EN ISO 25197:2020
(Main)Small craft - Electrical/electronic control systems for steering, shift and throttle (ISO 25197:2020)
Small craft - Electrical/electronic control systems for steering, shift and throttle (ISO 25197:2020)
This document establishes the requirements for the design, construction and testing of electrical/electronic steering, shift and throttle systems and dynamic positioning control systems, or combinations thereof, on small craft of up to 24 m length of hull.
This document does not apply to electric trolling motors and autopilot systems on sailing craft.
Kleine Wasserfahrzeuge - Elektrische/elektronische Regelungssysteme für Steuerung, Schaltung und Antrieb (ISO 25197:2020)
Dieses Dokument legt die Anforderungen für den Entwurf, die Ausführung und die Prüfung von elektrischen/elektronischen Systemen für die Steuerung, Getriebeschaltung und die Drehzahlregelung, sowie von dynamischen Positionskontrollsystemen oder Kombinationen davon auf kleinen Wasserfahrzeugen mit einer Rumpflänge bis 24 m fest.
Dieses Dokument gilt nicht für elektrische Außenbordmotoren und Schiffs-Voraus-Steuerungssysteme auf Segelfahrzeugen.
Petits navires - Systèmes électriques/électroniques pour le contrôle de la direction, de l'inverseur et des gaz (ISO 25197:2020)
Le présent document établit les exigences relatives à la conception, la construction et les essais des systèmes électriques/électroniques de contrôle de la direction, de commandes d'inverseur, des gaz et de positionnement dynamique, ou de leur combinaison, sur les petits navires d'une longueur de coque inférieure ou égale à 24 m.
Le présent document ne s'applique pas aux moteurs électriques de pêche à la traîne et aux pilotes automatiques installés sur les voiliers.
Mala plovila - Električni/elektronski regulacijski sistem za krmarjenje, prestavljanje in pogon (ISO 25197:2020)
Standard EN ISO 25197 določa zahteve za načrtovanje, konstrukcijo in preskušanje električnih/elektronskih regulacijskih sistemov za krmarjenje, prestavljanje in pogon ter dinamično določanje položaja ali njihovo kombinacijo pri malih plovilih z dolžino trupa do 24 m. Ta dokument se ne uporablja za električne motorje za vleko in avtopilotne sisteme plovil.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2020
Nadomešča:
SIST EN ISO 25197:2018
Mala plovila - Električni/elektronski regulacijski sistem za krmarjenje, prestavljanje
in pogon (ISO 25197:2020)
Small Craft - Electrical/electronic control system for steering, shift and throttle (ISO
25197:2020)
Kleine Wasserfahrzeuge - Elektrische/elektronische Regelungssysteme für Steuerung,
Schaltung und Antrieb (ISO 25197:2020)
Petits navires - Système électrique/électronique pour le contrôle de la direction, de
l'inverseur et des gaz (ISO 25197:2020)
Ta slovenski standard je istoveten z: EN ISO 25197:2020
ICS:
47.020.60 Električna oprema ladij in Electrical equipment of ships
konstrukcij na morju and of marine structures
47.080 Čolni Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 25197
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2020
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 25197:2018
English Version
Small craft - Electrical/electronic control systems for
steering, shift and throttle (ISO 25197:2020)
Petits navires - Systèmes électriques/électroniques Kleine Wasserfahrzeuge - Elektrische/elektronische
pour le contrôle de la direction, de l'inverseur et des Regelungssysteme für Steuerung, Schaltung und
gaz (ISO 25197:2020) Antrieb (ISO 25197:2020)
This European Standard was approved by CEN on 7 March 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25197:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
European foreword
This document (EN ISO 25197:2020) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 25197:2018.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 25197:2020 has been approved by CEN as EN ISO 25197:2020 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
M/542/C(2015) 8736 final to provide one voluntary means of conforming to essential requirements of
Directive 2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of
Directive 2013/53/EU
Essential Requirements of Clause(s)/sub- Remarks/Notes
Directive 2013/53/EU clause(s)of this EN
Annex I, sub clause 2.5 4.7, 4.11, 12 These clauses specify the information to be
included in the owner’s manual.
Owner’s manual
Annex I, 5.4 Steering system 10.2 In respect of transmission of steering loads in
all foreseeable conditions.
5.4.1 General
Annex I, 5.4 Steering system 9.1.4 In respect of single engine non-sailing craft
with remote rudder steering only.
5.4.2 Emergency
arrangements
Annex II (3) - Steering wheels, 10.2 In respect of the transmission of steering loads
steering mechanisms and in for electric/electronic steering systems
cable assemblies supplied as components only.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 25197
Second edition
2020-04
Small craft — Electrical/electronic
control systems for steering, shift and
throttle
Petits navires — Systèmes électriques/électroniques pour le contrôle
de la direction, de l'inverseur et des gaz
Reference number
ISO 25197:2020(E)
©
ISO 2020
ISO 25197:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 25197:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General requirements . 5
5 Control head . 6
6 Command station transfer . 8
7 Portable helm station controls . 8
8 Dynamic-positioning system (DPS) . 8
9 Failure modes and responses . 9
9.1 Loss of operation . 9
9.2 Loss of computer command logic . 9
10 Test requirements .10
10.1 General test requirements .10
10.2 Steering .10
10.3 Control lever(s) for separate or combined shift and throttle functions .10
10.4 Joystick .11
10.5 Environmental-test requirements.12
10.5.1 General.12
10.5.2 Salt mist tests .13
10.5.3 Damp heat — Cyclic .14
10.5.4 Damp heat — Steady state .14
10.5.5 High-temperature test — Operation .14
10.5.6 High-temperature test — Storage .14
10.5.7 Low-temperature test — Operation.15
10.5.8 Low-temperature test — Storage .15
10.6 Vibration tests and requirements .15
10.7 Shock testing .16
10.8 Drop test .16
10.9 Resistance to UV .16
10.10 Electromagnetic compatibility (EMC).17
10.10.1 Electromagnetic interference tests .17
10.10.2 EMC performance criteria . .17
10.10.3 Immunity to conducted low-frequency interference .17
10.10.4
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.