Footwear — Test methods for whole shoe — Flexing durability

This document specifies two test methods for the determination of the flexing durability of whole shoes. The two methods might not give comparable results. NOTE The selected test method depends on agreement between relative parties who use this test method or product standards which reference this test method. These methods are not applicable to the whole shoes with heel height more than 50 mm, or the thickness of flexing area of the soles more than 25 mm, or flexing angle less than 45° according to ISO 17707:2005, Clause 6.

Chaussures — Méthodes d'essai pour toute la chaussure — Durabilité vis-à-vis de la flexion

Le présent document spécifie deux méthodes d'essai pour la détermination de la durabilité vis-à-vis de la flexion de chaussures entières. Ces deux méthodes peuvent ne pas donner de résultats comparables. NOTE La méthode d'essai choisie dépend de l'accord passé entre les parties concernées qui utilisent cette méthode d'essai ou des normes de produits qui y font référence. Ces méthodes ne sont pas applicables aux chaussures entières dont la hauteur de talon est supérieure à 50 mm, dont l'épaisseur de la zone de flexion des semelles est supérieure à 25 mm ou dont l'angle de flexion est inférieur à 45° conformément à l'Article 6 de l'ISO 17707:2005.

General Information

Status
Published
Publication Date
05-Nov-2020
Current Stage
6060 - International Standard published
Start Date
06-Nov-2020
Due Date
08-Jul-2021
Completion Date
06-Nov-2020
Ref Project

Buy Standard

Standard
ISO 24266:2020 - Footwear -- Test methods for whole shoe -- Flexing durability
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 24266:2020 - Chaussures -- Méthodes d'essai pour toute la chaussure -- Durabilité vis-à-vis de la flexion
French language
11 pages
sale 15% off
Preview
sale 15% off
Preview
Draft
ISO/FDIS 24266:Version 25-apr-2020 - Footwear -- Test methods for whole shoe -- Flexing durability
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 24266
First edition
2020-11
Footwear — Test methods for whole
shoe — Flexing durability
Chaussures — Méthodes d'essai pour toute la chaussure — Durabilité
vis-à-vis de la flexion
Reference number
ISO 24266:2020(E)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 24266:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 24266:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus . 2
5.1 Method A . 2
5.2 Method B . 3
6 Sampling and conditioning . 5
7 Test method . 6
7.1 Method A . 6
7.2 Method B . 8
8 Test result . 9
9 Test report . 9
Bibliography .11
© ISO 2020 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 24266:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 216, Footwear, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 309, Footwear, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 24266:2020(E)
Footwear — Test methods for whole shoe — Flexing
durability
1 Scope
This document specifies two test methods for the determination of the flexing durability of whole
shoes. The two methods might not give comparable results.
NOTE The selected test method depends on agreement between relative parties who use this test method or
product standards which reference this test method.
These methods are not applicable to the whole shoes with heel height more than 50 mm, or the thickness
of flexing area of the soles more than 25 mm, or flexing angle less than 45° according to ISO 17707:2005,
Clause 6.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 18454, Footwear — Standard atmospheres for conditioning and testing of footwear and components
for footwear
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
4 Principle
The footwear specimen is repeatedly flexed through a specified angle about its normal flexing line by a
test machine. After a predetermined time or number of flexes the footwear is subjectively assessed for
signs of damage.
© ISO 2020 – All rights reserved 1

---------------------- Page: 5 ----------------------
ISO 24266:2020(E)

5 Apparatus
5.1 Method A
5.1.1 Flexing machine. See Figure 1.
5.1.1.1 A means of firmly clamping any type of footwear at the heel and toe. A number of toe clamps
will be necessary to ensure all sizes of footwear can be clamped securely.
Key
1 flexing angle indicator
2 front holding clamp
3 rear holding clamp
4 shoe platform
5 flexing axis
6 test piece (whole shoe)
Figure 1 — Flexing machine (method A)
5.1.1.2 A system of flexing the foot
...

NORME ISO
INTERNATIONALE 24266
Première édition
2020-11
Chaussures — Méthodes d'essai pour
toute la chaussure — Durabilité vis-à-
vis de la flexion
Footwear — Test methods for whole shoe — Flexing durability
Numéro de référence
ISO 24266:2020(F)
©
ISO 2020

---------------------- Page: 1 ----------------------
ISO 24266:2020(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2020
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2020 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 24266:2020(F)

Sommaire Page
Avant-propos .iv
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe . 1
5 Appareillage . 2
5.1 Méthode A . 2
5.2 Méthode B . 3
6 Échantillonnage et conditionnement . 5
7 Méthode d'essai . 6
7.1 Méthode A . 6
7.2 Méthode B . 8
8 Résultats de l'essai . 9
9 Rapport d’essai .10
Bibliographie .11
© ISO 2020 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 24266:2020(F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/ directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/ brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/ avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 216, Chaussure, en collaboration avec
le comité technique CEN/TC 309, Chaussure, du Comité européen de normalisation (CEN) conformément
à l’Accord de coopération technique entre l’ISO et le CEN (Accord de Vienne).
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes
se trouve à l’adresse www .iso .org/ fr/ members .html.
iv © ISO 2020 – Tous droits réservés

---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 24266:2020(F)
Chaussures — Méthodes d'essai pour toute la chaussure —
Durabilité vis-à-vis de la flexion
1 Domaine d'application
Le présent document spécifie deux méthodes d'essai pour la détermination de la durabilité vis-à-vis de
la flexion de chaussures entières. Ces deux méthodes peuvent ne pas donner de résultats comparables.
NOTE La méthode d'essai choisie dépend de l’accord passé entre les parties concernées qui utilisent cette
méthode d'essai ou des normes de produits qui y font référence.
Ces méthodes ne sont pas applicables aux chaussures entières dont la hauteur de talon est supérieure
à 50 mm, dont l'épaisseur de la zone de flexion des semelles est supérieure à 25 mm ou dont l'angle de
flexion est inférieur à 45° conformément à l'Article 6 de l'ISO 17707:2005.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique.
Pour les références non datées, la dernière édition du document de référence s'applique (y compris les
éventuels amendements).
ISO 18454, Chaussures — Atmosphères normales de conditionnement et d'essai des chaussures et de leurs
éléments constitutifs
3 Termes et définitions
Aucun terme n’est défini dans le présent document.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en
normalisation, consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse http:// www .electropedia .org/
4 Principe
L'échantillon de chaussure est plié à plusieurs reprises selon un angle spécifié, autour de sa ligne de
flexion naturelle, à l'aide d'une machine d’essai. Après un temps ou un nombre de flexions prédéterminé,
la chaussure est évaluée de façon subjective pour constater d’éventuels dommages.
© ISO 2020 – Tous droits réservés 1

---------------------- Page: 5 ----------------------
ISO 24266:2020(F)

5 Appareillage
5.1 Méthode A
5.1.1 Machine de flexion. Voir Figure 1.
5.1.1.1 Dispositif pour fixer fermement tout type de chaussure au niveau du talon et de la pointe.
Plusieurs pinces seront nécessaires au niveau de la pointe afin de garantir que toutes les chaussures
peuvent être fermement fixées, quelle que soit leur taille.
Légende
1 indicateur d'angle de flexion
2 pince de fixation à l'avant
3 pince de fixation à l'arrière
4 plateforme soutenant la chaussure
5 axe de flexion
6 éprouvette (chaussure entière)
Figure 1 — Machine de flexion (méthode A)
5.1.1.2 Système de flexion de la chaussure autour de sa ligne de flexion à une vitesse de (140 ± 10) cycles
par minute dans une gamme d'angles de flexion.
5.1.1.3 Dispositif pour enregistrer le nombre de flexions ou la durée de l'essai, à condition que la
vitesse de la machine soit constante et connue.
5.1.2 Pied à coulisse à vernier, avec une exactitude sup
...

DRAFT INTERNATIONAL STANDARD
ISO/DIS 24266
ISO/TC 216 Secretariat: UNE
Voting begins on: Voting terminates on:
2019-10-21 2020-01-13
Footwear — Test methods for whole shoe — Flexing
durability
ICS: 61.060
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24266:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 1 ----------------------
ISO/DIS 24266:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/DIS 24266:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
4.1 Method A . 1
4.1.1 Flexing machine . 1
4.1.2 Vernier caliper . 2
4.2 Method B . 2
4.2.1 Flexing machine . 2
4.2.2 Flexing last . 3
4.2.3 Vernier callipers . 4
4.2.4 Cutting tool . 4
5 Sampling and conditioning . 5
6 Test method . 5
6.1 Method A . 5
6.2 Method B . 6
7 Test result . 7
8 Test report . 7
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/DIS 24266:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 216, Footwear.
iv © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 24266:2019(E)
Footwear — Test methods for whole shoe — Flexing
durability
1 Scope
This International Standard specifies two test methods for the determination of the flexing durability
of whole shoes. The two methods may not give comparable results.
These methods are not applicable to the whole shoes with heel height more than 70 mm, or the thickness
of flexing area of the soles more than 25 mm, or flexing angle less than 45° according to ISO 17707:2005,
Clause 6 rigidity test.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.