EN 3368:2008

Aerospace series - Aerospace design standard - Holes for locating pins

This standard provides particulars of hole sizes and associated fitting conditions to suit locating pins EN 3150 and EN 3151 series.

Luft- und Raumfahrt - Löcher für Zylinderstifte - Konstruktionsnorm

Diese Norm enthält Angaben zu den Lochmaßen und jeweiligen Passungsbedingungen für Zylinderstifte nach EN 3150 und EN 3151.

Série aérospatiale - Trous pour pieds de centrage - Normes de conception

Aeronavtika - Standard za projektiranje - Luknje za valjaste zatiče

General Information

• Status: Published
• Publication Date: 01-Apr-2008
• Withdrawal Date: 30-Oct-2008
• ICS: 49.030.01 - Fasteners in general
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 02-Apr-2008
• Completion Date: 02-Apr-2008
• Ref Project: SIST EN 3368:2008 - Aerospace series - Aerospace design standard - Holes for locating pins

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.þHLuft- und Raumfahrt - Löcher für Zylinderstifte - KonstruktionsnormSérie aérospatiale - Trous pour pieds de centrage - Normes de conceptionAerospace series - Aerospace design standard - Holes for locating pins49.030.40Pins, nailsICS:Ta slovenski standard je istoveten z:EN 3368:2008SIST EN 3368:2008en,de01-julij-2008SIST EN 3368:2008SLOVENSKI
STANDARD



SIST EN 3368:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3368April 2008ICS 49.030.01 English VersionAerospace series - Aerospace design standard - Holes forlocating pinsSérie aérospatiale - Trous pour pieds de centrage - Normesde conceptionLuft- und Raumfahrt - Löcher für Zylinderstifte -KonstruktionsnormThis European Standard was approved by CEN on 3 November 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3368:2008: ESIST EN 3368:2008



EN 3368:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Locating pins.4 4 Hole sizes, positional tolerances and chamfer sizes.4 5 Counterbore sizes.5 6 Air release holes.5 7 Hole tolerance grade designations.7 8 Dimensional particulars for holes.7 9 Fitting conditions in steel, nimonic, titanium and similar alloys.8 10 Fitting conditions in light alloy materials.8
Figures Figure 1.5 Figure 2.5 Figure 3.6 Figure 4.6
Tables Table 1.4 Table 2.7 Table 3.7 Table 4.
...