EN 17150:2019

Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Test method for determination of short-term compression strength of boxes

This document specifies a method for determining short-term compression strength on boxes made of thermoplastics materials for non-pressure underground conveyance and storage of non-potable water.

Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung für Nicht-Trinkwasser - Prüfverfahren zur Bestimmung der Kurzzeitdruckfestigkeit von Versickerungsblöcken

Dieses Dokument legt ein Verfahren zur Bestimmung der Kurzzeitdruckfestigkeit an Versickerungsblöcken aus thermoplastischen Werkstoffen für die drucklose unterirdische Entwässerung und Speicherung von Nicht-Trinkwasser fest.

Systèmes de canalisations en plastique pour le transport et le stockage souterrains sans pression de l’eau non potable - Méthode d’essai pour la détermination de la résistance à la compression à court terme des structures alvéolaires ultra-légères

Le présent document spécifie une méthode pour déterminer la résistance à la compression à court terme des structures alvéolaires ultra-légères (SAUL) fabriquées à partir de matières thermoplastiques pour le transport et le stockage souterrains sans pression de l’eau non potable.

Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju - Preskusna metoda za ugotavljanje kratkotrajne tlačne odpornosti zabojev

Ta evropski standard določa metodo za ugotavljanje kratkotrajne tlačne odpornosti zabojev iz termoplastičnih materialov, ki delujejo po težnostnem principu in so položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju.

General Information

• Status: Published
• Publication Date: 20-Aug-2019
• Withdrawal Date: 27-Feb-2021
• ICS: 23.040.01 - Pipeline components and pipelines in general
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 26 - Storm Water Management
• Current Stage: 9020 - Submission to 2 Year Review Enquiry - Review Enquiry
• Start Date: 15-Oct-2024
• Completion Date: 15-Oct-2024
• Ref Project: SIST EN 17150:2019 - Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Test method for determination of short-term compression strength of boxes

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2019
Cevni sistemi iz polimernih materialov, ki delujejo po težnostnem principu in so
položeni v zemljo, za transport in shranjevanje vode, ki ni namenjena pitju -
Preskusna metoda za ugotavljanje kratkotrajne tlačne odpornosti zabojev
Plastics piping systems for non-pressure underground conveyance and storage of non-
potable water - Test method for determination of short-term compression strength of
boxes
Kunststoff-Rohrleitungssysteme für die drucklose unterirdische Entwässerung für Nicht-
Trinkwasser - Prüfverfahren zur Bestimmung der Kurzzeitdruckfestigkeit von
Versickerungsblöcken
Systèmes de canalisations en plastique pour le transport et le stockage souterrains sans
pression de l’eau non potable - Méthode d’essai pour la détermination de la résistance à
la compression à court terme des structures alvéolaires ultra-légères
Ta slovenski standard je istoveten z: EN 17150:2019
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 17150
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2019
EUROPÄISCHE NORM
ICS 23.040.01
English Version
Plastics piping systems for non-pressure underground
conveyance and storage of non-potable water - Test
method for determination of short-term compression
strength of boxes
Systèmes de canalisations en plastique pour le Kunststoff-Rohrleitungssysteme für die drucklose
transport et le stockage souterrains sans pression de unterirdische Entwässerung für Nicht-Trinkwasser -
l'eau non potable - Méthode d'essai pour la Prüfverfahren zur Bestimmung der
détermination de la résistance à la compression à court Kurzzeitdruckfestigkeit von Versickerungsblöcken
terme des structures alvéolaires ultra-légères
This European Standard was approved by CEN on 19 October 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17150:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Symbols and units . 5
5 Principle . 5
5.1 General . 5
5.2 Method A: Constant load rate . 5
5.3 Method B: Constant displacement rate . 6
6 Apparatus . 6
7 Test sample . 6
7.1 General . 6
7.2 Age . 7
7.3 Conditioning . 7
8 Procedure. 7
9 Expression of results . 9
10 Test report . 10

European foreword
This document (EN 17150:2019) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall be
withdrawn at the latest by February 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
Kingdom.
1 Scope
This document specifies a method for determining short-term compression strength on boxes made of
thermoplastics materials for non-pressure underground conveyance and storage of non-potable water.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 3126, Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126)
EN ISO 7500-1:2018, Metallic materials - Calibration and verification of static uniaxial testing machines -
Part 1: Tension/compression testing machines - Calibration and verification of the force-measuring system
(ISO 7500-1:2018)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
box
thermoplastic cuboid shaped element, with or without sidewalls, used to create a modular storage system
3.2
integral component
load bearing component contributing to the overall strength of the box
3.3
initial height, length, width
, l , b
hi i i
height (test direction), length and width of the sample before testing, respectively, in mm
3.4
initial height after pre-load
h
height of the sample after applying a pre-load, but before the load is further increased and recorded, in
mm
4 Symbols and units
For the purposes of this document, the following symbols and units apply.
Units
h initial height (test direction) mm
i
l initial length mm
i
b initial width mm
i
ε strain %
ε a predetermined maximum strain %
lim
h height of the test sample after pre-load mm
d displacement after correction of offset mm
c
F compression load kN
F maximum compression load kN
max
A initial (projected) surface area through which t
...