EN ISO 14852:2018
(Main)Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium - Method by analysis of evolved carbon dioxide (ISO 14852:2018)
Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous medium - Method by analysis of evolved carbon dioxide (ISO 14852:2018)
This document specifies a method, by measuring the amount of carbon dioxide evolved, for the determination of the degree of aerobic biodegradability of plastic materials, including those containing formulation additives. The test material is exposed in a synthetic medium under standardized laboratory conditions to an inoculum from activated sludge, mature compost or soil under aerobic, mesophilic conditions.
If an unadapted activated sludge is used as the inoculum, the test result can be used to assess the aerobic biodegradation processes which occur in a waste water treatment plant environment. If a mixed or pre-exposed inoculum is used, the method can be used to investigate the potential biodegradability of a test material.
The conditions used in this document do not necessarily correspond to the optimum conditions allowing maximum biodegradation to occur, but this test method is designed to measure the biodegradation of plastic materials and give an indication of their potential biodegradability.
The method enables the assessment of the biodegradation to be improved by calculating a carbon balance (optional, see Annex C).
The method applies to the following materials:
— natural and/or synthetic polymers, copolymers or mixtures thereof;
— plastic materials which contain additives such as plasticizers, colorants or other compounds;
— water-soluble polymers;
— materials which, under the test conditions, do not inhibit the microorganisms present in the inoculum. Inhibitory effects can be determined using an inhibition control or by another appropriate method (see, for example, ISO 8192[1]). If the test material is inhibitory to the inoculum, a lower test concentration, another inoculum or a pre-exposed inoculum can be used.
Bestimmung der vollständigen aeroben Bioabbaubarkeit von Kunststoff-Materialien in einem wässrigen Medium - Verfahren mittels Analyse des freigesetzten Kohlenstoffdioxides (ISO 14852:2018)
Évaluation de la biodégradabilité aérobie ultime des matériaux plastiques en milieu aqueux - Méthode par analyse du dioxyde de carbone libéré (ISO 14852:2018)
Le présent document spécifie une méthode d'évaluation du taux de biodégradabilité aérobie des matériaux plastiques, y compris ceux contenant des additifs, par la détermination de la quantité de dioxyde de carbone libéré. Le matériau d'essai en milieu synthétique est exposé dans des conditions de laboratoire normalisées à un inoculum provenant de boues activées, de compost mature ou de sol dans des conditions aérobies et mésophiles.
En cas d'utilisation comme inoculum de boues activées non adaptées, le résultat d'essai peut être utilisé pour évaluer les processus de biodégradation aérobie qui se produisent dans une installation de traitement des eaux résiduaires. Si on utilise un inoculum mélangé ou pré-exposé, la méthode permet d'étudier la biodégradabilité potentielle du matériau d'essai.
Les conditions utilisées dans le présent document ne correspondent pas nécessairement aux conditions optimales permettant d'obtenir le taux maximal de biodégradation; cependant, cette méthode d'essai est conçue pour mesurer la biodégradation des matériaux plastiques et pour donner une indication de leur biodégradabilité potentielle.
La méthode permet d'affiner l'évaluation de la biodégradation par le calcul d'un bilan carbone (facultatif, voir l'Annexe C).
La présente méthode s'applique aux matériaux suivants:
— polymères naturels et/ou synthétiques, copolymères ou mélanges de ceux-ci;
— matériaux plastiques contenant des additifs tels que plastifiants, colorants ou tout autre composé;
— polymères hydrosolubles;
— matériaux n'ayant pas d'effet inhibiteur dans les conditions d'essai sur les micro-organismes présents dans l'inoculum. Les effets inhibiteurs peuvent être déterminés en utilisant un dispositif de contrôle de l'inhibition ou par toute autre méthode appropriée (voir, par exemple, l'ISO 8192[1]). Si le matériau d'essai a un effet inhibiteur vis-à-vis de l'inoculum, il est possible d'utiliser une plus faible concentration, un autre inoculum ou un inoculum pré-exposé.
Določanje končne aerobne biorazgradljivosti polimernih materialov v vodnem mediju - Metoda z analizo sproščenega ogljikovega dioksida (ISO 14852:2018)
Ta dokument določa metodo za določanje stopnje aerobne biorazgradljivosti polimernih materialov, vključno s takšnimi, ki vsebujejo formulacijske dodatke, z merjenjem količine sproščenega ogljikovega dioksida. Preskusni material je izpostavljen inokulumu iz aktivnega blata, zrelega komposta ali zemljine pod aerobnimi mezofilnimi pogoji v sintetičnem mediju pod standardiziranimi laboratorijskimi pogoji.
Če je kot inokulum uporabljeno neprilagojeno aktivno blato, je mogoče rezultate preskusa uporabiti za dostop do procesov aerobne biorazgraditve, do katerih prihaja v okolju čistilne naprave za odpadno vodo. Če je uporabljen mešan ali znova izpostavljen inokulum, je mogoče metodo uporabiti za ugotavljanje potencialne biorazgradljivosti preskusnega
materiala.
Pogoji, ki so uporabljeni v tem dokumentu, niso nujno enaki idealnim pogojem, pri katerih pride do največje stopnje biorazgradljivosti, vendar je ta metoda zasnovana za merjenje biorazgraditve polimernih materialov in podaja oceno njihove potencialne biorazgradljivosti.
Metoda omogoča izboljšanje ocene biorazgradljivosti z izračunom ravnovesja
ogljika (izbirno, glej dodatek C).
Ta metoda se uporablja za naslednje materiale:
– naravne in/ali sintetične polimere, kopolimere ali njihove mešanice;
– polimerne materiale, ki vsebujejo dodatke, kot so mehčala, barvila ali druge spojine;
– polimere, topne v vodi;
– materiale, ki v preskusnih pogojih ne zavirajo delovanja mikroorganizmov, prisotnih v inokulumu. Zaviralne učinke je mogoče določiti na podlagi spremljanja zaviranja ali z drugo ustrezno metodo (glej npr. standard ISO 8192[1]). Če preskusni material zavira inokulum, se lahko uporabi manjša preskusna koncentracija, drug inokulum ali predhodno izpostavljeni inokulum.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 14852:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 14852:2004
'RORþDQMHNRQþQHDHUREQHELRUD]JUDGOMLYRVWLSROLPHUQLKPDWHULDORYYYRGQHP
PHGLMX0HWRGD]DQDOL]RVSURãþHQHJDRJOMLNRYHJDGLRNVLGD ,62
Determination of the ultimate aerobic biodegradability of plastic materials in an aqueous
medium - Method by analysis of evolved carbon dioxide (ISO 14852:2018)
Bestimmung der vollständigen aeroben Bioabbaubarkeit von Kunststoff-Materialien in
einem wässrigen Medium - Verfahren mittels Analyse des freigesetzten
Kohlenstoffdioxides (ISO 14852:2018)
Évaluation de la biodégradabilité aérobie ultime des matériaux plastiques en milieu
aqueux - Méthode par analyse du dioxyde de carbone libéré (ISO 14852:2018)
Ta slovenski standard je istoveten z: EN ISO 14852:2018
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 14852:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14852:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 14852:2018
EN ISO 14852
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 14852:2004
English Version
Determination of the ultimate aerobic biodegradability of
plastic materials in an aqueous medium - Method by
analysis of evolved carbon dioxide (ISO 14852:2018)
Évaluation de la biodégradabilité aérobie ultime des Bestimmung der vollständigen aeroben
matériaux plastiques en milieu aqueux - Méthode par Bioabbaubarkeit von Kunststoff-Materialien in einem
analyse du dioxyde de carbone libéré (ISO wässrigen Medium - Verfahren mittels Analyse des
14852:2018) freigesetzten Kohlenstoffdioxides (ISO 14852:2018)
This European Standard was approved by CEN on 26 August 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14852:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14852:2018
EN ISO 14852:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14852:2018
EN ISO 14852:2018 (E)
European foreword
This document (EN ISO 14852:2018) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14852:2004.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.