iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 3032:1994

(Main)

Aerospace series - Test method for dry film lubricants - Thickness measurement

Aerospace series - Test method for dry film lubricants - Thickness measurement

This standard specifies a test method to measure the thickness of a dry film lubricant.

Luft- und Raumfahrt - Prüfverfahren für Trockenschmierstoffilm - Messung der Dicke

Diese Norm legt ein Prüfverfahren zur Messung der Dicke eines Trockenschmiermittelfilms fest.

Série aérospatiale - Méthode d'essai pour films lubrifiants solides - Mesurage de l'épaisseur

La présente norme spécifie une méthode d'essai pour mesurer l'épaisseur d'un film lubrifiant solide.

Aerospace series - Test method for dry film lubricants - Thickness measurement

General Information

Status
Published
Publication Date
09-Jan-1994
Withdrawal Date
30-Jul-1994
ICS
49.035 - Components for aerospace construction
Technical Committee
ASD-STAN - Aerospace
Drafting Committee
ASD-STAN/D 4 - Metallic
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
30-Jun-2017
Ref Project
SIST EN 3032:2001 - Aerospace series - Test method for dry film lubricants - Thickness measurement

Buy Standard

EN 3032:2001EN 3032:2001
PreviousNext
Standard
EN 3032:2001
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Test method for dry film lubricants - Thickness measurementLuft- und Raumfahrt - Prüfverfahren für Trockenschmierstoffilm - Messung der DickeSérie aérospatiale - Méthode d'essai pour films lubrifiants solides - Mesurage de l'épaisseurAerospace serie
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 2588:2024(Main)
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
SIST EN 2588:2024

This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
-   ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
-   synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4157:2024(Main)
Aerospace series - Rod end, with self-aligning double row ball bearing and threaded shank in steel - Dimensions and loads, Inch series
SIST EN 4157:2024

This document specifies the characteristics of adjustable rod-ends with self-aligning double row ball bearing and threaded shank in steel.
They consist of:
-   a rod-end comprising:
-   either seals or shields;
-   an optional longitudinal groove for locking purpose;
-   an inner ring with balls.
These rod-ends are intended for use with flight control rods or rods for aerospace structures.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4905:2023(Main)
Aerospace series - Passive UHF RFID for airborne use
SIST EN 4905:2023

This document is applicable to new manufactured tags after publication of this document.
This document aims to:
-   provide specification for RFID tag manufacturers to design and manufacture passive UHF RFID tags for the aeronautical industry;
-   identify required performances for UHF RFID tags in order to be read/written during ground operations only, while being subject to the global flight environment;
-   identify functional and environmental validation tests to be performed on passive UHF RFID tags with associated pass/fail criteria as well as associated test methods;
-   check functionalities and resistance to environment for airborne passive UHF RFID tags.
This document does not apply to:
-   the reader (interrogator – readers). It will be addressed appropriately by individual applicants;
-   active RFID devices or battery assisted passive (BAP) RFID devices;
-   RFID tags designed to operate outside the 860 MHz to 960 MHz frequency range.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4906:2023(Main)
Aerospace series - Embedded tags - Choice of fixation for installation, removal and replacement of embedded tags
SIST EN 4906:2023

This document is applicable in the aeronautical domain to on-board parts and to equipment intended to be embedded or positioned on any civil or military airborne vehicle with a type certificate.
The purpose of this document is to guide design, manufacturing, maintenance and operations organizations in the installation, removal and replacement of RFID tags (UHF and HF) and Contact Memory Buttons (CMB), according to the environments defined in RTCA DO-160/EUROCAE ED-14 and according to the type of support and the expected fixation performances. This guide will provide help in the specification of the tag installation/removal functions and/or will enable the solutions on offer from tag suppliers to be enhanced.
The term "tag" used in this document covers all the tags used to store electronic data, including RFID tags and CMB tags. As a reminder, the tags can also contain information that can be read by devices other than RFID or CMB readers (e.g. bar codes - Data Matrix, QR codes, etc., and/or alphanumerical characters) and information that can be read by the naked eye without any tools (human-readable).

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4880:2023(Main)
Aerospace series - General technical specification for standard parts
SIST EN 4880:2023

This document specifies the minimum requirements for the qualification, acceptance, delivery and
inspection of standard parts by the aerospace industry and its manufacturers.
This document is valid for standard parts and their assemblies as described in a product standard, if
mentioned therein. This specification can also be applied to other parts when specifically invoked by
the terms of delivery.
Parts/sections of this document are not applicable in cases where the product standard stipulates
requirements that differ from this specification.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4708-203:2022(Main)
Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 203: polyvinylidene fluoride (PVDF) Identification sleeves - Operating Temperature range -55ºC to 225ºC - Product Standard
SIST EN 4708-203:2023

This document specifies the required characteristics for heat-shrinkable semi rigid polyvinylidene identification sleeves for use in aircraft electrical systems at operating temperatures between -55 °C and 225 °C.
This specification is for the characterisation of Identification sleeves only.
This sleeving is a semi rigid tough product and is suitable for use where high temperatures and extreme fluid resistance properties are required.
It is available with a shrink ratio of 2:1.
The product is normally supplied with internal diameters up to 38 mm
The standard colours are white, black or yellow
For use at temperatures above 200 °C black with white or silver ink is recommended
Sizes or colours other than those specifically listed in this standard may be available. These items shall be considered to comply with this document if they comply with the property requirements listed in tables 2 and 3 except for dimensions and mass.
As the sleeving to be tested is a printed article the complete system is to be recorded as part of the evaluation. The sleeve will only be considered as meeting the requirements of this specification if printed with the printer, ribbon/inks and settings referenced within the test report.
Mark adherence and print permanence are determined in this document using method EN 6059-407.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4708-201:2022(Main)
Aerospace series - Sleeves, heat-shrinkable, for binding, insulation and identification - Part 201: Polyolefin identification sleeves - Operating Temperature range -55 °C to 135 °C - Product standard
SIST EN 4708-201:2023

This document specifies the required characteristics for heat-shrinkable polyolefin identification
sleeving for use in aircraft electrical systems at operating temperatures between −55 °C and 135 °C.
This specification is for the characterisation of identification sleeves only.
This sleeving is flexible and flame retarded, and is available with 2:1 and 3:1 shrink ratios.
The product is normally supplied with internal diameters up to 57 mm.
The standard colours are white or yellow.
Sizes or colours other than those specifically listed in this standard may be available. These items are
considered to comply with this document if they comply with the property requirements listed in tables 3
and 4 except for dimensions and mass.
As the sleeving to be tested is a printed article the complete system is to be recorded as part of the
evaluation. The sleeve will only be considered as meeting the requirements of this document if printed
with the printer, ribbon, inks, and settings referenced within the test report.
Mark adherence and print permanence are determined in this document using method EN 6059-407.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4841-1:2022(Main)
Aerospace series - Shock mount with bushes - Part 1: Technical specification
SIST EN 4841-1:2022

This document specifies the required characteristics, inspection and test methods, qualification and acceptance conditions for shock mounts with bushes, designed to withstand static and dynamic loads possible for aerospace interior applications in the temperature range from -55 °C to 85 °C.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 4841-2:2022(Main)
Aerospace series - Shock mount with bushes - Part 2: Technical overview
SIST EN 4841-2:2022

This document specifies the dimensions, masses, the tolerances and the required characteristics of shock mounts with bushes for aerospace interior application and without contamination by phosphate-ester hydraulic fluids.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 2755:2021(Main)
Aerospace series - Bearing, spherical, plain in corrosion resisting steel with self-lubricating liner - Elevated load at ambient temperature - Technical specification
SIST EN 2755:2022

This document specifies the required characteristics, inspection and test methods, qualification and acceptance conditions for a spherical plain bearing in corrosion resisting steel, with self-lubricating liner, for elevated loads at ambient temperature intended for use in fixed or moving parts of the aircraft structure and control mechanisms.
This document applies whenever referenced.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day