EN ISO 11833-1:2007

Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2007)

ISO 11833-1:2007 specifies the requirements for flat extruded sheets and pressed sheets of unplasticized poly(vinyl chloride) (PVC‑U) and the test methods to be used to measure the required values.
It applies only to sheets of thickness not less than 1,0 mm.
It does not cover biaxially stretched PVC‑U sheets.

Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften - Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2007)

Dieser Teil von ISO 11833 legt die Anforderungen an flache extrudierte Tafeln und gepresste Tafeln aus weichmacherfreiem Polyvinylchlorid (PVC U) und die zum Messen der geforderten Werte anzuwendenden Prüfverfahren fest.
Die Norm gilt nur für Tafeln mit einer Dicke von mindestens 1,0 mm.
Biaxial gereckte PVC U Tafeln werden nicht berücksichtigt.

Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Types, dimensions et caractéristiques - Partie 1: Plaques d'épaisseur non inférieure à 1 mm (ISO 11833-1:2007)

L'ISO 11833-1:2007 spécifie les exigences pour les plaques extrudées et les plaques pressées, planes, en poly(chlorure de vinyle) non plastifié (PVC‑U), ainsi que les méthodes d'essai à utiliser pour mesurer les valeurs requises.
Elle est applicable uniquement aux plaques d'épaisseur au moins égale à 1,0 mm.
Elle ne couvre pas les feuilles en PVC‑U biétirées.

Polimerni materiali - Nemehčane polivinilkloridne plošče - Vrste, mere in značilnosti - 1. del: Plošče z debelino več kot 1 mm (ISO 11833-1:2007)

General Information

• Status: Withdrawn
• Publication Date: 14-Oct-2007
• Withdrawal Date: 17-Jul-2012
• ICS: 83.140.10 - Films and sheets
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 18-Jul-2012
• Completion Date: 18-Jul-2012
• Ref Project: SIST EN ISO 11833-1:2009 - Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2007)

Relations

• Replaced By: EN ISO 11833-1:2012 - Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-februar-2009
3ROLPHUQLPDWHULDOL1HPHKþDQHSROLYLQLONORULGQHSORãþH9UVWHPHUHLQ
]QDþLOQRVWLGHO3ORãþH]GHEHOLQRYHþNRWPP,62
Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and
characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2007)
Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften
- Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2007)
Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Types, dimensions et
caractéristiques - Partie 1: Plaques d'épaisseur non inférieure a 1 mm (ISO 11833-
1:2007)
Ta slovenski standard je istoveten z: EN ISO 11833-1:2007
ICS:
83.140.10 Filmi in folije Films and sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 11833-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2007
ICS 83.140.10
English Version
Plastics - Unplasticized poly(vinyl chloride) sheets - Types,
dimensions and characteristics - Part 1: Sheets of thickness not
less than 1 mm (ISO 11833-1:2007)
Plastiques - Feuilles en poly(chlorure de vinyle) non Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln -
plastifié - Types, dimensions et caractéristiques - Partie 1: Typen, Maße und Eigenschaften - Teil 1: Tafeln mit einer
Plaques d'épaisseur non inférieure à 1 mm (ISO 11833- Dicke von mindestens 1 mm (ISO 11833-1:2007)
1:2007)
This European Standard was approved by CEN on 21 September 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11833-1:2007: E
worldwide for CEN national Members.

Contents Page
Foreword.3

Foreword
This document (EN ISO 11833-1:2007) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the
latest by April 2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 11833-1:2007 has been approved by CEN as a EN ISO 11833-1:2007 without any
modification.
INTERNATIONAL ISO
STANDARD 11833-1
Second edition
2007-10-15
Plastics — Unplasticized poly(vinyl
chloride) sheets — Types, dimensions
and characteristics —
Part 1:
Sheets of thickness not less than 1 mm
Plastiques — Feuilles en poly(chlorure de vinyle) non plastifié — Types,
dimensions et caractéristiques —
Partie 1: Plaques d'épaisseur non inférieure à 1 mm

Reference number
ISO 11833-1:2007(E)
©
ISO 2007
ISO 11833-1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

ISO 11833-1:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Material . 2
4 Classification. 2
5 Requirements . 2
5.1 Masking. 2
5.2 Appearance . 2
5.3 Colour . 2
5.4 Dimensions. 3
5.5 Basic properties. 4
5.6 Other mechanical and physical properties .6
5.7 Chemical and physiological properties. 6
6 Test methods. 6
6.1 General. 6
6.2 Appearance examination . 7
6.3 Dimensions. 7
6.4 Mechanical properties. 7
6.5 Thermal properties . 7
6.6 Total luminous transmittance. 9
6.7 Other mechanical and physical properties . 10
7 Marking . 10
Annex A (informative) Determination of resistance to delamination of thick pressed sheets using
a wedge. 11
Annex B (informative) Determination of resistance to delamination of thick pressed sheets
by thermal bending. 13

ISO 11833-1:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11833-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This second edition cancels and replaces the first edition (ISO 11833-1:1998), Table 5 of which has been
revised.
ISO 11833 consists of the following parts, under the general title Plastics — Unplasticized poly(vinyl chloride)
sheets — Types, dimensions and characteristics:
⎯ Part 1: Sheets of thickness not less than 1 mm
⎯ Part 2: Sheets of thickness less than 1 mm

iv © ISO 2007 – All rights reserved

INTERNATIONAL STANDARD ISO 11833-1:2007(E)

Plastics — Unplasticized poly(vinyl chloride) sheets — Types,
dimensions and characteristics —
Part 1:
Sheets of thickness not less than 1 mm
1 Scope
This part of ISO 11833 specifies the requirements for flat extruded sheets and pressed sheets of unplasticized
poly(vinyl chloride) (PVC-U) and the test methods to be used to measure the required values.
It applies only to sheets of thickness not less than 1,0 mm.
It does not cover biaxially stretched PVC-U sheets.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 75-2:2004, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and
ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 306:2004, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-2, Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
ISO 1163-1:1995, Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials —
Part 1: Designation system and basis for specifications
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient
column method
ISO 2039-1, Plastics — Determination of hardness — Part 1: Ball indentation method
ISO 11833-1:2007(E)
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 285
...