EN ISO 13088:2012
(Main)Gas cylinders - Acetylene cylinder bundles - Filling conditions and filling inspection (ISO 13088:2011)
Gas cylinders - Acetylene cylinder bundles - Filling conditions and filling inspection (ISO 13088:2011)
ISO 13088:2011 specifies the minimum requirements for the filling conditions and filling inspection of acetylene cylinder bundles. It applies both to both bundles which are filled while the cylinders are assembled in the bundle and to bundles of which the cylinders are filled as individual cylinders and are assembled into a bundle after filling. It does not apply to bundles containing solvent-free acetylene cylinders.
ISO 13088:2011 is not applicable to individual acetylene cylinders that are not intended to be assembled into a bundle (see ISO 11372).
Gasflaschen - Acetylenflaschenbündel - Füllbedingungen und Inspektion beim Füllen (ISO 13088:2011)
Diese Internationale Norm legt die Mindestanforderungen für die Füllbedingungen und die Inspektion beim Füllen von Acetylenflaschenbündeln fest. Sie gilt sowohl für Bündel, welche gefüllt werden während die Flaschen im Bündel eingebaut sind als auch für Bündel, bei denen die Flaschen als Einzelflaschen gefüllt und nach dem Füllen in ein Bündel eingebaut werden. Sie gilt nicht für Bündel, die lösemittelfreie Acetylenflaschen enthalten. Diese Internationale Norm gilt nicht für einzelne Acetylenflaschen, die nicht für den Einbau in ein Bündel vorgesehen sind (siehe ISO 11372).
Bouteilles à gaz - Cadres de bouteilles d'acétylène - Conditions de remplissage et contrôle au remplissage (ISO 13088:2011)
L'ISO 13088:2011 spécifie les exigences minimales relatives aux conditions de remplissage et au contrôle au remplissage des cadres de bouteilles d'acétylène. Elle s'applique et aux cadres dont les bouteilles sont remplies quand elles sont placées dans le cadre, et aux cadres dont les bouteilles sont remplies individuellement puis placées dans le cadre après remplissage. Elle ne s'applique pas aux cadres contenant des bouteilles d'acétylène sans solvant.
L'ISO 13088:2011 ne s'applique pas aux bouteilles d'acétylène individuelles qui ne sont pas destinées à être montées dans un cadre (voir l'ISO 11372).
Plinske jeklenke - Snopi jeklenk za acetilen - Pogoji in kontrola polnjenja (ISO 13088:2011)
Ta mednarodni standard določa minimalne zahteve za pogoje in kontrolo polnjenja snopov jeklenk za acetilen. Velja za snope, ki se polnijo med sestavljanjem jeklenk v snop, in za snope, v katerih se jeklenke polnijo posamično in so sestavljene v snop po polnjenju. Ne velja za snope, ki vsebujejo jeklenke za acetilen brez topila. Ta mednarodni standard ne velja za posamezne jeklenke za acetilen, ki niso namenjene za sestavljanje v snope (glejte ISO 11372).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2012
1DGRPHãþD
SIST EN 12755:2001
Plinske jeklenke - Snopi jeklenk za acetilen - Pogoji in kontrola polnjenja (ISO
13088:2011)
Gas cylinders - Acetylene cylinder bundles - Filling conditions and filling inspection (ISO
13088:2011)
Gasflaschen - Flaschenbündel für Acetylen - Füllbedingungen und Inspektion beim
Füllen (ISO 13088:2011)
Bouteilles à gaz - Cadres de bouteilles d'acétylène - Conditions de remplissage et
contrôle de remplissage (ISO 13088:2011)
Ta slovenski standard je istoveten z: EN ISO 13088:2012
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 13088
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2012
ICS 23.020.30 Supersedes EN 12755:2000
English Version
Gas cylinders - Acetylene cylinder bundles - Filling conditions
and filling inspection (ISO 13088:2011)
Bouteilles à gaz - Cadres de bouteilles d'acétylène - Gasflaschen - Acetylenflaschenbündel - Füllbedingungen
Conditions de remplissage et contrôle au remplissage (ISO und Inspektion beim Füllen (ISO 13088:2011)
13088:2011)
This European Standard was approved by CEN on 6 October 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13088:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 13088:2011 has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 13088:2012 by
Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the
latest by April 2013.
This European Standard has been submitted for reference into the RID and/or in the technical annexes of the
ADR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12755:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13088:2011 has been approved by CEN as a EN ISO 13088:2012 without any modification.
INTERNATIONAL ISO
STANDARD 13088
First edition
2011-12-15
Gas cylinders — Acetylene cylinder
bundles — Filling conditions and filling
inspection
Bouteilles à gaz — Cadres de bouteilles d'acétylène — Conditions de
remplissage et contrôle de remplissage
Reference number
ISO 13088:2011(E)
©
ISO 2011
ISO 13088:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 13088:2011(E)
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Basic requirements for acetylene cylinder bundles . 4
4.1 General . 4
4.2 Filling conditions . 4
5 Assembly, marking and documentation of acetylene cylinder bundles . 5
5.1 Assembly . 5
5.2 Verification of marking and necessary documentation . 5
5.3 Documentation . 6
6 Filling inspection for acetylene cylinder bundles . 6
6.1 Pre-fill inspection . 6
6.2 Solvent content . 7
6.3 Number of consecutive fillings . 8
6.4 Inspection during filling . 8
6.5 Post-fill inspection . 8
7 Individual filling of acetylene bundle cylinders . 9
Annex A (normative) Procedure for establishing the filling conditions of acetylene cylinder
bundles . 10
Annex B (normative) Determination of the solvent content in the bundle in the course of the
filling inspection . 14
Bibliography . 16
ISO 13088:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13088 was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 4,
Operational requirements for gas cylinders.
iv © ISO 2011 – All rights reserved
ISO 13088:2011(E)
Introduction
This International Standard aims at the harmonization of the different operating and filling conditions of
acetylene cylinder bundles and covers requirements that reflect current practice and experience regarding
inspection at the time of filling.
Where there is any conflict between this International Standard and any applicable regulation, the regulation
always takes precedence.
In International Standards, weight is equivalent to a force, expressed in newtons. However, in common
parlance (as used in terms defined in this International Standard), the word “weight” continues to be used to
mean “mass”, but this practice is deprecated (see ISO 80000-4).
In this International Standard the unit bar is used, due to its universal use in the field of technical gases. It
should, however, be noted that bar is not an SI unit, and that the according SI unit for pressure is pascal (Pa).
Pressure values given in this International Standard are given as gauge pressure (pressure exceeding
atmospheric pressure) unless noted otherwise.
INTERNATIONAL STANDARD ISO 13088:2011(E)
Gas cylinders — Acetylene cylinder bundles — Filling
conditions and filling inspection
1 Scope
This International Standard specifies the minimum requirements for the filling conditions and filling inspection
of acetylene cylinder bundles. It applies both to bundles which are filled while the cylinders are assembled in
the bundle and to bundles of which the cylinders are filled as individual cylinders and are assembled into a
bundle after filling. It does not apply to bundles containing solvent-free acetylene cylinders.
This International Standard is not applicable to individual acetylene cylinders that are not intended to be
assembled into a bundle (see ISO 11372).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 11372, Gas cylinders — Acetylene cylinders — Filling conditions and filling inspection
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
acetylene cylinder
cylinder manufactured and suitable for the transport of acetylene, containing a porous material and solvent for
acetylene, with a valve and other accessories affixed to the cylinder
NOTE When there is no risk of ambiguity, the word “cylinder” is used.
3.2
acetylene cylinder bundle
transportable unit comprising of at least 2 cylinders up to and usually not exceeding 16 cylinders that are
permanently connected together by a manifold and contained within a rigid frame equipped with all necessary
equipment for filling and use
3.3
cylinder shell
acetylene cylinders empty cylinder manufactured and suitable for receiving and containing a porous material
for use as part of an acetylene cylinder
3.4
filler
gas cylinders trained person responsible for inspection prior to, during and immediately after filling
ISO 13088:2011(E)
3.5
maximum acetylene content
acetylene cylinder bundles specified maximum weight of acetylene including saturation acetylene in t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.