EN ISO 11833-1:2012

Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)

ISO 11833-1:2012 specifies the requirements for flat extruded sheets and pressed sheets of unplasticized poly(vinyl chloride) (PVC‑U) and the test methods to be used to measure the required values.
It applies only to sheets of thickness not less than 1,0 mm.
It does not cover biaxially stretched PVC‑U sheets.

Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften - Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2012)

Dieser Teil von ISO 11833 legt die Anforderungen an flache extrudierte Tafeln und gepresste Tafeln aus weichmacherfreiem Polyvinylchlorid (PVC U) und die zum Messen der geforderten Werte anzuwendenden Prüfverfahren fest.
Die Norm gilt nur für Tafeln mit einer Dicke von mindestens 1,0 mm.
Biaxial gereckte PVC U Tafeln werden nicht berücksichtigt.

Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Types, dimensions et caractéristiques - Partie 1: Plaques d'épaisseur non inférieure à 1 mm (ISO 11833-1:2012)

L'ISO 11833-1:2012 spécifie les exigences relatives aux plaques extrudées et aux plaques pressées, planes, en poly(chlorure de vinyle) non plastifié (PVC‑U), ainsi que les méthodes d'essai à utiliser pour mesurer les valeurs requises.
Elle est applicable uniquement aux plaques d'épaisseur au moins égale à 1,0 mm.
Elle ne s'applique pas aux feuilles en PVC‑U bi‑étirées.

Polimerni materiali - Nemehčane polivinilkloridne plošče - Vrste, mere in značilnosti - 1. del: Plošče z debelino več kot 1 mm (ISO 11833-1:2012)

Ta del standarda ISO 11833 določa zahteve za ploščate ekstrudirane plošče in stisnjene plošče iz nemehčanega polivinilklorida (PVC-U) ter preskusne metode, ki jih je treba uporabiti za merjenje zahtevanih vrednosti. Zadeva le plošče z debelino več kot 1 mm. Ne zajema dvoosno raztegnjenih polivinilkloridnih plošč.

General Information

• Status: Withdrawn
• Publication Date: 17-Jul-2012
• Withdrawal Date: 27-Aug-2019
• ICS: 83.140.10 - Films and sheets
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 28-Aug-2019
• Ref Project: SIST EN ISO 11833-1:2012 - Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)

Relations

• Replaces: EN ISO 11833-1:2007 - Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2007)
• Effective Date: 22-Dec-2008
• Replaced By: EN ISO 11833-1:2019 - Plastics - Unplasticized poly(vinyl chloride) sheets - Part 1: Types, dimensions and characteristics for sheets of thickness not less than 1 mm (ISO 11833-1:2019)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11833-1:2012
01-oktober-2012
1DGRPHãþD
SIST EN ISO 11833-1:2009
3ROLPHUQLPDWHULDOL1HPHKþDQHSROLYLQLONORULGQHSORãþH9UVWHPHUHLQ
]QDþLOQRVWLGHO3ORãþH]GHEHOLQRYHþNRWPP,62
Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and
characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012)
Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln - Typen, Maße und Eigenschaften
- Teil 1: Tafeln mit einer Dicke von mindestens 1 mm (ISO 11833-1:2012)
Plastiques - Feuilles en poly(chlorure de vinyle) non plastifié - Types, dimensions et
caractéristiques - Partie 1: Plaques d'épaisseur non inférieure à 1 mm (ISO 11833-
1:2012)
Ta slovenski standard je istoveten z: EN ISO 11833-1:2012
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 11833-1:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11833-1:2012

---------------------- Page: 2 ----------------------

SIST EN ISO 11833-1:2012


EUROPEAN STANDARD
EN ISO 11833-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2012
ICS 83.140.10 Supersedes EN ISO 11833-1:2007
English Version
Plastics - Unplasticized poly(vinyl chloride) sheets - Types,
dimensions and characteristics - Part 1: Sheets of thickness not
less than 1 mm (ISO 11833-1:2012)
Plastiques - Feuilles en poly(chlorure de vinyle) non Kunststoffe - Weichmacherfreie Polyvinylchloridtafeln -
plastifié - Types, dimensions et caractéristiques - Partie 1: Typen, Maße und Eigenschaften - Teil 1: Tafeln mit einer
Plaques d'épaisseur non inférieure à 1 mm (ISO 11833- Dicke von mindestens 1 mm (ISO 11833-1:2012)
1:2012)
This European Standard was approved by CEN on 23 June 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11833-1:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11833-1:2012
EN ISO 11833-1:2012 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11833-1:2012
EN ISO 11833-1:2012 (E)
Foreword
This document (EN ISO 11833-1:2012) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2013, and conflicting national standards shall be withdrawn at
the latest by January 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11833-1:2007.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, the United Kingdom and Turkey.
Endorsement notice
The text of ISO 11833-1:2012 has bee
...