EN ISO 19115-2:2019
(Main)Geographic information - Metadata - Part 2: Extensions for acquisition and processing (ISO 19115-2:2019)
Geographic information - Metadata - Part 2: Extensions for acquisition and processing (ISO 19115-2:2019)
This document extends ISO 19115-1:2014 by defining the schema required for an enhanced description
of the acquisition and processing of geographic information, including imagery. Included are the
properties of measuring systems and the numerical methods and computational procedures used to
derive geographic information from the data acquired by them. This document also provides the XML
encoding for acquisition and processing metadata thereby extending the XML schemas defined in ISO/
TS 19115-3.
Geoinformation - Metadaten - Teil 2: Erweiterungen für Erhebung und Verarbeitung (ISO 19115-2:2019)
Information géographique - Métadonnées - Partie 2: Extensions pour l'acquisition et le traitement (ISO 19115-2:2019)
Geografske informacije - Metapodatki - 2. del: Razširitev za zajemanje in obdelavo geografskih informacij (ISO 19115-2:2019)
Ta dokument razširja področje uporabe standarda ISO 19115-1:2014 z opredelitvijo sheme, ki je potrebna za izboljšan opis zajemanja in obdelave geografskih informacij, vključno s posnetki. Vključene so lastnosti merilnih sistemov ter računske metode in postopki, ki se uporabljajo za pridobivanje geografskih informacij iz podatkov, zajetih z merilnimi sistemi. Ta dokument vključuje tudi kodiranje XML za zajemanje in obdelavo metapodatkov, s čimer razširja sheme XML, opredeljene v standardu ISO/TS 19115-3.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2019
Nadomešča:
SIST EN ISO 19115-2:2010
Geografske informacije - Metapodatki - 2. del: Razširitev za zajemanje in obdelavo
geografskih informacij (ISO 19115-2:2019)
Geographic information - Metadata - Part 2: Extensions for acquisition and processing
(ISO 19115-2:2019)
Geoinformation - Metadaten - Teil 2: Erweiterungen für Bild- und Rasterdaten (ISO
19115-2:2019)
Information géographique - Métadonnées - Partie 2: Extensions pour l'acquisition et le
traitement (ISO 19115-2:2019)
Ta slovenski standard je istoveten z: EN ISO 19115-2:2019
ICS:
07.040 Astronomija. Geodezija. Astronomy. Geodesy.
Geografija Geography
35.240.70 Uporabniške rešitve IT v IT applications in science
znanosti
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 19115-2
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2019
EUROPÄISCHE NORM
ICS 35.240.70 Supersedes EN ISO 19115-2:2010
English Version
Geographic information - Metadata - Part 2: Extensions for
acquisition and processing (ISO 19115-2:2019)
Information géographique - Métadonnées - Partie 2: Geoinformation - Metadaten - Teil 2: Erweiterungen
Extensions pour l'acquisition et le traitement (ISO für Erhebung und Verarbeitung (ISO 19115-2:2019)
19115-2:2019)
This European Standard was approved by CEN on 24 February 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19115-2:2019 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 19115-2:2019) has been prepared by Technical Committee ISO/TC 211
"Geographic information/Geomatics" in collaboration with Technical Committee CEN/TC 287
“Geographic Information” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2019, and conflicting national standards shall
be withdrawn at the latest by August 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19115-2:2010.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19115-2:2019 has been approved by CEN as EN ISO 19115-2:2019 without any
modification.
INTERNATIONAL ISO
STANDARD 19115-2
Second edition
2019-01
Geographic information —
Metadata —
Part 2:
Extensions for acquisition and
processing
Information géographique — Métadonnées —
Partie 2: Extensions pour l'acquisition et le traitement
Reference number
ISO 19115-2:2019(E)
©
ISO 2019
ISO 19115-2:2019(E)
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
ISO 19115-2:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms . 4
4.1 Abbreviated terms . 4
5 Conformance . 5
5.1 Conformance requirements . 5
5.2 Metadata profiles . 5
6 Acquisition and processing metadata . 5
6.1 Metadata for acquisition and processing requirements . 5
6.2 Acquisition and processing metadata packages and dependencies . 5
6.3 Acquisition and processing metadata class diagrams by package . 6
6.3.1 Introduction . 6
6.3.2 Acquisition Information . 7
6.3.3 Extended Lineage information .10
6.3.4 Extended spatial representation information — Geolocation information .11
6.3.5 Extended Content information — Imagery .13
Annex A (normative) Conformance .15
Annex B (normative) Acquisition and processing metadata data dictionary .18
Annex C (informative) XML schema implementation .56
Bibliography .57
ISO 19115-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by ISO/TC 211, Geographic information/Geomatics.
This second edition cancels and replaces the first edition (ISO 19115-2:2009), which has been technically
revised.
The following is a summary of major changes to this document during the revision process:
— The name and scope were changed to better describe the purpose of the document;
— QE_CoverageResult and QE_Useability were moved to ISO 19157;
— All extended classes now extend ISO 19115-1:2014;
— Whereas the XML Schema encoding for ISO 19115-2:2009 was provided in ISO/TS 19139-2; the link
and information about the XML schema for this revision is provided in Annex C of this document;
— A specified class of MI_Instrument – MI_Sensor was defined. A list of all the parts in the ISO 19115
series, can be found on the ISO website.
iv © ISO 2019 – All rights reserved
ISO 19115-2:2019(E)
Introduction
This document replaces the previous edition (ISO 19115-2:2009) Geographic information — Metadata
— Extension for imagery and gridded data, which focused on metadata for imagery and gridded data
as they are important information sources and products used within a geospatial environment by
geographic information systems. During the revision process it was noted that this metadata applied
to the acquisition and processing of geographic information from all sources not just imagery and
gridded data. Hence, the new title Geographic information — Metadata — Extensions for acquisition and
processing. The production of all geographic information, including imagery and gridded data, follows
one or more process chains that begins with remote sensing data, scanned maps, field data collection
or other sensing methods and ends with the creation of the end data products. The production process
needs to be documented to maintain quality control over the end products. In addition, metadata about
the geometry of the measuring process and the properties of the measuring equipment need to be
retained with the raw data to support the production process.
The object of this document is to provide the additional structure needed to more extensively describe
the acquisition and processing of geographic information from all sources. This structure is intended
to augment ISO 19115-1. This document also provides an XML schema for implementing this document
using ISO/TS 19115-3.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.