EN 2588:2024
(Main)Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly slots - Dimensions and loads
This document specifies the characteristics of spherical plain bearings in corrosion resisting steel, with assembly slots, metric series, with or without lubrication holes and groove, intended for use in fixed or moving parts of aircraft structure and control mechanisms, within the temperature range from −54 °C to 150 °C.
It also applies to the following temperature ranges when lubricated with the following greases (see EN 2337):
- ester type very high pressure grease (code letter A), operating range from −73 °C to 121 °C;
- synthetic hydrocarbon type very high pressure grease general purpose (code letter B), operating range from −54 °C to 177 °C.
Their field of application when lubricated with grease code letter A is limited to 121 °C.
Luft- und Raumfahrt - Gelenklager aus korrosionsbeständigem Stahl mit Einführnut - Maße und Belastungen
Dieses Dokument legt die Eigenschaften für Gelenklager aus korrosionsbeständigem Stahl mit Einführnut der metrischen Reihe mit oder ohne Schmierloch und Schmiernut fest, die für starre oder bewegte Flugwerkteile und deren Betätigungseinrichtungen bestimmt sind, innerhalb eines Temperaturbereichs von −54 °C bis 150 °C.
Es ist auch anwendbar für die folgenden Temperaturbereiche, wenn sie mit folgenden Fetten geschmiert sind (siehe EN 2337):
- Hochdruckfett auf Esterbasis (Kennbuchstabe A), Betriebstemperaturbereich von −73 °C bis 121 °C;
- Hochdruckfett auf der Basis von synthetischen Kohlenwasserstoffen zur allgemeinen Verwendung (Kennbuchstabe B), Betriebstemperaturbereich von −54 °C bis 177 °C.
Ihr Anwendungsbereich für Schmierung mit Fett A ist auf 121 °C eingeschränkt.
Série aérospatiale - Rotule lisse en acier résistant à la corrosion avec encoches d’assemblage - Dimensions et charges
Le présent document spécifie les caractéristiques des rotules lisses en acier résistant à la corrosion, avec des encoches d'assemblage, série métrique, avec ou sans trous et rainure de lubrification, destinées à être utilisées dans les éléments fixes ou mobiles de la structure des aéronefs et de leurs mécanismes de commande.
Elles peuvent être utilisées dans une plage de températures de −54 °C à 150 °C.
Cependant, comme elles sont lubrifiées avec les graisses suivantes (voir l’EN 2337) :
- graisse extrême pression, type ester (lettre code A), plage d'utilisation comprise entre −73 °C et 121 °C ou
- graisse extrême pression, type hydrocarbures synthétiques d’usage général (lettre code B), plage d'utilisation comprise entre −54 °C et 177 °C,
en cas de lubrification avec de la graisse code A, leur champ d'application est limité à 121 °C.
Aeronavtika - Ležaj, krogelni, drsni, iz korozijsko odpornega jekla z utorom - Mere in nosilnosti
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Aeronavtika - Ležaj, krogelni, drsni, iz korozijsko odpornega jekla z utorom - Mere
in nosilnosti
Aerospace series - Bearing, spherical plain in corrosion resisting steel with assembly
slots - Dimensions and loads
Luft- und Raumfahrt - Gelenklager aus korrosionsbeständigem Stahl mit Einführnut -
Maße und Belastungen
Série aérospatiale - Rotule lisses en acier résistant à la corrosion avec encoches
d’assemblage - Dimensions et charges
Ta slovenski standard je istoveten z: EN 2588:2024
ICS:
49.035 Sestavni deli za letalsko in Components for aerospace
vesoljsko gradnjo construction
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 2588
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2024
EUROPÄISCHE NORM
ICS 49.035 Supersedes EN 2588:2006
English Version
Aerospace series - Bearing, spherical plain in corrosion
resisting steel with assembly slots - Dimensions and loads
Série aérospatiale - Rotule lisse en acier résistant à la Luft- und Raumfahrt - Gelenklager aus
corrosion avec encoches d'assemblage - Dimensions et korrosionsbeständigem Stahl mit Einführnut - Maße
charges und Belastungen
This European Standard was approved by CEN on 9 September 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 2588:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols and abbreviations . 4
5 Required characteristics . 5
5.1 Configuration, dimensions and masses . 5
5.2 Surface roughness . 5
5.3 Clearances and loads . 8
5.4 Materials . 9
5.5 Surface treatment . 9
6 Designation . 10
7 Marking . 10
8 Technical specification . 10
European foreword
This document (EN 2588:2024) has been prepared by the Aerospace and Defence Industries
Association of Europe — Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2025, and conflicting national standards shall be
withdrawn at the latest by April 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 2588:2006.
This document includes the following significant technical changes with respect to EN 2588:2006:
— normative references updated;
— subclause 5.4 “Materials”: hardness requirement for the outer ring corrected.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.