EN 2241:2010
(Main)Aerospace series - Lamp caps - Dimensions
Aerospace series - Lamp caps - Dimensions
This standard specifies the dimensions of caps for incandescent lamps used on board aircraft respectively the characteristics and tests of which are defined in EN 2240-001 and EN 2756.
Luft- und Raumfahrt - Lampensockel - Maße
Diese Norm legt die Maße für Sockel von Glühlampen zur Verwendung in Luftfahrzeugen, für die Eigenschaften
und Prüfungen in EN 2240-001 bzw. EN 2756 festgelegt sind, fest.
Série aérospatiale - Culots de lampes - Dimensions
Aeronavtika - Vznožki sijalk - Mere
Ta standard določa dimenzije vznožnih žarečih sijalk, uporabljenih na krovu zračnih plovil, oziroma lastnosti in preskuse, ki so določeni v EN 2240-001 in 2756.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Vznožki sijalk - MereLuft- und Raumfahrt - Lampensockel - MaßeSérie aérospatiale - Culots de lampes - DimensionsAerospace series - Lamp caps - Dimensions49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 2241:2010SIST EN 2241:2010en01-maj-2010SIST EN 2241:2010SLOVENSKI
STANDARD
SIST EN 2241:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2241
March 2010 ICS 49.060 English Version
Aerospace series - Lamp caps - Dimensions
Série aérospatiale - Culots de lampes - Dimensions
Luft- und Raumfahrt - Lampensockel - Maße This European Standard was approved by CEN on 27 February 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2241:2010: ESIST EN 2241:2010
EN 2241:2010 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Caps dimensions .44.1 General .44.2 Dimensions of bi-pin cap .54.3 Dimensions of SX4s/4 cap .64.4 Dimensions of SY4s/7 cap .74.5 Dimensions of SX6s cap .84.6 Dimensions of S5,7s/8 .94.7 Dimensions of BA7s/12 cap . 104.8 Dimensions of BA9s/13 cap . 114.9 Dimensions of BA15s/19 cap . 124.10 Dimensions of BA15s/19 cap . 134.11 Dimensions of BA15d/19 cap . 144.12 Dimensions of BAY15s/19 cap . 154.13 Dimensions of BA15s3/19 cap . 164.14 Dimensions of BA20d cap . 175 Quality assurance .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.