EN 14565:2004
(Main)Resilient floor coverings - Floor coverings based upon synthetic thermoplastic polymers - Specification
Resilient floor coverings - Floor coverings based upon synthetic thermoplastic polymers - Specification
This European Standard specifies the characteristics for resilient floor coverings based upon synthetic thermoplastic polymers, supplied either in roll or tile form.
This specification does not apply to floor coverings specified in the series EN 649 to EN 654.
Elastische Bodenbeläge - Bodenbeläge auf Basis synthetischer Thermoplaste - Spezifikation
Diese Europäische Norm legt die Eigenschaften für elastische Bodenbeläge auf Basis synthetischer thermoplastischer Polymere auf Rolle oder in Plattenform fest.
Diese Spezifikation gilt nicht für Bodenbeläge, die in den Reihen EN 649 bis EN 654 festgelegt sind.
Revêtements de sol résilients - Revêtements de sol à base de polymères thermoplastiques synthétiques - Spécification
La présente Norme européenne spécifie les caractéristiques relatives aux revêtements de sol résilients à base de polymères thermoplastiques synthétiques, fournis en rouleaux ou en dalles.
Cette spécification ne s'applique pas aux revêtements de sol de la série EN 649 à EN 654.
Elastične talne obloge – Talne obloge na osnovi sintetičnih termoplastičnih polimerov - Specifikacija
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SODVWLþQLKElastische Bodenbeläge - Bodenbeläge auf Basis synthetischer Thermoplaste - SpezifikationRevetements de sol résilients - Revetements de sol a base de polymeres thermoplastiques synthétiques - SpécificationResilient floor coverings - Floor coverings based upon synthetic thermoplastic polymers - Specification97.150Netekstilne talne oblogeNon-textile floor coveringsICS:Ta slovenski standard je istoveten z:EN 14565:2004SIST EN 14565:2004en01-november-2004SIST EN 14565:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14565June 2004ICS 97.150English versionResilient floor coverings - Floor coverings based upon syntheticthermoplastic polymers - SpecificationRevêtements de sol résilients - Revêtements de sol à basede polymères thermoplastiques synthétiques - SpécificationElastische Bodenbeläge - Bodenbeläge auf Basissynthetischer Thermoplaste - SpezifikationThis European Standard was approved by CEN on 1 April 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14565:2004: ESIST EN 14565:2004
Method of test for resistance to scratching.9 A.1 Introduction.9 A.2 Principle.9 A.3 Apparatus and materials.9 A.4 Sampling and conditioning.11 A.5 Procedure.12 A.6 Evaluation.12 A.7 Report.12 A.8 Calibration of steel pins.12 Annex B (normative)
Method of test for resistance to soiling and ease of cleaning.14 B.1 Introduction.14 B.2 Principle.14 B.3 Apparatus and materials.14 B.4 Preparation and conditioning of test pieces.15 B.5 Procedure.15 B.6 Evaluation.16 B.7 Test report.16 Annex C (normative)
Method of test for dimensional stability.17 C.1 Introduction.17 C.2 Principle.17 C.3 Apparatus and material.17 C.4 Sampling and conditioning.17 C.5 Procedure.18 C.6 Evaluation and statements of the results.18 C.7 Test report.18 Annex D (informative)
Optional properties.19 Annex E (informative)
Additional test methods.20 Bibliography.21
1 Scope This European Standard specifies the characteristics for resilient floor coverings based upon synthetic thermoplastic polymers, supplied either in roll or tile form. This specification does not apply to floor coverings specified in the series EN 649 to EN 654. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 425, Resilient and laminate floor coverings – Castor chair test. EN 426, Resilient floor coverings – Determination of width, length, straightness and flatness of sheet material. EN 427, Resilient floor coverings – Determination of the side length, squareness and straightness of tiles. EN 428, Resilient floor coverings – Determination of overall thickness. EN 429, Resilient floor coverings - Determination of the thickness of layers. EN 430, Resilient floor coverings – Determination of mass per unit area. EN 431, Resilient floor coverings – Determination of peel resistance. EN 433, Resilient floor coverings – Determination of residual indentation after static loading. EN 434, Resilient floor coverings – Determination of dimensional stability and curling after exposure to heat. EN 435, Resilient floor coverings – Determination of flexibility. EN 684, Resilient floor coverings – Determination of seam strength. EN 685, Resilient, textile and laminate floor coverings – Classification. EN 1269, Textile floor coverings – Assessment of impregnations in needled floor coverings by means of a soiling test. EN 1372, Adhesives – Test method for adhesives for floor and wall coverings – Peel test. EN 1373, Adhesives – Test method for adhesives for floor and wall coverings – Shear test. EN 1471, Textile floor coverings – Assessment of changes in appearance. EN 1903, Adhesives – Test method for adhesives for plastic or rubber floor coverings or wall coverings – Determination of dimensional changes after accelerated ageing. EN 12466:1998, Resilient floor coverings – Vocabulary. SIST EN 14565:2004
3 Terms and definitions For the purposes of this European Standard, the terms and definitions in EN 12466:1998 and the following apply. 3.1 product with backing floor covering consisting of a homogeneous or heterogeneous surface layer and a backing of any material different from the surface layer NOTE Typical backing materials are cork, foams and jute. 3.2 scratch permanent surface damage of visible physical nature 4 Requirements 4.1 General requirements Floor coverings described in this standard shall comply with the appropriate general requirements specified in Table 1, when tested in accordance with the methods given therein. Table 1 Requirements Characteristic
Requirement Test method For product without backing For product with backing
Roll form - Length m - Width mm
not less than the nominal value
EN 426 Tiles Side length mm Squareness and straightness
deviation ± 0,13 % of nominal length up to 0,5 mm maximum
EN 427 SIST EN 14565:2004
Requirement Test method For product without backing For product with backing
for side length mm - ≤ 400 mm - > 400 mm - > 400 mm (intended for welding) deviation at any point ≤ 0,25 ≤ 0,35 ≤ 0,50 Overall thickness mm - averagea
- individual results nominal value + 0,13 -0,10 average valueb ± 0,15 nominal value + 0,18 - 0,15 average valueb ± 0,20 EN 428 Thickness of wear layer mm - averagea
- individual results
nominal value
+ 13 % − 10 % average valueb ± 0,15
nominal value + 18 % − 15 % average valueb ± 0,20
EN 429 Total mass per unit area g/m2 (average) nominal value + 13 % − 10 % EN 430 Residual indentation mm Recovery after indentation %
≤ 0,10
≥ 80 EN 433 EN 433c Dimensional stability after exposure to heat Expansion/Shrinkage %
≤ 0,20 Annex C Curling under exposure to heat Rolls and tiles (intended for welding) mm Tiles (intended for dry joint laying) mm
≤ 8
≤ 2 EN 434(6 h, 50 °C) SIST EN 14565:2004
Requirement Test method For product without backing For product with backing
Flexibility Test using a 20 mm mandrel. For products which show signs of cracking, perform a further test using a 40 mm mandrel. If results show no further cracking, record the use of a 40 mm diameter mandrel. Cracking when using a 40 mm mandrel is to be recorded. The test shall be repeated with method B. If no cracking occurs the material is semi flexible. EN 435 Method A Method B Colour fastness to artificial light 6 minimum EN ISO 105 B02 Method 3d Peel resistance N/50 mm Average Individual results
≥ 50 ≥ 40 EN 431 Soiling Ease of cleaning > 2 big grey scale ≥ 4 big grey scale Annex B Scratch Appearance Assessment Record the load which causes the first uninterrupted scratch on the surface (visible with the naked eye) Annex A Adhesion and gluing e: Peel strength N/mm Shear strength N/mm²
> 1,0 > 0,30
EN 1372 EN 1373 Castor chair suitability For classes 32 and higher – no delamination EN 425 Seam strength N/50 mm For classes 31 and higher, if welding is required:
average ≥ 240 i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.