prEN ISO 8675
(Main)Hexagon thin nuts (style 0) chamfered, with fine pitch thread - Product grades A and B (ISO/DIS 8675:2016)
Hexagon thin nuts (style 0) chamfered, with fine pitch thread - Product grades A and B (ISO/DIS 8675:2016)
Niedrige Sechskantmuttern mit Fase (Typ 0), mit Feingewinde - Produktklassen A und B (ISO/DIS 8675:2016)
Écrous hexagonaux bas (style 0) chanfreinés, à pas fin - Grades A et B (ISO/DIS 8675:2016)
Vezni elementi - Šestrobe nizke matice (tip 0) z drobnim navojem (ISO/DIS 8675:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 8675:2022
01-junij-2022
Vezni elementi - Šestrobe nizke matice (tip 0) z drobnim navojem (ISO/DIS
8675:2022)
Fasteners - Hexagon thin nuts (style 0), with fine pitch thread (ISO/DIS 8675:2022)
Mechanische Verbindungselemente – Niedrige Sechskantmuttern (Typ 0), mit
metrischem Feingewinde (ISO/DIS 8675:2022)
Fixations - Écrous hexagonaux bas (style 0), à pas fin (ISO/DIS 8675:2022)
Ta slovenski standard je istoveten z: prEN ISO 8675
ICS:
21.040.10 Metrski navoji Metric screw threads
21.060.20 Matice Nuts
oSIST prEN ISO 8675:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8675:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8675:2022
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8675
ISO/TC 2/SC 12 Secretariat: DIN
Voting begins on: Voting terminates on:
2022-04-28 2022-07-20
Fasteners — Hexagon thin nuts (style 0), with fine pitch
thread
Fixations — Écrous hexagonaux bas (style 0), à pas fin
ICS: 21.060.20
IMPORTANT — Please use this updated version dated 2022-04-08, and discard
any previous version of this DIS.
Modifications of the layout
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8675:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8675:2022
ISO/DIS 8675:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8675:2022
ISO/DIS 8675:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions .2
5 Requirements and reference International Standards . 3
6 Marking and labelling . 4
6.1 Marking on product . . 4
6.2 Labelling on package . 4
7 Designation .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.