.

Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 13: Maschinen zur Entdrahtung von Ballen und Units

Diese Europäische Norm gilt für Maschinen zur Entdrahtung von Ballen und Units und ist gemeinsam mit
EN 1034-1:2000 anzuwenden. Sie behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Maschinen zur Entdrahtung von Ballen und Units zutreffen, wenn sie bestimmungsgemäß und unter Bedingungen, die vom Hersteller als Fehlanwendung vernünftigerweise vorhersehbar sind, verwendet werden (siehe Abschnitt 4).
Diese Europäische Norm gilt nicht für handgehaltene Maschinen.
Diese Europäische Norm gilt nicht für Maschinen zur Entdrahtung von Ballen und Units, die vor der Veröffentlichung als EN hergestellt wurden.

Sécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 13: Machines à couper les fils des balles et unités

Le présent document s‘applique aux machines à couper les fils des balles et des unités et doit être appliqué conjointement avec l'EN 1034-1:2000. Il traite de l'ensemble des phénomènes, situations et événements dangereux significatifs qui concernent les machines à couper les fils des balles et des unités lorsque celles-ci sont utilisées normalement et dans les conditions d’utilisation abusive qui peuvent raisonnablement être prévues par le fabricant (voir Article 4).
Cette norme n‘est pas applicable aux machines tenues à la main.
Cette norme n‘est pas applicable aux machines à couper les fils des balles et des unités, qui ont été fabriquées avant la publication de la présente norme par le CEN.

Varnost strojev – Varnostne zahteve za načrtovanje in konstrukcijo strojev in opreme za izdelavo papirja – 13. del: Stroji za razvezovanje bal in enot

General Information

Status
Withdrawn
Publication Date
15-Nov-2005
Withdrawal Date
01-Dec-2009
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
02-Dec-2009
Completion Date
02-Dec-2009

Relations

Buy Standard

Standard
EN 1034-13:2006
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit von Maschinen - Sicherheitstechnische Anforderungen an Konstruktion und Bau von Maschinen der Papierherstellung und Ausrüstung - Teil 13: Maschinen zur Entdrahtung von Ballen und UnitsSécurité des machines - Prescriptions de sécurité pour la conception et la construction de machines de fabrication et de finition du papier - Partie 13: Machines a couper les fils des balles et unitésSafety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 13: Machines for de-wiring bales and units85.100Oprema za papirno industrijoEquipment for the paper industry21.020Characteristics and design of machines, apparatus, equipment13.110Varnost strojevSafety of machineryICS:Ta slovenski standard je istoveten z:EN 1034-13:2005SIST EN 1034-13:2006en01-julij-2006SIST EN 1034-13:2006SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1034-13November 2005ICS 85.100 English VersionSafety of machinery - Safety requirements for the design andconstruction of paper making and finishing machines - Part 13:Machines for de-wiring bales and unitsSécurité des machines - Exigences techniques de sécuritépour la conception et la construction de machines defabrication et de finition du papier - Partie 13: Machines àcouper les files des balles et unitès des ballesSicherheit von Maschinen - SicherheitstechnischeAnforderungen an Konstruktion und Bau von Maschinender Papierherstellung und Ausrüstung - Teil 13: Maschinenzur Entdrahtung von Ballen und UnitsThis European Standard was approved by CEN on 6 October 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1034-13:2005: ESIST EN 1034-13:2006

Relationship between this
European
Standard and the Essential Requirements
of EU Directive 98/37/EC.13
Figures Figure 1 — Example of a machine for cutting bale wires.6 Figure 2 — Example of a machine for unit de-wiring.6 Figure 3 — Example of a machine for de-wiring cellulose bales.7
Tables
Table 1 —
List of significant hazards.8 Table 2 — Methods used to verify safety requirements and/or measures.12
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this European Standard.
For machines that have been designed and built according to the provisions of this C standard, the following stipulation applies: When provisions of this type C standard are different from those which are stated in type B standards or from provisions made in EN 1034-1:2000, the provisions of this type C standard take precedence over the provisions of the other standards. 1 Scope This European Standard applies to machines for de-wiring bales and units and shall be used together with
EN 1034-1:2000. It deals with all significant hazards, hazardous situations and hazard events relevant to machines for de-wiring bales and units, when used as intended and under conditions reasonably foreseeable by the manufacturer as incorrect application (see clause 4).
This European Standard is not applicable to hand-held devices. This European Standard is not applicable to machines for de-wiring bales and units which are manufactured before the date of publication of this document by CEN. 2 Normative references The following referenced documents are indispensable for the application of this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 294:1992, Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs EN 418:1992, Safety of machinery — Emergency stop equipment — Functional aspects — Principles for design EN 619:2002, Continuous conveyors and systems — Safety and EMC requirements for mechanical conveying systems for packaged goods EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards EN 954-1:1996, Safety of machinery — Safety related parts of control systems — Part 1: General principles for design EN 982:1996, Safety of machinery — Safety requirements for fluid power systems and their components — Hydraulics EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components —Pneumatics SIST EN 1034-13:2006

(IEC 60204-1:1997)
EN 61000-6-2:2001, Electromagnetic compatibility (EMC) — Part 6-2: Generic standard — Immunity —
Part 2: Industrial environment (IEC 61000-6-2:1999, modified) EN 61496-1:2004, Safety of machinery — Electro-sensitive protective equipment — Part 1: General requirements and tests (IEC 61496-1:2004, modified) prEN 61496-2:1997, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:1997, modified) EN ISO12100-1:2003, Safety of machinery — Basic concepts — General principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts — General principles for design - Part 2: Technical principles and specifications (ISO 12100-2:2003)
3 Terms and definitions For the purpose of this European Standard, the definitions given in EN 1034-1:2000, EN ISO 12100-1:2003 and the following apply: 3.1 machine for de-wiring bales and units
machinery used for cutting and or opening and removing wires used for binding together bales made of cellulose or paper and units formed of cellulose bales. This machinery includes the de-wiring device, integrated continuous conveyor for moving the bales and units, the loading conveyor, the positioning device and the wire ejection device, including the drive and control systems.
Examples of machine types are illustrated in Figures 1, 2 and 3.
NOTE Safety devices are not shown Key 1 Loading conveyor 2 Movable blade 3 Control cabinet Figure 1 — Example of a machine for cutting bale wires
NOTE Safety devices are not shown Key 1 Wire ejection 2 Feed direction 3 Cutting tool Figure 2 — Example of a machine for unit de-wiring 1 2 3 SIST EN 1034-13:2006

NOTE Safety devices are not shown Key 1 Feed direction 2 Movable cutting tool 3 Loading conveyor
4 Positioning device 5 Continuous conveyor Figure 3 — Example of a machine for de-wiring cellulose bales 3.2 de-wiring device device with tools for cutting/opening, gripping and removing the wires, including drive 3.3 loading conveyor continuous conveyor for transporting bales or units to the feeding point of the de-wiring device
3.4 positioning device system with sliders that push the bales or units into the position required on the convenyer for de-wiring 3.5 wire ejection device device used for removing the wire from the machine 3.6 unit combination of several bales made of cellulose held together by wires
4 List of significant hazards This clause contains all the significant hazards, hazardous situations and events, as far as they are dealt with in this standard, which are identified by risk assessment as significant for this type of machinery and which require action to eliminate or reduce the risk.
Table 1 —
List of significant hazards Significant hazards EN 1034-13:2005 EN 1034-1:2000 Mechanical hazards
Crushing hazard 5.2.1; 5.2.2; 5.2.5 5.1 Shearing hazard 5.2.1; 5.2.2; 5.2.5 5.1; 5.11; 5.12 Cutting or severing hazard 5.2.1 5.2 Entanglement hazard 5.2.1 5.1; 5.4 Drawing-in or trapping hazard 5.2.3; 5.2.4 5.1 Stabbing or puncture hazard 5.2.1; 5.3 5.1 High-pressure fluid ejection hazard 5.15; 5.16 5.24 Ejection of parts
5.3 5.2 Slip, trip and fall hazards in relationship with machines
5.3 5.5 Electrical hazards, for example
Electrical con
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.